Ultimate Stress
Mostrando 1-12 de 55 artigos, teses e dissertações.
-
1. The Concept of a Rupture Risk Envelope for the Cochleo-Saccular Membranes
Abstract Introduction Alterations in endolymphatic pressure have long been suspected of being associated with the development of endolymphatic hydrops and rupture of the membranous labyrinth. More recently, there has been a focus on how membrane mechanics might contribute to membrane rupture. This is suspected to involve the viscoelastoplastic properties of
International Archives of Otorhinolaryngology. Publicado em: 2022
-
2. Impacto nas Propriedades Mecânicas e Tensões Residuais do Material ASTM A572 Grau 50 Soldado por Arco Submerso com Alívio de Tensões Térmico
Resumo O aço ASTM A572 Grau 50 é utilizado na fabricação de conjuntos soldados para aerogeradores, por este motivo, a realização de alívio de tensões é de grande importância para correção dos impactos causados pelos processos de soldagem, bem como, o conhecimento das propriedades finais obtidas com a realização deste processo. O objetivo desse
Soldag. insp.. Publicado em: 02/12/2019
-
3. An Anchorage System for Enhanced Bond Behavior between Carbon Fiber Reinforced Polymer Sheets and Cracked Concrete
Abstract The contribution of CFRP wraps, as an anchorage system, to enhancing bond behavior between CFRP sheet and cracked concrete, was investigated. Thirty six concrete blocks (150 x 150 x 200 mm) were cast with 3ϕ12 mm steel bars embedded laterally at different spacing along the 200-mm-dimension. Half of the moist-cured blocks were subjected to a cyclic
Lat. Am. j. solids struct.. Publicado em: 05/09/2019
-
4. Optimized design of RC deep beams based on performance metrics applied to strut and tie model and in-plane stress conditions
Abstract Deep beams do not behave according to classical beam theory. The nonlinearity of strain distribution within these elements requires application of strut and tie models (STM) or other alternatives to evaluate the complex stress field. Although the design of these elements is a common task for structural engineers, limited research is found on assessi
Lat. Am. j. solids struct.. Publicado em: 22/08/2019
-
5. Fragmentation model for the tensile response of unidirectional composites based on the critical number of fiber breaks and the correction of the fiber-matrix interfacial strength.
Abstract A fragmentation model based on global load sharing (GLS) theory is developed to obtain stress-strain curves that describe the mechanical behavior of unidirectional composites. The model is named C N B + τ * because it is based on the Critical Number of Breaks model (CNB) and on the correction of the fiber matrix interfacial strength, τ *
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
6. ESTIMATION OF TENSILE STRENGTH PARALLEL TO GRAIN OF WOOD SPECIES
ABSTRACT According to the ABNT NBR 7190: 1997 standard, tensile strength of wood samples shall be defined as the ratio between the ultimate strength from a stress test and the specimen cross-sectional area (350 mm2). However, due to the complex wood anatomy and experimental difficulties, the fractured surface in tested samples are not perpendicular to the lo
Eng. Agríc.. Publicado em: 12/08/2019
-
7. On the mechanical behavior of an Al 7075 alloy deformed by asymmetrical and conventional rolling
ABSTRACT Samples of the Al 7075 naturally and artificially aged were processed by conventional and asymmetrical rolling with 5% of thickness reduction. The rolling processes were evaluated under room temperature and under warm condition (130°C). Mechanical properties were evaluated by uniaxial tensile and Vickers microhardness tests. Microstructure evolutio
Matéria (Rio J.). Publicado em: 20/05/2019
-
8. Efeito da Taxa de Resfriamento na Liga Ni80Cu20 via Dinâmica Molecular
RESUMO A simulação em Dinâmica Molecular (MD) é uma poderosa ferramenta para estudo de ligas amorfas nanométricas. Neste artigo, a MD foi empregada para o estudo da liga Ni80Cu20. As simulações foram realizadas com o código livre LAMMPS, em um sistema contendo 2.000 átomos com interação atômica dada pelo potencial de Finnis-Sinclair (EAM-FS). O a
Matéria (Rio J.). Publicado em: 20/05/2019
-
9. The effect of the austenite grain refinement on the tensile and impact properties of cast Hadfield steel
This paper studied the effect of the austenite grain refinement on the tensile and impact properties of a cast Hadfield steel (12 % Mn, 1.2 %C and 0.65 % Si). The austenite grain refinement was obtained by hafnium inoculation. Microstructural characterization showed that the Hf-refined cast Hadfield steel featured a grain size of 600 µm, while the non-refin
Mat. Res.. Publicado em: 02/08/2018
-
10. Experimental Multi-scale analysis of Carbon/Epoxy Composites Nano-Reinforced by Carbon Nanotubes/Multi-layer Graphene
Nano-size structures, nanotubes/multi-layer graphene (CNT/MLG), were dispersed into epoxy system by a combination of sonication and high shear mixing. To avoid CNT/MLG agglomeration, a non-covalent functionalization were performed using surfactants, CO890 - Polyoxyethylene (40) nonylphenyl ether and SDBS - sodium dodecyl benzene sulfonate. Raman spectroscopy
Mat. Res.. Publicado em: 22/01/2018
-
11. Influence of shear lag coefficienton circular hollow sections with bolted sleeve connections
Abstract The circular hollow sections (CHS) are being widely employed in steel structures around the world, increasing the development of new researches. This article proposes an innovative connection model for circular hollow sections that facilitates and reduces the assembly cost of hollow section structures. The proposed connection is a tube sleeve, used
REM, Int. Eng. J.. Publicado em: 2017-12
-
12. Tensile properties of novel carbon/glass hybrid thermoplastic composite rods under static and fatigue loading
ABSTRACT Novel carbon/glass hybrid thermoplastic composite rods have been developed consisting of a PAN-based carbon fiber, an E-glass fiber, and a thermoplastic matrix. Three types of hybrid rods with different carbon/glass ratios were then fabricated. The surface and cross-sectional morphologies of the hybrid rods were observed using a digital microscope.
Matéria (Rio J.). Publicado em: 20/07/2017