Transformation Parameters
Mostrando 1-12 de 237 artigos, teses e dissertações.
-
1. Assessment of Total Attenuation and Adaptive Scheme for Quality of Service Enhancement in Tropical Weather for Satellite Networks and 5G Applications in Nigeria
Abstract The dynamic weather condition is a major concern for optimum channel utilization in recent times, especially at higher frequencies with larger bandwidth for 5G applications. Over the years, rain-induced attenuation among the hydrometeors has been linked as the major cause of signal impairment especially at the frequency, f ≥ 10 GHz. However, when
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2021-06
-
2. Influence of sintering parameters on the microstructure and mechanical properties of nanosized 3Y-TZP ceramics
Abstract The fracture toughness of 3Y-TZP ceramics obtained from a nanocrystalline powder with an optimized microstructure and highly transformable tetragonal grains was investigated. Samples of ZrO2-3 mol% Y2O3 were sintered at temperatures between 1250 and 1400 °C, with isothermal holding times of up to 16 h. Samples sintered at 1250 °C exhibited relativ
Cerâmica. Publicado em: 2021-03
-
3. Ultrasound reference values for the calcaneus of children and adolescents at moderate altitudes in Peru
Abstract Objective: a) Establish reference values for bone parameters by using the speed of sound (SOS, m/s) of broadband ultrasound attenuation (BUA, dB/MHz) and establish a bone quality index (BQI = αSOS + βBUA) for children and adolescents living in a region of moderate altitude, b) compare bone parameters with an international standard (with different
J. Pediatr. (Rio J.). Publicado em: 2021-02
-
4. An Alternative to Avrami Equation
This paper proposes an alternative to the Avrami equation capable of describing whole transformation curves with significant fitting-correlations. The model bears physically meaningful parameters which permit considering the initial transformation kinetics independently from the subsequent microstructural evolution. Data of martensite, bainite, recrystalliza
Mat. Res.. Publicado em: 30/09/2019
-
5. Comparison of in vitro callus-cultures from transgenic maize AG-5011YG (MON810) and conventional near-isogenic maize AG-5011
Abstract MON810 is a genetically-modified (GM) maize (Zea mays) event commonly employed in insect-resistant GM maize hybrids. GM events obtained by biolistic transformation methods, such as MON810, are generated by insertion of a recombinant gene expression cassette in a random locus of the plant genome, and this process may cause emergent properties besides
Crop Breed. Appl. Biotechnol.. Publicado em: 01/08/2019
-
6. Effect of Processing Parameters on Hot Deformation Behaviour and Microstructural Evolution of PM Ti-5553 Alloy at a Moderate-high Strain Rate
Isothermal compression tests of Ti-5553 (Ti-5Al-5V-5Mo-3Cr) alloy, produced by a fast consolidation approach from blended elemental powder mixture, were performed on a Gleeble® 3800 thermal-physical simulator to investigate its hot deformation behaviour. The samples were compressed in a wide temperature range from 700 ºC to 1150 ºC and a moderate-high str
Mat. Res.. Publicado em: 10/06/2019
-
7. Prediction of Properties of Sclerolobium paniculatum and Qualea grandiflora Charcoal
ABSTRACT There is a lack of techniques for the rapid and accurate determination of wood quality for charcoal production with good energy characteristics. The association of NIR spectroscopy and important charcoal parameters allows the prediction of these characteristics. This is a fast method that does not require sample preparation before the reading. The
Floresta Ambient.. Publicado em: 14/02/2019
-
8. Impact of Alloy Composition and Thermal Stabilization on Martensitic Phase Transformation Structures in CuAlMn Shape Memory Alloys
Alloys of CuAlMn are known as cheap, high strength shape memory alloys with an excellent damping capacity within their austenitic-martensitic phase transformation, compared to alloy systems like NiTi, CuZnAl or MnCu. But CuAlMn alloys have disadvantage due to generation of voids by a high shrinkage which further increases the existing proneness to stress cra
Mat. Res.. Publicado em: 19/07/2018
-
9. Estabilidad de las fases U3Si5, USi2-x y USi2 al incorporar Al en solución. Experiencias de calorimetría diferencial de barrido
ABSTRACT U(Mo) alloys are being studied to be applied as a fuel for research and test reactors. When U(Mo) particles are dispersed in an Al matrix, it is known that an interdiffusion during fabrication process and / or irradiation. In this sense, irradiation tests have shown that this IL has a bad behavior under irradiation coming up the addition of Si to Al
Matéria (Rio J.). Publicado em: 19/07/2018
-
10. Movimiento de las interfases durante la solidificación horizontal de aleaciones estaño-zinc
ABSTRACT Solidification processing is one of the important routes to produce materials, especially metals and alloys. The parameters for the transformation from liquid to solid, such as the temperature gradient, the growth rate, the cooling rate, the interphase velocity, vary from process to process and in one process also as a function of time and space. Th
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Estudio de la cinética de la disolución de los barros residuales de las industrias borateras con soluciones de glicerina
ABSTRACT In this paper the dissolution kinetics of industrial boron wastes residual with glycerin solutions (C3H8O3), effluent from the biodiesel industry, with the aim of enhancing the utilization both wastes, were investigated. It is based on the complexation of boron with the polyol. The dissolution is carried out in a batch reactor at atmospheric pressur
Matéria (Rio J.). Publicado em: 19/07/2018
-
12. An Experimental Study of the Solidification Thermal Parameters Influence upon Microstructure and Mechanical Properties of Al-Si-Cu Alloys
Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties s
Mat. Res.. Publicado em: 18/06/2018