Steel Fracture
Mostrando 1-12 de 133 artigos, teses e dissertações.
-
1. Post-elastic Deformation Characteristics of Hybrid Fibre Reinforced Concrete Composites
Abstract The present study was focused on evaluating the strength and failure properties of hybrid micro-fibre concretes containing micro brass and steel fibre additions. Experimental tests were conducted on different hybrid fibre concretes containing aligned fibres in the direction of beam axis and the relative mechanical performance was compared to randoml
Lat. Am. j. solids struct.. Publicado em: 10/01/2020
-
2. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
3. Fracture strength of monocrystalline and polycrystalline ceramic brackets during archwire torque
Resumo Introdução A demanda por tratamentos estéticos tem crescido nos últimos anos, sendo cada vez mais forte a preocupação com a estética por parte dos pacientes que buscam o tratamento ortodôntico. Objetivo Este estudo avaliou a resistência à fratura de bráquetes cerâmicos monocristalinos e policristalinos de diferentes fabricantes quando su
Rev. odontol. UNESP. Publicado em: 03/10/2019
-
4. Aço de alta dureza para aplicação balística: propriedades mecânicas
RESUMO Blindagens balísticas são projetadas a resistir determinadas ameaças, que dependem da aplicação. Estas ameaças podem ser geradas por projéteis de armas de fogo ou estilhaços provenientes de explosões com diferentes energias cinéticas. Os materiais normalmente utilizados para este propósito são metálicos, não metálicos e compósitos, sen
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Fatigue failure analysis of HSLA steel sheets holed by conventional and flow drilling processes
RESUMO O processo de furação por escoamento produz buchas para uniões removíveis que podem ser roscadas pelo processo de rosqueamento por conformação, reduzindo etapas da produção de componentes da indústria automobilística e em galpões da construção civil. Aços de alta resistência e baixa liga (ARBL) são empregados em variadas aplicações n
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Fatigue failure analysis of HSLA steel sheets holed by conventional and flow drilling processes
ABSTRACT Flow drilling process produces bushes for removable joints that can be threaded by forming tapping process, reducing stages in production of components of automobile industry and in construction sheds. High strength and low alloy steels (HSLA) are employed on several applications in the processing industry. Benefits provided by these materials make
Matéria (Rio J.). Publicado em: 10/06/2019
-
7. Experimental studies of short concrete reinforced steel fiber beams under bending
Resumo Este estudo apresenta os resultados do rompimento de dois grupos de vigas de concreto com fibras de aço. Cada grupo foi composto de 4 vigas com vão de 300 mm, 4 com vão de 500 mm e 4 com vão de 800 mm e seção de 15 cm x 15 cm. A variação dos grupos se deu pela quantidade de fibras (I com 40 kg/m³ e II com 60 kg/m³). Foram avaliados o comport
Rev. IBRACON Estrut. Mater.. Publicado em: 20/05/2019
-
8. Cyclic fatigue resistance of novel Genius and Edgefile nickel-titanium reciprocating instruments
Abstract: This study aimed to assess the cyclic fatigue resistance of Genius and EdgeFile X1 reciprocating instruments compared with WaveOne Gold Primary. Twenty Genius (Ultradent) 25.04, 20 Genius 30.04, 20 EdgeFile X1 (EdgeEndo) and 20 WaveOne Gold Primary (Dentsply Maillefer) instruments were included in this study and tested in a static cyclic fatigue te
Braz. oral res.. Publicado em: 11/04/2019
-
9. Two-Dimensional Numerical Model of the Fracture Process in Steel Fibre Reinforced Concrete with the Continuum Strong Discontinuity Approach and Functional Data Analysis
Abstract This paper presents the formulation of a two-dimensional numeri-cal model able to describe the fracture process in structural mem-bers of steel fibre reinforced concrete (SFRC) from the volume ratio of the fibres and the mechanical properties of the compo-nents: a concrete matrix and a set of steel fibres with a random orientation. The relationship
Lat. Am. j. solids struct.. Publicado em: 08/04/2019
-
10. Volume and/or Time of NaOCl Influences the Fracture Strength of Endodontically Treated Bovine Teeth
Resumo O objetivo desse estudo foi o de avaliar se o aumento de volume e/ou tempo de contato do NaOCl afeta a resistência à fratura de dentes bovinos tratados endodonticamente. Quatro incisivos bovinos de 10 animais foram alocados em 4 grupos usando um desenho experimental de boca dividida. Os canais radiculares foram instrumentados usando uma sequência d
Braz. Dent. J.. Publicado em: 2019-02
-
11. Investigation of Stress Corrosion Cracking of Austenitic, Duplex and Super Duplex Stainless Steels under Drop Evaporation Test using Synthetic Seawater
Abstract Stress corrosion cracking (SCC) of UNS S31603 austenitic stainless steel (ASS), UNS S32205 duplex stainless steel (DSS) and UNS S32750 super duplex stainless steel (SDSS) was investigated. SCC tests were carried out at 110 ºC for 500 h under drops of synthetic seawater (DET, drop evaporation test). Two loading conditions were investigated: 50 % and
Mat. Res.. Publicado em: 31/01/2019
-
12. Nickel-Titanium Alloys Welding of Thin Sheets Using GTAW: Comparative Study Between Similar and Dissimilar Welding with AISI 304 Stainless Steel
The objective of the present work was to evaluate welding of thin sheets (thickness < 1 mm) of similar and dissimilar NiTi alloys with AISI 304 stainless steel using the Gas Tungsten Arc Welding (GTAW) process and to study the mechanical and metallurgical properties of the joints with and without post-welding heat treatment (PWHT). The GTAW process was chose
Mat. Res.. Publicado em: 08/11/2018