Die Casting
Mostrando 1-12 de 15 artigos, teses e dissertações.
-
1. Glass Formation of Null-Matrix Cu-Hf-(Zr, Ti) Alloys
An approach following the null-matrix, Ti/Zr ratio of 2.08, for neutron diffraction was used to calculate the glass formation in Cu-Ti-(Hf,Zr) alloys. The Cu55Zr14.6Ti30.4, Cu61.48Hf18.52Zr6.48Ti13.52, Cu58.1Hf16.9Zr8.1Ti16.9 and Cu52.46Hf14.2Zr10.8Ti22.54 compositions (at. %), were calculated and prepared by argon arc melting. Copper die suction casting was
Mat. Res.. Publicado em: 13/01/2020
-
2. A tradução de Die Verneinung para o Português e uma nova hipótese
Os autores realizam, a partir da análise de diferentes versões e traduções do artigo freudiano Die Verneinung (1925), uma investigação sobre fundamentais termos e concepções empregados por Freud, possibilitando um novo exame sobre alguns fenômenos clínicos e impasses diagnósticos.(The translation of “Die Verneinung” into Portuguese and a new h
Rev. latinoam. psicopatol. fundam.. Publicado em: 29/07/2019
-
3. Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel
Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we inv
Mat. Res.. Publicado em: 21/08/2017
-
4. Aplicação do método de Taguchi para redução de porosidade de peças fundidas sob pressão
O processo de fundição sob pressão de alumínio tem se desenvolvido significativamente nas últimas décadas, ocupando um lugar de destaque na indústria por produzir componentes de engenharia inovadora. Dentre os problemas de qualidade deste processo, o mais recorrente é a porosidade causada por vários fatores, dentre eles os parâmetros do processo qu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/09/2012
-
5. Método multicriterial para seleção de processos de fundição de metais
O objetivo principal da tese foi desenvolver um método multicriterial de seleção de processos de fundição de metais (MMSPF) para fabricação de componentes, considerando-se critérios técnicos, ambientais e econômicos para ser aplicado nas fases iniciais do desenvolvimento do componente. O MMSPF é constituído pelos módulos de seleção técnica e
Publicado em: 2011
-
6. Estudo comparativo de estrutura/propriedades da liga A1-Si5-Cu3-Mg nos estados fundido e tixoconformado, para utilização em componentes de motores / Comparative study of structure-properties from A1-Si5-Cu3-Mg alloy by casting and thixoforged, for use in engine components
The goal of this work was the comparative study between the Al-Si5-Cu3-Mg alloy obtained by die casting and thixoforging, based on a commercial accessories bracket used in diesel engines. The die casting commercial part was characterized in terms of structure and mechanical properties, and the final sample obtained by thixoforging was characterized in the sa
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/07/2010
-
7. Effect of phosphate-bonded investments on titanium reaction layer and crown fit
This study analyzed the reaction layer and measured the marginal crown fit of cast titanium applied to different phosphate-bonded investments, prepared under the following conditions (liquid concentration/casting temperature): Rema Exakt (RE) - 100%/237°C, 75%/287°C, Castorit Super C (CS)-100%/70°C, 75%/141°C and Rematitan Plus (RP)- 100%/430°C (special
Brazilian Oral Research. Publicado em: 2010-06
-
8. Avaliação de colapso em pinos extratores aplicados a moldes de fundição sob pressão / Evaluation of collapse in extraction columns applied to die casting molds
O processo de fabricação por fundição é um método amplamente utilizado na indústria para a obtenção de componentes mecânicos diversos. Uma das modalidades de fundição que se pode destacar é a fundição sob pressão. Para esse tipo específico de processo, é imprescindível a utilização de pinos extratores para expulsar o produto para fora do
Publicado em: 2010
-
9. Evaluation of the use of die spacer over the marginal fit of casting copings of Ni-Cr, Ni-Cr-Be and commercially pure Titanium / Avaliação da adaptação marginal de copings metálicos fundidos em ligas de níquel-cromo, níquel-cromo-berílio e em titânio comercialmente puro em função da aplicação de espaçadores
The purpose of the study was to evaluate the effect of using die spacers on the marginal fit of Ni Cr (Verabond II) (VB II) and Ni-Cr-Be (Verabond) (VB) alloys and commercially pure Titanium (Tritan) (Ti-cp) casting copings by the lost wax technique. Using a metal master die, 135 Resin Added Extra Hard Type IV Stone were obtained for the fabrication of wax p
Publicado em: 2008
-
10. Internal adaptation of cast titanium crowns
As the adaptation of titanium crowns obtained by Rematitan Plus investment, specific for titanium, is not recognized to be suitable, this study evaluated the effect of the concentration of the specific liquid and the temperature of the mold of investments on the internal misfit of crowns cast on commercially pure titanium. Individual dies of epoxy resin were
Journal of Applied Oral Science. Publicado em: 2007-08
-
11. Films of post-consumer polypropylene composites for the support layer in synthetic paper
Composite films were studied as possible candidates for the central or support layer of synthetic paper in a multilayer structure. Recycled post-consumer polypropylene films were reinforced with inorganic fillers at various compositions and under several processing conditions, with the aim of optimizing the physical and mechanical properties of rigidity and
Polímeros. Publicado em: 2006-06
-
12. Avaliação da influência dos parâmetros do processo de fundição sob pressão sobre qualidade de uma peça injetada em liga de alumínio
This paper describes the results obtained in a study performed in partnership between LabFund/DEM/PGCEM/UDESC and the Departments of Industrial Engineering, of Control of the Quality and of Aluminum Die Casting of WEG Motors involving the combination of an experimental methodology DOE (Design of Experiments) and a commercial numeric applicative to investigat
Publicado em: 2005