Alloying Elements
Mostrando 1-12 de 48 artigos, teses e dissertações.
-
1. Morphology, Crystalline Structure and Chemical Composition Of MAO Treated Ti-15Zr-Mo Surfaces Enriched with Bioactive Ions
In this study, MAO treatment was used to enrich, with bioactive Ca, Mg and P atoms, as-casted and heat-treated Ti-15Zr-xMo (x = 0, 5, 10 and 15 wt%) alloys, for potential use as advanced metallic biomaterials. The chemical composition of the surface was evaluated by EDS and XPS measurements. The morphology and microstructure was analyzed by OM and SEM images
Mat. Res.. Publicado em: 09/12/2019
-
2. Obtaining Composites Powders of Al2 O3 / Ni and Al2 O3 / Nb by Mechanical Alloying
Mechanical alloying (MA) can be highlighted among the various methods and powder processing forms, which consists of producing homogeneous materials from elementary powders. This process is of paramount importance as it has the ability to reduce the particle size of the powders and can often promote bonding between elements which have low interaction and wet
Mat. Res.. Publicado em: 14/10/2019
-
3. Effect of Squeeze Casting on Microhardness and Microstructure of Al-3Cu-xSi Alloy
Aluminum alloys of the ANSI series 319 present Si and Cu as the main alloying elements and the mechanical strength of these alloys can be improved by the precipitation of the metastable Al2Cu phase. Squeeze Casting is a casting process in which the cast metal is deposited in a metal mold and solidified under certain pressure exerted by a punch. This process
Mat. Res.. Publicado em: 30/09/2019
-
4. Influence of High Current-Density Impulses on the Stress-Strain Response and Microstructural Evolution of the Single Crystal Superalloy CMSX-4
Owing to the low formability of single-crystal nickel-based materials, single-crystal components are typically cast. Subsequently, a multi-stage heat treatment is carried out in order to partially compensate the dendrite segregation and to stabilize the precipitated γ’-phase. Such components possess a high resistance to creep at elevated temperatures. Sin
Mat. Res.. Publicado em: 22/10/2018
-
5. Effect of Hot Deformation on Microstructure, Hardness and Precipitation Kinetics in a C350 Maraging Steel Modified by Titanium Addition
Maraging steels are alloys with a good balance between strength and fracture toughness. These properties are obtained by quenching and aging treatments, where the precipitation of intermetallic compounds is promoted in a martensitic matrix. In this context, this paper aims to evaluate the effect of hot deformation on microstructure, kinetics and formation of
Mat. Res.. Publicado em: 17/09/2018
-
6. Efecto del tratamiento sub-cero sobre la microestructura y dureza de fundiciones blancas alto cromo
ABSTRACT The effect of the sub-zero treatment temperature on the transformation of retained austenite to martensite in two high chromium white cast irons (ASTM A532 Class II Type B) was studied. The sub-zero treatment applied to each alloy in the as cast condition was performed at -40, -65 and -180 ° C for 10 minutes; after the holding time was completed th
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Impact of Alloy Composition and Thermal Stabilization on Martensitic Phase Transformation Structures in CuAlMn Shape Memory Alloys
Alloys of CuAlMn are known as cheap, high strength shape memory alloys with an excellent damping capacity within their austenitic-martensitic phase transformation, compared to alloy systems like NiTi, CuZnAl or MnCu. But CuAlMn alloys have disadvantage due to generation of voids by a high shrinkage which further increases the existing proneness to stress cra
Mat. Res.. Publicado em: 19/07/2018
-
8. The Effect of Electroless Bath Parameters and Heat Treatment on the Properties of Ni-P and Ni-P-Cu Composite Coatings
Ni-P-(Cu) composite coatings were applied on a St37 steel in an acidic bath of hypophosphite composite. The effect of the concentration of the Cu particles and pH of the solutionon the amount of Ni and P of the coatings, their morphology, and hardness of the coatings were explored. Some of the coated samples were also heat treated at 400ºC for 1 hour. The p
Mat. Res.. Publicado em: 08/01/2018
-
9. Effect of the T6 Heat Treatment on Microhardness of a Directionally Solidified Aluminum-Based 319 Alloy
Aluminum alloys of the ANSI series 319 present Si and Cu as the main alloying elements and the mechanical strength of these alloys can be improved by the precipitation of the metastable Al2Cu phase during the ageing heat treatment. In this paper, the Al-5.5wt.%Si-3wt.%Cu alloy was elaborated and solidified in a water-cooled horizontal directional solidificat
Mat. Res.. Publicado em: 30/11/2017
-
10. Efecto del V y el Si Sobre la Microestructura de Depósitos Realizados con Electrodos Tubulares Revestidos de Alto Contenido de Mn (Hadfield)
Abstract: Fe-Mn-C (Hadfield) alloys for surfacing weld deposits have demonstrated excellent wear resistance under high dynamic loads. In recent years, numerous studies have been conducted to improve their wear resistance and performance through the introduction of others alloying elements. In the present work, microstructure and hardness of high Mn surfacing
Soldag. insp.. Publicado em: 09/10/2017
-
11. Influence of casting heterogeneities on microstructure and mechanical properties of austempered ductile iron (ADI)
ABSTRACT An investigation was carried out to examine the influence of as-cast heterogeneities on the resulting microstructure and mechanical properties of an austempered ductile cast iron (ADI). A commercial hypereutectic ductile iron alloy with 3.59% C, 2.68% Si, 0.24% Mn and 0.46% Cu (in wt. %) was produced in a coreless induction furnace. The specimens we
Matéria (Rio J.). Publicado em: 10/08/2017
-
12. Series of Nanocrystalline NiCoAlFe(Cr, Cu, Mo, Ti) High-Entropy Alloys produced by Mechanical Alloying
Abstract The mechanical alloying technique was employed to produce series of high entropy alloys, combining in equiatomic percentage Al, Co, Cr, Cu, Fe, Mo, Ni and Ti. Milling times were 0, 10, 20 and 30 h, and experiments were performed in a high energy ball mill (SPEX-8000M) under argon atmosphere. The structural and microstructural changes due to mechanic
Mat. Res.. Publicado em: 08/08/2016