Two Fluid Simulation
Mostrando 1-12 de 117 artigos, teses e dissertações.
-
1. Atomization Characteristics of Droplet and Morphologies of Arc Sprayed Ni-Al Particles and Composition Coatings
Droplet atomization characteristics and its morphology in twin-wire arc sprayed (TWAS) Ni-Al were explored in depth. Both numerical model and theoretical method were built for calculating the process of the droplet deformation and breakup in air flow, which based on the standard k-ε model and the volume of fluid (VOF) dual-phase flow model. The atomization
Mat. Res.. Publicado em: 23/09/2019
-
2. SIMULATION OF THERMAL DECOMPOSITION IN AN OPEN CAVITY: ENTROPY ANALYSIS
ABSTRACT This paper presents a numerical analysis of entropy generation in a two-dimensional rectangular channel where the inlet flow undergoes thermal decomposition resulting from a chemical reaction. The model considered viscosity and thermal conductivity to be dependent of temperature. Irreversibility due to mass transport was included in the entropy gene
Braz. J. Chem. Eng.. Publicado em: 15/07/2019
-
3. Microstructure and Flight Behaviors of Droplet and its Solidification in Twin-Wire Arc Sprayed Ni-Al Composite Coatings
Droplet flight and solidification behaviors during twin-wire arc sprayed (TWAS) composite coatings were systematically investigated. Both theoretical model and numerical method were established for calculating the droplet deformation, breakup and solidification process in air flow based on the volume of fluid (VOF) dual-phase flow model jointed with the stan
Mat. Res.. Publicado em: 19/03/2018
-
4. Computational Investigation on the Effects of Two-Way Wing Morphing Strategy in the Critical Mach Number
ABSTRACT: The elasto-flexible wing morphing is an advanced methodology to achieve higher lift-to-drag (L/D) ratio for the subsonic wing configurations at the given flow conditions. The present article describes mechanisms of continuous morphing of a swept back wing for achieving effective delay in the critical Mach number (Mcr) distribution over the wing sur
J. Aerosp. Technol. Manag.. Publicado em: 08/03/2018
-
5. SIMULATION OF VENTILATION SYSTEMS IN A PROTECTED ENVIRONMENT USING COMPUTATIONAL FLUID DYNAMICS
ABSTRACT Computational simulations of mass and energy flow help in implementing alternative cooling systems in protected environments. The aim of this study was to model and simulate the interaction between external and internal environments of a protected environment by means of computational fluid dynamics (CFD) techniques and validate micrometeorological
Eng. Agríc.. Publicado em: 2017-06
-
6. TOWARD PREDICTIVE MODELS FOR ESTIMATION OF BUBBLE-POINT PRESSURE AND FORMATION VOLUME FACTOR OF CRUDE OIL USING AN INTELLIGENT APPROACH
Abstract Accurate estimation of reservoirs fluid properties, as vital tools of reservoir behavior simulation and reservoir economic investigations, seems to be necessary. In this study, two important properties of crude oil, bubble point pressure (Pb) and formation volume factor (Bob), were modelled on the basis of a number of basic oil properties: temperatu
Braz. J. Chem. Eng.. Publicado em: 2016-12
-
7. Application of optimization for improvement of the efficiency of louvered-fin compact heat exchangers
Abstract A few decades ago, the product development process was just based on a trial and error procedure, and the designer's experience. The need for a new way to design and manufacture more economical and sustainable products corroborates increasingly to a new vision of how to create new products for the benefit of society. Modern numerical tools allow gre
REM, Int. Eng. J.. Publicado em: 2016-09
-
8. Uncertainty analysis of a flexible rotor supported by fluid film bearings
AbstractThis paper is dedicated to the analyses of the effect of uncertain parameters on the dynamic behavior of a flexible rotor containing two rigid discs and supported by two fluid film bearings. A stochastic method has been extensively used to model uncertain parameters, i.e., the so-called Monte Carlo simulation. However, in the present contribution, th
Lat. Am. j. solids struct.. Publicado em: 2015-08
-
9. Three-dimensional simulation of liquid flow on a sieve tray under different inclinations
The fluid state on a sieve tray will change when the towers tilt under wind loads. A computational fluid dynamics (CFD) model was used to predict the flow patters and hydraulics on the tray under different inclinations. The gas and liquid phases are modelled with the volume-of-fluid (VOF) framework as two inmiscible phases. Several three-dimensional transien
Braz. J. Chem. Eng.. Publicado em: 2014-12
-
10. The effect of the inner cylinder rotation on the fluid dynamics of non-Newtonian fluids in concentric and eccentric annuli
Helical flow in an annular space occurs during oil drilling operations. The correct prediction of flow of drilling fluid in an annular space between the wellbore wall and the drill pipe is essential to determine the variation in fluid pressure within the wellbore. This paper presents experimental and CFD simulation results of the pressure drop in the flow of
Braz. J. Chem. Eng.. Publicado em: 2014-12
-
11. Simulation of the solidification in a channel of a water-cooled glass flow
A computer simulation study of a laminar steady-state glass flow that exits from a channel cooled with water is reported. The simulations are carried out in a two-dimensional, Cartesian channel with a backward-facing step for three different angles of the step and different glass outflow velocities. We studied the interaction of the fluid dynamics, phase cha
Braz. J. Chem. Eng.. Publicado em: 2014-12
-
12. Application of Computational fluid dynamic in aluminum refining through pneumatic injection of powders
Magnesium removal process from molten aluminum using particles of silica sand was studied from a hydrodynamic point of view using computational fluid dynamics (CFD). The gas-liquid flow was modeled by a model of the Euler type for both gas and liquid phase transport. Newton´s law of motion was used to describe the subsurface motion of injected solid particl
Mat. Res.. Publicado em: 2014-12