Particles Coating
Mostrando 13-24 de 90 artigos, teses e dissertações.
-
13. The influence of Nano-TiO2 and Nano-Al2O3 Particles in Silicate Based Electrolytes on Microstructure and Mechanical Properties of Micro Arc Coated Ti6Al4V Alloy
Ceramic oxide coatings were fabricated on Ti6Al4V alloy by micro arc oxidation (MAO) in silicate electrolytes, with nano-TiO2 and nano-Al2O3 and without nano-additives. Effects of nano additives on the structural and mechanical properties of the MAO coatings were analysed. The MAO coatings were investigated by scanning electron microscopy (SEM), Energy-Dispe
Mat. Res.. Publicado em: 18/06/2018
-
14. PREPARAÇÃO, CARACTERIZAÇÃO FÍSICO-QUÍMICA E LIBERAÇÃO CONTROLADA DE MICROPARTÍCULAS DE GALACTOMANANA CONTENDO ALANTOÍNA
In this work, the allantoin was encapsulated with galactomannan extruded from Delonyx regia, by the spray drying technique. The microparticles obtained were structurally characterized by infrared spectroscopy (IR), thermal analysis, scanning electron microscopy (SEM) and the controlled release profile was evaluated. The results of IR suggested the formation
Quím. Nova. Publicado em: 2018-05
-
15. Pulse Eletrodeposition of Ni/nano-Al2O3 Composite Coatings on Cast Iron Cylinder Liner
Ni/nano-Al2O3 composite coating by pulse electrodeposition method has been used for coating on cast iron liner material. The hardness has been increased from 308 HV to 1050 HV through conventional Watts bath and by applying Taguchi's optimization technique with optimum parameters of pulse frequency 120 Hz, duty cycle 40% and peak current density 0.7A/cm2. Th
Mat. Res.. Publicado em: 26/03/2018
-
16. Microstructure and Flight Behaviors of Droplet and its Solidification in Twin-Wire Arc Sprayed Ni-Al Composite Coatings
Droplet flight and solidification behaviors during twin-wire arc sprayed (TWAS) composite coatings were systematically investigated. Both theoretical model and numerical method were established for calculating the droplet deformation, breakup and solidification process in air flow based on the volume of fluid (VOF) dual-phase flow model jointed with the stan
Mat. Res.. Publicado em: 19/03/2018
-
17. The Effect of Electroless Bath Parameters and Heat Treatment on the Properties of Ni-P and Ni-P-Cu Composite Coatings
Ni-P-(Cu) composite coatings were applied on a St37 steel in an acidic bath of hypophosphite composite. The effect of the concentration of the Cu particles and pH of the solutionon the amount of Ni and P of the coatings, their morphology, and hardness of the coatings were explored. Some of the coated samples were also heat treated at 400ºC for 1 hour. The p
Mat. Res.. Publicado em: 08/01/2018
-
18. ITO Obtained by Spray Pyrolysis and Coating on Glass Substrate
Conductive thin films have various applications in different technological fields. Indium tin oxide (ITO) is a mixed oxide. In the film form, ITO has been widely employed as electrode in many optoelectronic devices. Methods like thermal evaporation, sputtering, chemical vapor deposition (CVD), electron beam, spray coating, and sol-gel synthesis give ITO thin
J. Braz. Chem. Soc.. Publicado em: 2017-12
-
19. Electrodeposition of Composite Coatings of Cu/AlO(OH) Using Allyl Alcohol as an Additive
In this work, composite coatings of Cu/AlO(OH) were produced by electrodeposition on steel substrates using a pyrophosphate-based bath containing allyl alcohol as an additive. The electrodeposition of the composite coatings was carried out using a 23 central composite design (CCD), aiming to verify the effects of the deposition parameters (previous stirring
Mat. Res.. Publicado em: 18/09/2017
-
20. Physical-Chemical Properties of the Support Immobead 150 Before and After the Immobilization Process of Lipase
We carried out the physico-chemical characterization of Immobead 150, a hydrophobic support for the immobilization of lipases. Thermomyces lanuginosus lipase (TLL) was immobilized on Immobead 150 by multipoint covalent attachment (ImmTLL) and the morphological, textural, structural, thermal, and physico-chemical properties of the support, before and after en
J. Braz. Chem. Soc.. Publicado em: 2017-08
-
21. Análisis de falla de los bujes del tornillo de una extrusora utilizada para procesar pintura en polvo
ABSTRACT This article aims to present the failure analysis of extruder screw bushings used for the manufacture of powder paint. Two bushings, one from the transition zone and one from the metering zone were selected to carry out the study. Chemical composition and microstructural analysis, hardness testing and a detailed analysis of the failed surfaces by vi
Matéria (Rio J.). Publicado em: 22/06/2017
-
22. ENCAPSULATION OF EXTRACT FROM WINERY INDUSTRY RESIDUE USING THE SUPERCRITICAL ANTI-SOLVENT TECHNIQUE
Abstract Grape pomace (seed, skin and stem) is a winery byproduct with high levels of biologically active compounds, such as antioxidants and antimicrobials, that could be converted into high added-value products. Since these components are easily degraded by oxygen, light and high temperature exposure, stabilization is important, for instance, by a microenc
Braz. J. Chem. Eng.. Publicado em: 2016-09
-
23. Comportamiento Tribológico y Microestructural en Recubrimientos Aplicados por GTAW y HVOF (Proceso Térmico de Espreado) y Usado en Recuperación de Aceros Grado Herramienta AISI/SAE D2
Abstract The Fe-Cr-Mo alloys are use in covers to protect the components that are under wear and corrosion. The high velocity thermo spray covering by HVOF (high velocity oxi-fuel) in Fe-Cr-Mo alloys has reported as a good result in projection fields for the steel tool grade for cold work. The HOVF is an attractive method to apply covering and recuperate dia
Soldag. insp.. Publicado em: 2016-06
-
24. Fabrication and High Temperature Friction Behavior and Oxidation Resistance of Ni-Co-ZrO2 Composite Coating
Ni-Co alloy and ZrO2 micron particles were codeposited on 45 carbon steel by electrodeposition. The composition and microstructure of the composite coating were characterized. The high temperature tribological properties were carried out by a pin-on-disk tribo-tester. Additionally, the oxidation resistance was evaluated via high temperature circulating oxida
Mat. Res.. Publicado em: 05/04/2016