Metal Furnace
Mostrando 13-24 de 50 artigos, teses e dissertações.
-
13. Copper/Iron Brake Friction for Military Aircraft Application
ABSTRACT: The present study assesses the influence of non-metallic constituents and manufacturing parameters, such as compaction pressure and sintering temperature, to produce a metal matrix composite (MMC) of copper/iron, based on the brake disc of aircraft AT-29 SuperTucano. The samples were produced with six different compositions, by varying the amount o
J. Aerosp. Technol. Manag.. Publicado em: 03/05/2018
-
14. Evaluation of recycled MgO-C bricks and dead-burned dolomite fines in setting slag foaming in the electric arc furnace
Abstract Production cost reduction for the Electric Arc Furnace (EAF) technology is strongly dependent on the efficiency of the electrical energy being introduced into the metal bath. Besides EAF technology, the slag foaming process is currently applied to some other equipment for steel production aiming to save energy, productivity improvements, enhance the
REM, Int. Eng. J.. Publicado em: 2018-03
-
15. Influence of casting heterogeneities on microstructure and mechanical properties of austempered ductile iron (ADI)
ABSTRACT An investigation was carried out to examine the influence of as-cast heterogeneities on the resulting microstructure and mechanical properties of an austempered ductile cast iron (ADI). A commercial hypereutectic ductile iron alloy with 3.59% C, 2.68% Si, 0.24% Mn and 0.46% Cu (in wt. %) was produced in a coreless induction furnace. The specimens we
Matéria (Rio J.). Publicado em: 10/08/2017
-
16. Blast Furnace Hearth Lining: Post Mortem Analysis
The main refractory lining of blast furnace hearth is composed by carbon blocks that operates in continuous contact with hot gases, liquid slag and hot metal, in temperatures above 1550 ºC for 24 hours a day. To fully understand the wear mechanism that acts in this refractory layer system it was performed a Post Mortem study during the last partial repair o
Mat. Res.. Publicado em: 15/05/2017
-
17. Annealing effects on the structural and optical properties of vanadium oxide film obtained by the hot-filament metal oxide deposition technique (HFMOD)
ABSTRACT Vanadium oxide films amorphous, nonstoichiometric and highly absorbing in the optical region were deposited on ITO-coated glass and on silicon substrates, by the hot-filament metal oxide deposition technique (HFMOD) and oxidized by ex-situ annealing in a furnace at 200, 300, 400 and 500 ºC, under an atmosphere of argon and rarefied oxygen. X-ray di
Matéria (Rio J.). Publicado em: 11/05/2017
-
18. Effect of Cryogenic Chill on Mechanical Properties of ASTM A 494 M Grade Nickel Based Alloy Metal Matrix Composites
An investigation in the present research was made to fabricate and evaluate the microstructure and mechanical properties of metal matrix composites developed using cryogenically cooled copper chills, consisting of ASTM A 494 M grade nickel alloy matrix and garnet particles as the reinforcement. The particle's amount added ranges from 3 wt. % to 12 wt. % in s
Mat. Res.. Publicado em: 26/09/2016
-
19. Effect of Mill Type on Morphology of AA6013 Aluminium Powder
ABSTRACT In conventional recycling method, metal chips are cast after pressing and melting in electric arc furnace. Material loss occurs during the recycling from liquid metal due to the several reasons. Direct recycling method which produces the aluminium powder from aluminium chips using mechanical mill can be an alternative to conventional recycling metho
Matéria (Rio J.). Publicado em: 2016-09
-
20. Agarose Based Magnetic Solid-Phase Extraction-Magnetic Field Agitation for Determination of Trace Amounts of Molybdenum in Beans
A magnetic solid-phase extraction method based on agarose coated magnetic nanoparticles (ACMNPs) coupled to a magnetic field agitation (MFA) device was developed and used for the preconcentration and graphite furnace atomic absorption spectrometric determination of trace amounts of MoVI in beans. The formation of the nanoparticles and their encapsulation in
J. Braz. Chem. Soc.. Publicado em: 2016-04
-
21. Adjusting the Sintering Cycle of a Hadfield Sintered Steel Produced by Metal Injection Molding
Processing of high manganese austenitic sintered steels present several challenges concerning thermodynamic reactions that occur during the sintering of these materials such as Mn oxidation, sublimation and even the formation of liquid phases or undesired compounds, e.g. grain boundary carbides. Therefore it is extremely important to adjust the sintering par
Mat. Res.. Publicado em: 17/11/2015
-
22. Caracterización de semielaborados de aleaciones de titanio procesadas por extrusión y laminación perforación (proceso Mannesmann)
ABSTRACTFor the manufacture of seamless pipes and tubes are used, as raw materials, hollow bars from hot deformation processes like extrusion and rotary tube piercing (Mannesmann process). Starting from these semi-elaborated products and by means of successive cross sections reductions through tube drawing or tube rolling (cold pilgering) the requested final
Matéria (Rio J.). Publicado em: 2015-09
-
23. Metalloproteomic Profile Determination of Muscle Samples from Nile Tilapia (Oreochromis niloticus) Using AAS and ESI-MS/MS after 2D-PAGE Separation
This study evaluated the metalloproteomic profile of muscle tissue samples from Nile tilapia (Oreochromis niloticus). Two-dimensional polyacrylamide gel electrophoresis (2D-PAGE) methods was used for protein fractionation and identification based on image analysis. Determination of Ca, Cu, Fe, Mn and Zn was performed in the protein spots by flame and/or grap
J. Braz. Chem. Soc.. Publicado em: 2015-02
-
24. Otimização e comparação de processos para formação do campo retrodifusor com boro em células solares
The aim of this thesis was to develop and compare methods for the formation of the back surface field and emitter with boron using n-type and p-type solar-grade Si-Cz wafers as well as analyze and optimize a manufacturing process of solar cells with structure n+pp+ and back surface field formed by boron. The highly doped p+ region was formed by spin-on depos
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/03/2012