Metal Furnace
Mostrando 1-12 de 50 artigos, teses e dissertações.
-
1. The importance of education
Abstract The present research is dedicated to analyzing the addition of sawdust biomass, which is a carbonaceous raw material that may be used in coal blends for the production of metallurgical coke, preserving the required quality, with lower cost. The quality of metallurgical coke may be determined by the efficiency of its chemical, physical and thermal fu
REM, Int. Eng. J.. Publicado em: 2021-06
-
2. Quality evaluation of metallurgical coke produced with sawdust and different mixtures of coal
Abstract The present research is dedicated to analyzing the addition of sawdust biomass, which is a carbonaceous raw material that may be used in coal blends for the production of metallurgical coke, preserving the required quality, with lower cost. The quality of metallurgical coke may be determined by the efficiency of its chemical, physical and thermal fu
REM, Int. Eng. J.. Publicado em: 2021-06
-
3. AVALIAÇÃO DE NANOTUBOS DE CARBONO FUNCIONALIZADOS VISANDO O DESENVOLVIMENTO DE MÉTODOS DE PRÉ-CONCENTRAÇÃO DE ÍONS METÁLICOS E DETERMINAÇÃO POR TÉCNICAS ESPECTROMÉTRICAS E ELETROANALÍTICAS
This review focuses on the use of functionalized carbon nanotubes (CNTs) on the development of preconcentration methods with substantial contributions on selectivity and sensitivity for metal ions determination. CNTs have been usually employed in the development of preconcentration/speciation coupled to spectroanalytical techniques for ions determination at
Quím. Nova. Publicado em: 2020-09
-
4. PREPARATION AND SIMULATION OF THE ON-LINE SiO2/S COATING FOR COKING INHIBITION IN THE INDUSTRIAL CRACKING FURNACE
Abstract Coke formation inside radiant coils is one of the main problems during thermal cracking of hydrocarbons. The on-line preparation of the coating for coking inhibition is a promising technology because it provides more flexibility to the operators on site. The SiO2/S coating was prepared on the inner surface of coils in an 8-year-served GK-VI industri
Braz. J. Chem. Eng.. Publicado em: 13/01/2020
-
5. Fundente para Recargue por Soldadura con Arco Sumergido a Partir de Ferrocromo-manganeso y Escoria de la Reducción Simultánea de Cromita y Pirolusita
Abstract The obtaining of a flux for hardfacing by Submerged Arc Welding (SAW), using ferrochrome-manganese and slag obtained from the simultaneous carbothermal reduction of chromite and pyrolusite is addressed. The ferrochrome-manganese and the slag were obtained, conceiving that both products satisfy the requirements of the components (alloy system and ma
Soldag. insp.. Publicado em: 24/10/2019
-
6. Solidification Furnace Developed for Sounding Rockets: Rio Verde Mission
ABSTRACT Brazil has a Microgravity Program mainly based on experiments using sounding rockets. Up to now, four missions have been carried out with approximately 35 experiments submitted in total. In all flights, the Associate Laboratory of Sensors and Materials of the Brazilian Space Research Institute (LABAS/INPE) participated with a fast solidification fur
J. Aerosp. Technol. Manag.. Publicado em: 03/06/2019
-
7. Combustibility behavior of PCI coals, green petroleum coke and charcoal fines used as fuel for injection into blast furnace tuyeres
Abstract Pulverized coal injection (PCI) into blast furnace tuyeres is widely used by integrated steel mills worldwide to reduce the consumption of coke and costs. High injection rates are desirable. The big challenge is to achieve them with cheaper and lower quality raw materials, without losing the quality of the hot metal and the productivity of the blast
REM, Int. Eng. J.. Publicado em: 2019-03
-
8. Selection of materials for blast furnace injection using quality indicators
Abstract The injection of pulverized materials is a technique used in most of the blast furnaces in the world to reduce coke and charcoal consumption. In addition, injection is one of the main variables of the blast furnace heat control. Coal is the most used material for the injection, but some industries have been attempting to use other materials, usually
REM, Int. Eng. J.. Publicado em: 2019-03
-
9. Study on Effect of EAFD Particulate Reinforcement in AA7075 Aluminum Matrix Composites
Eletric arc furnace dust is dangerous solid waste that is generated in steel manufacturing processes. The utilization of the dust from these industries avoids disposing it into industrial waste landfills and saves costs. In this study, an attempt has been made to fabricate aluminum matrix composites reinforced with EAFD particulate, throught the conventional
Mat. Res.. Publicado em: 13/09/2018
-
10. Manufacturing of Cu-Sn foams through SDP
ABSTRACT This work reports the processing of bronze foams manufactured by using the powder metallurgy method known as Sintering Dissolution Process. During the sintering step, a device with controlled atmosphere separated from the heating furnace was employed to avoid the quick oxidation of metal particles. The device allows to control its internal atmospher
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Carbon based DLC films: Influence of the processing parameters on the structure and properties
ABSTRACT Hydrogenated carbon-based films, such as DLC (“Diamond Like Carbon”), have interesting properties such as excellent tribological behavior, low friction coefficient, high superficial hardness and good wear resistance; they are chemically inert and highly corrosion resistant. They are deposited by means of PACVD (plasma-assisted chemical vapor dep
Matéria (Rio J.). Publicado em: 19/07/2018
-
12. Carbothermic reduction of Electric Arc Furnace Dust via thermogravimetry
Abstract Electric Arc Furnace Dust (EAFD) is a solid waste originated from electric steelmaking furnaces. Currently, according to some authors, there is an estimated generation of 15 to 25 kg of dust per ton of steel produced. The formation of the dust is related to the following steps of the process: furnace charge, metal volatilization, iron vaporization u
REM, Int. Eng. J.. Publicado em: 2018-07