Stainless Steels
Mostrando 1-12 de 165 artigos, teses e dissertações.
-
1. Corrosion Resistance of Cu-Alloyed Precipitation Hardenable Duplex Stainless Steel ASTM A890 Grade 1B
Duplex stainless steels (DSS) are corrosion resistant alloys largely used in chemical and petrochemical industries. Some commercial DSS contain 0.5-1.0% copper addition to improve the corrosion resistance by reducing the corrosion rate in non-oxidizing environments. Higher copper addition (≥ 2%) can also hard by precipitation, especially when fine copper p
Mat. Res.. Publicado em: 07/11/2019
-
2. Influence of Molybdenum on Microstructure and Pitting Corrosion Behavior of Solution-Treated Duplex Stainless Steel in a Lithium Chloride Solution
With technological advances in the several areas of knowledge, the constant search for materials with characteristics that meet certain applications has been growing, especially in the chemical and petrochemical industries, where materials capable of withstanding the conditions of corrosion in aggressive environments are required. The aim of this paper was t
Mat. Res.. Publicado em: 24/10/2019
-
3. Effect of Sigma Phase Precipitated at 850 °C on Corrosion Behaviour of UNS S82441 Duplex Stainless Steel
ABSTRACT Duplex stainless steels (DSS) are alloys with binary microstructure consisting of ferrite (δ) and austenite (γ), combining high mechanical properties and corrosion resistance by pitting and stress corrosion, due to the two phases austenite/ferrite. However, the formation of secondary and intermetallic phases, during solidification processes, heat
Matéria (Rio J.). Publicado em: 16/09/2019
-
4. Avaliação da susceptibilidade de precipitação da fase sigma na soldagem do aço inoxidável duplex SAF2205
RESUMO A soldagem de aços inoxidáveis duplex é uma operação crítica, devido aos ciclos térmicos aos quais o material é submetido, que podem favorecer a precipitação de fases deletérias. Nesse contexto, objetivo dessa pesquisa é analisar a influência da energia de soldagem na susceptibilidade à formação de fase sigma no aço duplex SAF2205. As
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Corrosion Behavior of Austenitic Stainless Steels in CO2-Saturated Synthetic Oil Field Formation Water
The corrosion behavior of austenitic and superaustenitic stainless steels was investigated in carbon dioxide-saturated synthetic oil field formation water using cyclic polarization tests. In order to measure the effect of carbon dioxide pressure, the samples were also exposed in a pressurized medium containing carbon dioxide and synthetic air. For this purpo
Mat. Res.. Publicado em: 05/09/2019
-
6. Effect of Nitrogen Addition to Shielding Gas on Cooling Rates and in the Microstructure of Thin Sheets of Duplex Stainless Steel Welded by Pulsed Gas Tungsten Arc Welding Process
The effect of the nitrogen content in the shielding gas and its effect on temperature distributions at the welded zone of thin sheets of duplex stainless steel have been evaluated. The duplex stainless steels have many features due to unique microstructural combination of austenite and ferrite grains. The phase balance can be easily shifted depending on the
Mat. Res.. Publicado em: 26/08/2019
-
7. A Note on Parameter Identification of the AISI 304 Stainless Steel Using Micromechanical-Based Phenomenological Approaches
Austenitic stainless steels have largely been used in industrial equipment, architectural components and consumer items amongst others. Numerical simulation of manufacturing processes of such components and parts requires adequate hardening descriptions and accurate inelastic parameters. This work addresses these issues for the AISI 304 stainless steels base
Mat. Res.. Publicado em: 19/08/2019
-
8. Influence of the Solution-Treatment Temperature and Short Aging Times on The Electrochemical Corrosion Behaviour of Uns S32520 Super Duplex Stainless Steel
Sigma phase leads to deterioration of corrosion resistance of super duplex stainless steels (SDSS) and its volume fraction increases as the time which the materials is exposed in determined temperature increases. In the present study, the effect of the short aging time on the formation of the sigma phase and on the corrosion behavior of UNS S32520 SDSS at 3.
Mat. Res.. Publicado em: 15/08/2019
-
9. Microstructural Evolution Due to One Thermal Cycle in a Superduplex Stainless Steel ASTM A890/A890M - Grade 6A in the As-Weld and Post-Weld Heat Treatment Conditions
During welding of the superduplex stainless steels are exposed to thermal cycles, allowing precipitation of deleterious phases as well as unbalance as the ferrite and austenite phases. This work analyzed the microstructural changes taking place on a plate ASTM A890/A890M - grade 6A steel submitted to arc welding one welding of pass conducted on a flat surfac
Mat. Res.. Publicado em: 08/08/2019
-
10. Nitretação a plasma da junta soldada do aço inoxidável super duplex SAF 2507
RESUMO Os aços inoxidáveis superduplex (AISD) apresentam em sua microestrutura as fases ferrita e austenita, de modo a conciliar boas propriedades mecânicas e de resistência à corrosão. Estes materiais possuem grande aplicação na indústria de extração de petróleo e na petroquímica. Quando estão sujeitos a estas aplicações, os dutos de AISD so
Matéria (Rio J.). Publicado em: 20/05/2019
-
11. Simulação termodinâmica computacional de liga modelo de aço super ferrítico contendo 0,07% de boro
RESUMO Aços inoxidáveis super ferríticos são utilizados em equipamentos como trocadores de calor e torres de destilação que operam em condições extremas de temperatura, pressão e em ambientes contendo altas concentrações de cloretos, H2S e CO2, encontradas nas novas áreas de exploração de petróleo e gás na costa brasileira. Uma liga super fer
Matéria (Rio J.). Publicado em: 20/05/2019
-
12. Avaliação da Adição de Ti, Nb e (Ti+Nb) na Microestrutura e Susceptibilidade à Sensitização de Aços Inoxidáveis Ferríticos Submetidos à Soldagem TIG
Resumo Neste estudo, a microestrutura e a resistência à corrosão intergranular de aços inoxidáveis ferríticos com adições de Nb, Ti e (Ti+Nb) submetidos à soldagem TIG foram investigadas. A caracterização estrutural dos cordões de solda foi realizada através de microscopias óptica (MO) e eletrônica de varredura (MEV) e espectroscopia por energ
Soldag. insp.. Publicado em: 16/05/2019