Pullout Strength
Mostrando 1-12 de 37 artigos, teses e dissertações.
-
1. The Influence of Thread Tap Mismatch on Pedicle Screw Pullout Strength
Resumo Objetivo Nosso objetivo foi estudar a resistência à extração “in vitro” do parafuso SpineGuard/Zavation Dynamic Surgical Guidance Z-Direct (Parafuso DSG Guia Cirúrgico Dinâmico, SpineGuard Inc, Boulder, Colorado, USA), um parafuso projetado para ser inserido utilizando a técnica de inserção direta. Métodos Os parafusos DSG de 5,5 e 6,5
Revista Brasileira de Ortopedia. Publicado em: 2022
-
2. Fixation of the Anterior Ligament Graft at the Tibial Pole: Biomechanical Analysis of Three Methods
Resumo Objetivo Análise biomecânica comparativa da resistência da fixação tibial para reconstrução ligamentar com parafuso de interferência, comparada com parafuso do tipo poste com arruela, e com fixação associada entre os métodos (fixação híbrida). Métodos Foram utilizados 54 corpos de prova (tíbia suína e tendão digital bovino), que fo
Rev. bras. ortop.. Publicado em: 13/12/2019
-
3. PROPERTIES OF PARTICLEBOARD PANELS MADE OF SUGARCANE PARTICLES WITH AND WITHOUT HEAT TREATMENT
RESUMO O objetivo deste trabalho foi determinar as propriedades de painéis aglomerados confeccionados com partículas de bagaço de cana-de-açúcar in natura e aquecidas a 250 °C durante 5 minutos. Foram empregadas várias proporções de partículas na confecção dos painéis e as suas propriedades foram comparadas com as propriedades de um painel fabri
Rev. Árvore. Publicado em: 25/11/2019
-
4. Numerical approach of the steel-concrete bond behavior using pull-out models
ABSTRACT This paper deals with the analysis of monotonic loading behavior in pull-out tests. The main objective is to obtain a reliable numerical model to represent the steel-concrete bond behavior using previously obtained experimental results. The tests were performed in RILEM pull-out specimen using 10 mm steel bar and concrete with compressive strength o
Matéria (Rio J.). Publicado em: 10/06/2019
-
5. Bond between steel and concrete made with ceramic waste aggregate
Abstract The reduction of natural resources combined with a substantial increase in the generation of solid waste in large urban centers, justifies the search for methods of reusing the construction industry waste. The ceramic industry has a high disposal rate during the manufacturing, transportation and eventual replacement of its products. In this case, re
REM, Int. Eng. J.. Publicado em: 2019-03
-
6. INFLUENCE OF DIAMETER AND GEOMETRY IN THE TAPPING OF THE PILOT HOLE IN PEDICLE SCREWS
RESUMO Objetivo: Avaliar o torque de inserção e a força de arrancamento de cada parafuso com diferentes diâmetros e machos. Métodos: Foram utilizados no estudo blocos de poliuterano com orifício piloto de 2,7mm, sendo feito um grupo experimentais com 5 blocos sendo avaliado o torque de inserção com torquímetro e avaliado o arrancamento de cada par
Coluna/Columna. Publicado em: 2019-03
-
7. Evaluation of Live Cuttings Effect on Slope Stability
ABSTRACT The aim of this work was to evaluate the development of shrub live cuttings and their effect on slope stability. Vertical in situ pullout tests and measurements of Phyllanthus sellowianus shoots and roots of 2, 4, 6, 8, 10 and 14 months old were conducted. Stability analyses were conducted for slopes with planar and curved rupture surfaces and for
Floresta Ambient.. Publicado em: 10/12/2018
-
8. Experimental Investigation of Steel-Concrete Bond for Thin Reinforcing Bars
Abstract The steel-concrete bond is a fundamental property in reinforced concrete structures. Although there are several studies on the steel-concrete bond, few of them have evaluated the performance of reinforcing bars with diameters less than 10.0 mm, which includes 5.0, 6.3, and 8.0 mm diameters, which are normally used in reinforced-concrete elements. Th
Lat. Am. j. solids struct.. Publicado em: 2017
-
9. Does MTA affect fiber post retention in repaired cervical root canal perforations?
Abstract This study evaluated the effect of mineral trioxide aggregate (MTA) on the retention of fiber posts in repaired root canal perforations. Ten-millimeter post spaces were prepared in 60 endodontically treated bovine incisors. Root perforations were created in half of the root canals in the cervical area prior to being filled with white MTA-Angelus. Fi
Braz. oral res.. Publicado em: 14/06/2016
-
10. Mechanical Characterization of Composites Manufactured by RTM Process: Effect of Fiber Content, Strain Rate and Orientation
Abstract High performance composites are exposed to severe loading and environmental conditions. In this work, mechanical properties of Fiberglass Reinforced Polyester (FRP) manufactured by resin transfer molding were evaluated. The effect of the strain rate on mechanical properties under three quasi-static testing conditions, four fiber contents and several
Lat. Am. j. solids struct.. Publicado em: 2016-02
-
11. Particleboard manufactured from Tauari (Couratari oblongifolia) wood waste using castor oil based polyurethane resin
Several wood species from the Amazon region are used in the manufacture of furniture, which leaves behind large amounts of waste (slabs, sawdust, sanding dust and bark), thus causing serious environmental impacts. An interesting alternative for the use of these wastes is the manufacture of particleboards. However, few studies have focused on the behavior of
Mat. Res.. Publicado em: 18/02/2014
-
12. Adhesion strategy and early bond strengths of glass-fiber posts luted into root canals
This study investigated the effect of coinitiator solutions and self-adhesive resin cement on the early retention of glass-fiber posts. Cylindrical glass-fiber posts were luted into 40 incisor roots with different adhesion strategies (n = 10): SB2, Single Bond 2 + conventional resin cement (RelyX ARC); AP, Scotchbond Multipurpose Plus (SBMP) activator + prim
Braz. oral res.. Publicado em: 14/08/2012