Plane Curves
Mostrando 1-12 de 63 artigos, teses e dissertações.
-
1. Numerical analysis of soft soil improved with stone column technique
Abstract The present research aims to do a numerical study on the behavior of a test embankment reinforced with stone column spacing of 1.85 m in a square grid with an average diameter of 1.0 m and 11.35 m length. The case study investigated the work in a steel company (ThyssenKrupp), located in Santa Cruz, western region of Rio de Janeiro - Brazil, where a
REM, Int. Eng. J.. Publicado em: 2021-09
-
2. Dumbbell Shaped Microstrip Broadband Antenna
Abstract In this article, a dumbbell shaped microstrip broadband microstrip antenna with partial ground plane is presented, The overall dimension of the proposed antenna is 20 × 15 × 1.5 mm3 and is fabricated on FR4 substrate which has electrical permittivity of 4.3 and loss tangent of 0.025. FR4 is a low cost and easily available. The thickness of the sub
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2019-03
-
3. Numerical stress-life curves for the AISI 4340 steel using two sets of materials properties and different bi-axial stress ratios
Abstract Fatigue assessments by the more robust strain-based approach demand the determination of the local strain history from nominal stresses. For notched members, a cyclic constitutive relation, the stress concentration factor (SCF) and a strain concentration rule are used with this aim in some approximate solutions. The plastic part of the cyclic consti
Lat. Am. j. solids struct.. Publicado em: 29/10/2018
-
4. Relationship between Coffee Leaf Analysis and Soil Chemical Analysis
ABSTRACT: Research focused on adequate nutrition of plants is essential in modern coffee production to increase yield and develop more efficient management strategies with greater environmental and economic sustainability. The objectives of this study were to establish critical and optimal levels of soil fertility properties for high yielding Arabica coffee
Rev. Bras. Ciênc. Solo. Publicado em: 07/06/2018
-
5. Evaluation of scoliosis using baropodometer and artificial neural network
Abstract Introduction: One of the most recurrent pathologies in the spine is scoliosis. It occurs in the frontal plane and is formed by one or more curves in the spinal column. The scoliosis causes global postural misalignment in an individual. One of the modifications produced by postural misalignment is the way in which an individual distributes weight to
Res. Biomed. Eng.. Publicado em: 2017-06
-
6. Numerical Study on the Structural Performance of Steel Beams with Slant End-plate Connections
Abstract Thermal effects can be one of the most harmful conditions that any steel structure should expect throughout its service life. To counteract this effect, a new beam, with a capability to dissipate thermally induced axial force by slanting of end-plate connection at both ends, is proposed. The beam was examined in terms of its elastic mechanical behav
Lat. Am. j. solids struct.. Publicado em: 2016-07
-
7. Structure and Properties of Titanium Doped Tungsten Disulfide Thin Films Produced via the Magnetron Co-Sputtering DC Technique
ABSTRACT In this work, titanium doped tungsten disulfide thin films (WS2-Ti) were deposited on AISI 304 stainless-steel substrates using the magnetron co-sputtering DC technique. Films were produced with varying titanium-cathode power from 0 to 25 W. The titanium content of the WS2 structure was determined using energy dispersive spectroscopy (EDS), thereby
Matéria (Rio J.). Publicado em: 2016-06
-
8. Uniaxial near plane strain tensile tests applied to the determination of the FLC0 formabillity parameter
An alternative procedure for the determination of the FLC0 value, the limit strain value corresponding to the plane strain mode of the Forming Limit Curves (FLC), a critical parameter in the sheet formability analysis, is suggested and compared with conventional Nakazima simulation tests. The procedure was tested using two different materials: interstitial-f
Mat. Res.. Publicado em: 13/06/2014
-
9. Dinâmica não-linear e reagente limitante: um exemplo de bifurcação transcrítica
The nonlinear analysis of a general mixed second order reaction was performed, aiming to explore some basic tools concerning the mathematics of nonlinear differential equations. Concepts of stability around fixed points based on linear stability analysis are introduced, together with phase plane and integral curves. The main focus is the chemical relationshi
Quím. Nova. Publicado em: 2014
-
10. Modeling and analysis of waves in a heat conducting thermo-elastic plate of elliptical shape
Wave propagation in heat conducting thermo elastic plate of elliptical cross-section is studied using the Fourier expansion collocation method based on Suhubi's generalized theory. The equations of motion based on two-dimensional theory of elasticity is applied under the plane strain assumption of generalized thermo elastic plate of elliptical cross-sections
Lat. Am. j. solids struct.. Publicado em: 2014
-
11. Crescimento, estrutura e magnetismo de filmes ultrafinos de Ni depositados sobre Pd(100)
In this work, the growth mode, the structure and the magnetic behavior of ultrathin Ni films epitaxially grown over Pd(100) were investigated using in-situ experimental techniques ass RHEED, LEED, AES, MBE and MOKE, and ex-situ VSM. The objective was to study the influence of the stress induced by the lattice parameter mismatch of the materials (10,4%), the
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/02/2012
-
12. Determination of the numerical parameters of a continuous damage model for the structural analysis of clay brick masonry
Models based on the continuous damage theory present good responses in representing the nonlinear behavior of reinforced concrete structures with loss of strength and stiffness of the material. However, damage theory is rarely employed in the analysis of masonry structures and numerical simulations are currently performed mostly by Finite Element Method form
Mat. Res.. Publicado em: 23/10/2012