Bending Resistance
Mostrando 1-12 de 100 artigos, teses e dissertações.
-
1. Optimum design of steel columns filled with concrete via genetic algorithm: environmental impact and cost analysis
Abstract The use of concrete-filled tubular columns as part of structural systems has steadily increased throughout the years. The growing demand for structural elements of this nature is a direct result of the possibility to use various cross-section shapes that have increased strength, along with resistance to fire and other corrosive agents. The main obje
REM - International Engineering Journal. Publicado em: 2022
-
2. Análise da resistência de placas ósseas de acrílico fabricadas a laser quando submetidas a diferentes forças que agem sobre o foco de fratura
RESUMO Objetivou-se com este trabalho analisar a resistência de placas ósseas de acrílico, confeccionadas com cortadora a laser CO2, quando submetidas às forças que agem sobre o foco de fratura. Foram utilizados 40 fêmures de ovinos (Ovis aries) e confeccionadas 40 placas de acrílico, os quais foram avaliados em grupos: grupo OP - foram avaliados 20 o
Arq. Bras. Med. Vet. Zootec.. Publicado em: 13/12/2019
-
3. Evaluation of the stiffening mechanism based on micro-sized particle inclusions in laminated composites
Rigid particles have been incorporated into laminated composites, especially to enhance their bending performance attributed to the stiffening of the matrix phase (i) and the increased interlaminar shear resistance (ii). In order to better evaluate the improvement mechanism provided by the particulate inclusions, this work investigates the incorporation of m
Mat. Res.. Publicado em: 17/10/2019
-
4. Flexural behavior of hybrid GFRP - concrete railway sleepers
Resumo Este trabalho tem por objetivo apresentar o comportamento à flexão de vigas híbridas de GFRP (glass fiber reinforced polymer - polímero reforçado com fibra de vidro) e concreto para aplicação em dormentes ferroviários. Pretendeu-se obter dormentes com adequada resistência mecânica, não susceptíveis à corrosão, duráveis e mais leves que
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
5. Aço de alta dureza para aplicação balística: propriedades mecânicas
RESUMO Blindagens balísticas são projetadas a resistir determinadas ameaças, que dependem da aplicação. Estas ameaças podem ser geradas por projéteis de armas de fogo ou estilhaços provenientes de explosões com diferentes energias cinéticas. Os materiais normalmente utilizados para este propósito são metálicos, não metálicos e compósitos, sen
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Beam-Column Joints Reinforcement Detailing Adequacy in Case of a Corner Column Loss-Numerical Analysis
Abstract This study investigates the behavior of reinforced concrete (RC) beam-column joints at the corner panel after a ground corner column loss scenario. The ductility of a frame is dependent on the ductility of its components, particularly its joints. Deficiency in joints performance can be related to an unexpected event. For example, the removal of a gr
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
7. Biomechanical development and evaluation of a new framework for all-on-four rehabilitation
Resumo Introdução Para reabilitação de mandíbulas totalmente edêntulas, a opção por carga imediata determina a utilização de próteses provisórias que esplintem os implantes instalados. Apesar de provisórias com reforço proverem as reabilitações com benefícios biomecânicos, a não adoção desta indicação coexiste em diferentes estudos so
Rev. odontol. UNESP. Publicado em: 29/07/2019
-
8. The effect of concentrated transversal force on the moment resistance of rectangular hollow steel section beams
Abstract This article reports on a preliminary investigation about the effect of concentrated transversal force on the bending moment resistance of rectangular hollow steel section (RHS) beams. Two six-meter-long specimens with yield strength of 300 MPa and cross-section size of 250×150×6.4 mm were subjected to bending tests using a four-point load configu
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
9. Experimental studies of short concrete reinforced steel fiber beams under bending
Resumo Este estudo apresenta os resultados do rompimento de dois grupos de vigas de concreto com fibras de aço. Cada grupo foi composto de 4 vigas com vão de 300 mm, 4 com vão de 500 mm e 4 com vão de 800 mm e seção de 15 cm x 15 cm. A variação dos grupos se deu pela quantidade de fibras (I com 40 kg/m³ e II com 60 kg/m³). Foram avaliados o comport
Rev. IBRACON Estrut. Mater.. Publicado em: 20/05/2019
-
10. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
ABSTRACT Nickel-based weld overlays (cladding) are commonly used in oil & gas industry to extend the life of equipment under corrosive environment, as it improves the corrosion resistance without a significant increase in the manufacturing cost, when compared to a full nickel-based alloy equipment. Although there are extensive literature involving overlays a
Matéria (Rio J.). Publicado em: 20/05/2019
-
11. Desenvolvimento de uma máquina para ensaio de fadiga por flexão
RESUMO O conhecimento acerca das propriedades mecânicas dos materiais é de grande importância para aplicações de engenharia. O estudo dessas propriedades é necessário para o desenvolvimento de novos equipamentos ou produtos e uma importante propriedade é a resistência à fadiga. O objetivo deste trabalho é apresentar o projeto e construção de uma
Matéria (Rio J.). Publicado em: 20/05/2019
-
12. Mechanical and Microstructural Properties of Redispersible Polymer-Gypsum Composites
Studies on gypsum modified by polymers have been conducted to assess the potential of improvement in the mechanical performance, water resistance and increasing the setting time, facilitating its handling. Gypsum-based compounds made with different additions of redispersible polymers were studied, such as: ethylene-vinyl acetate (EVA), vinyl acetate terpolym
Mat. Res.. Publicado em: 25/04/2019