Computational Geometry
Mostrando 13-24 de 128 artigos, teses e dissertações.
-
13. Diseño, simulación y análisis del proceso de extrusión de un perfil termoplástico en PVC rígido para optimizar el diseño de la matriz y los parámetros
ABSTRACT The objective of the present work was to verify and optimize the die design to manufacture a thermoplastic profile in rigid PVC using the simulation of the flow in the mentioned matrix through the use of Computational Fluid Dynamics (CFD) and through tests in extrusion, using an experimental calibrator, the required geometry and dimensions were obta
Matéria (Rio J.). Publicado em: 19/07/2018
-
14. Direct Numerical Simulation of a Compressible Flow and Matrix-Free Analysis of its Instabilities over an Open Cavity
ABSTRACT: This study takes a Jacobian-free approach based on the Arnoldi iteration to present a method to perform hydrodynamic instability analysis based on Direct Numerical Simulations. The method employs high order spatial and temporal discretizations for the flow simulation and has very low requirements of computational time and memory, compared to conven
J. Aerosp. Technol. Manag.. Publicado em: 19/07/2018
-
15. INIBIÇÃO À CORROSÃO DE AÇO-CARBONO EM MEIO SALINO PELO HETEROCICLO ISATINA VEICULADO EM MICROEMULSÕES
Polar microemulsion systems (SME) based on saponified coconut oil (OCS) as surfactant were prepared in order to increase the solubility of the heterocycle isatin (IST) aiming at its application as corrosion inhibitor against AISI 1020 mild steel, in saline medium. The adsorptions phenomena of the tested SME systems (SME-OCS1-IST and SME-OCS2-IST) in the liqu
Quím. Nova. Publicado em: 2017-08
-
16. How Accurate is the SMD Model for Predicting Free Energy Barriers for Nucleophilic Substitution Reactions in Polar Protic and Dipolar Aprotic Solvents?
In the past seven years, the SMD (Solvent Model Density) method has been widely used by computational chemists. Thus, assessment on the reliability of this model for modeling chemical process in solution is worthwhile. In this report, it was investigated six anion-molecule nucleophilic substitution reactions in methanol and dipolar aprotic solvents. Geometry
J. Braz. Chem. Soc.. Publicado em: 2016-11
-
17. Computational Fluid Dynamics (CFD) simulating heated air from wood burning inside a poultries barn
ABSTRACT Animal welfare is essential for livestock yield gains, which has been ethically justifiable and socially acceptable. Thus, our research aimed to test computational fluid dynamics model (CFD) to simulate heated air within a poultry barn. Data were simulated in CFD software based on Navier-Stokes equations (geometry of 3 m x 6 m, considering a symmetr
Eng. Agríc.. Publicado em: 2016-10
-
18. Tip Deflection Determination of a Barrel for the Effect of an Accelerating Projectile Before Firing Using Finite Element and Artificial Neural Network Combined Algorithm
Abstract For realistic applications, design and control engineers have limited modelling options in dealing with some vibration problems that hold many nonlinearity such as non-uniform geometry, variable velocity loadings, indefinite damping cases, etc. For these reasons numerous time consuming experimental studies at high costs must be done for determining
Lat. Am. j. solids struct.. Publicado em: 2016-10
-
19. Geometry and head loss in Venturi injectors through computational fluid dynamics
ABSTRACT To determine the influence of geometry on the hydrodynamic behavior of Venturi injectors, using computational fluid dynamics techniques, we studied, at the Universitat Politècnica de València, Valencia, Spain, the geometric parameters that exert the most influence on head losses: the relationship between throat diameter and nozzle (β), nozzle ang
Eng. Agríc.. Publicado em: 2016-06
-
20. A Computational Protein Structure Refinement of the Yeast Acetohydroxyacid Synthase
A combined molecular modeling and molecular dynamics simulation was carried out to obtain an improved description of the yeast acetohydroxyacid synthase (AHAS) in aqueous solution. After a thorough homology modeling, the AHAS catalytic dimer was subjected to a molecular dynamics (MD) simulation to analyze its behavior and optimize its geometry. The AHAS 3
J. Braz. Chem. Soc.. Publicado em: 2015-08
-
21. Potencialidades computacionales del Método de los Elementos Finitos para la modelación y simulación de materiales compuestos: revisión
This work presents a review of computational models that use the Finite Elements Method (FEM) for the study of composite materials mechanical behavior, focusing the analysis in materials reinforced by particles or fibers. Bibliographic analysis shows that using FEM it is possible to successfully estimate the effect on the composites mechanical properties, of
Matéria (Rio J.). Publicado em: 2015-06
-
22. Two-parameter Rigid Block Approach to Upper Bound Analysis of Equal Channel Angular Extrusion Through a Segal 2θ-die
This article deals with a phenomenological description of experimentally determined complex geometric shape of material dead zone during Equal Channel Angular Extrusion (ECAE) through a Segal 2θ-die with a channel intersection angle of 2θ>0°and 2θ<180°. Taking into account the complex dead zone geometry in a 2θ-die, a two-parameter Rigid Block Method (
Mat. Res.. Publicado em: 2015-06
-
23. Diseño y predicción del funcionamiento de inyectores Venturi en riego localizado
The design and prediction performance of four Venturi injector prototypes have been studied using Computational Fluid Dynamics (CFD) techniques. Results were compared with experimental tests carried out in the laboratory of the Universitat Politècnica de València, Valencia, Spain. The analysed and selected geometries for each prototype were used to simulat
Rev. bras. eng. agríc. ambient.. Publicado em: 2014-12
-
24. 2D upper bound analysis of ECAE through 2θ-dies for a range of channel angles
Equal Channel Angular Extrusion (ECAE), sometimes referred to as Equal Channel Angular Pressing (ECAP), is a Severe Plastic Deformation technique. However the energy-power parameters of ECAE have not been fully addressed in previous known publications. The present article is focused on the punching pressure, accumulated plastic strain, and dead metal zone ge
Mat. Res.. Publicado em: 26/10/2014