Welding Parameters
Mostrando 25-36 de 119 artigos, teses e dissertações.
-
25. A Comparative Study of the Heat Input During Laser Welding of Aeronautical Aluminum Alloy AA6013-T4
ABSTRACT The heat input is the amount of energy supplied per unit length of the welded workpiece. In this study, the effect of two different heat inputs in laser beam welding of a high strength aluminum alloy AA6013-T4 was evaluated from macrostructural and microstructural points of view. The experiments were performed using a continuous wave 2 kW Yb-fiber l
J. Aerosp. Technol. Manag.. Publicado em: 14/06/2018
-
26. Investigation of Mechanical and Metallurgical Properties of Friction Stir Corner Welded Dissimilar Thickness AA5086-AA6061 Aluminium Alloys
In this investigation, an attempt has been made to fabricate dissimilar thickness corner joint using non-heat treatable (AA5086) and heat treatable (AA6061) dissimilar aluminium alloys by friction stir welding process with plate thicknesses of 6mm and 4mm. Three parameters and three levels were considered to conduct the experiments such as welding and rotati
Mat. Res.. Publicado em: 11/06/2018
-
27. Effect of Process Parameters on Microstructure and Mechanical Properties of Friction Stir Welded Cast Nickel Aluminum Bronze Alloy (C95800)
In the present study, Friction Stir Welding (FSW) of Nickel Aluminum Bronze (NAB) alloy was carried out by varying the axial load, rotation speed and welding speed rate. Micro-structural analyses of these samples revealed the different grain sizes and shapes of the various zones. Hardness and tensile strength tests were carried out for the samples welded at
Mat. Res.. Publicado em: 24/05/2018
-
28. Effects of Local Heat Input Conditions on the Thermophysical Properties of Super Duplex Stainless Steels (SDSS)
The properties of the super duplex stainless steels (SDSS) are strongly affected by the thermal history imposed by welding procedures. The controlled dual phase microstructure (ferrite and austenite) guarantee excellent mechanical properties such as mechanical strength and corrosion resistance, in addition to small thermal expansion coefficient and high ther
Mat. Res.. Publicado em: 11/01/2018
-
29. Welded Joints' Heat Affected Zone's Extension Prediction by Switching Welding Parameters
Choosing welding parameters is an important step in welding process, directly influencing in the heat input provided to welded joints. This heat input value, along with temperature distribution in welded joints, provides, to the drafter, conditions of predicting the Heat Affected Zone (HAZ) extension, the kind of microstructure to be formed, and therefore, t
Mat. Res.. Publicado em: 30/11/2017
-
30. Effect of Preheating on Microstructure and Tensile Properties of Friction Stir Welded AA7075 Aluminium Alloy Joints
ABSTRACT The high strength AA7075 aluminum alloy is commonly used in the aerospace components due to its exclusive mechanical properties like lightweight and high strength. This alloy cannot be welded by fusion welding techniques due to solidification cracking which severely degrade the mechanical properties of the joint. In contrast, through friction stir w
Braz. arch. biol. technol.. Publicado em: 23/01/2017
-
31. Friction Stir Welding of AZ31 Magnesium Alloys - A Numerical and Experimental Study
Abstract In this paper, weldability of magnesium alloys by friction stir welding (FSW) method which is difficult to join by the fusion welding have been investigated experimentally and numerically. To this end, the connection of magnesium alloys was performed using different welding parameters. AZ31 Mg-alloy plates were friction stir welded at rotation speed
Lat. Am. j. solids struct.. Publicado em: 2017-01
-
32. Soldabilidad de Polietileno de Alta Densidad Usando Soldadura por Fricción-agitación con una Herramienta de Hombro no Rotacional
Abstract: In this work was studied the weldability of high density polyethylene (HDPE) using friction stir welding (FSW) process, and two kind of tools, denominated conventional, and non-conventional tool, which has a non-rotating shoulder. Evaluation was performed using combination of parameters of rotation speed (vW) and welding speed (vA), which were adju
Soldag. insp.. Publicado em: 2016-12
-
33. A Study on Process Characteristics and Performance of Hot Wire Gas Tungsten Arc Welding Process for High Temperature Materials
Hot wire gas tungsten arc welding (HW-GTAW) process is the one where the filler wire is pre-heated close to its melting point before it is fed in to the arc. The effect of HW-GTAW parameters such as welding current, hot wire current and the wire feed rate during welding of super ASS 304H stainless steel tubes were evaluated in terms of heat input, voltage-cu
Mat. Res.. Publicado em: 28/11/2016
-
34. Residual Stress, Microstructure and Hardness of Thin-Walled Low-Carbon Steel Pipes Welded Manually
The aim of this work is to evaluate the welding residual stress profile in ASTM A106 Gr. B steel pipes with 4" diameter and to correlate this profile with the microstructure and hardness of the joint. The results showed that the residual stresses are more uniform for a lower welding heat input. Higher welding heat input causes not only a non-uniformity of th
Mat. Res.. Publicado em: 29/09/2016
-
35. Efecto del Gas de Protección, Ángulos de Trabajo y Desplazamiento sobre las Características de Juntas de Filete Obtenidas por GMAW en un Acero Microaleado de Alta Resistencia
Abstract: The fillet joint is one of the most used in several industries, particularly in the agricultural machinery. However, many times, the complexity of the parts to be joined difficult welder accessibility, therefore working and travel angles are important variables to analyze. Furthermore, in GMAW process, employing shielding gas mixture Ar-20%CO2 has
Soldag. insp.. Publicado em: 2016-09
-
36. Cold metal transfer welding of AA1050 aluminum thin sheets
ABSTRACT This study was aimed to investigate the welding parameters on mechanical behavior of 2 mm thick AA1050 sheet materials joined by cold metal transfer (CMT) method. Macro structural examination showed that decreasing heat input decreased the pore size in the weld metal. Tensile test was applied and failure occurred in heat affected zone of aluminum sh
Matéria (Rio J.). Publicado em: 2016-09