Metallic Substrate
Mostrando 13-24 de 63 artigos, teses e dissertações.
-
13. Evaluation of hydrogen-Induced cracking resistance of the In625 laser coating system on a C-Mn steel substrate
Abstract The corrosion of C-Mn steels in the presence of hydrogen sulfide (H2S) represents a significant challenge to oil production and natural gas treatment facilities. The failure mechanism induced by hydrogen-induced cracking (HIC) in a Inconel 625 coating / C-Mn steel has not been extensively investigated in the past. In the present work, an API 5CT ste
REM, Int. Eng. J.. Publicado em: 2017-06
-
14. Determination of Film Thickness Through Simulation of Vickers Hardness Testing
In recent decades, changes in the surface properties of materials have been used to improve their tribology characteristics. However, this improvement depends on the process, treatment time and, essentially, the thickness of this surface film layer. Physical vapor deposition (PVD) has been used to increase the surface hardness of metallic materials. The aim
Mat. Res.. Publicado em: 13/04/2017
-
15. Electrical and Optical Transport Characterizations of Electron Beam Evaporated V Doped In2O3 Thin Films
Vanadium (5 at. %) doped Indium Oxide (V: In2O3) thin films with different thicknesses (50 nm, 100 nm and 150 nm) were prepared onto glass substrate by electron beam evaporation technique in a vacuum of about 4×10-3 Pa. X-ray diffraction (XRD) pattern revealed that the prepared films of thickness 50 nm are amorphous in nature. Temperature dependence of elec
Mat. Res.. Publicado em: 08/12/2016
-
16. Growth and Electrochemical Stability of Compact Tantalum Oxides Obtained in Different Electrolytes for Biomedical Applications
Tantalum has been cited to have many biomaterial applications, exhibiting biocompatibility and outstanding corrosion resistance. Tantalum may be covered with tantalum oxide using the electrochemical process of anodic oxidation. The oxide surface is known to be bioactive and more corrosion resistant. In this research, compact tantalum oxide films were obtaine
Mat. Res.. Publicado em: 23/10/2015
-
17. A Compact Dual-Band Octagonal Slotted Printed Monopole Antenna for WLAN/ WiMAX and UWB Applications
AbstractA compact (20 x 20 mm2 size), coplanar waveguide (CPW) fed, octagonal slotted, dual-band antenna is presented in this paper. The proposed antenna has a simple structure consisting of an octagonal slot, L-shape stub, and a two stepped rectangular patch. The introduction of the L-shaped metallic stubs in the ground plane generates a lower resonance fre
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2015-06
-
18. Abrasive blasting contamination in Super Duplex and carbon steels - a quantification approach by rietveld analysis
A methodology for quantifying the contamination after abrasive blasting by Aluminum Oxide and Martensitic Carbon Steel particles in Super Duplex and Carbon Steel substrates has been developed. The method consisted of performing x-ray diffraction in the blasted steel substrates and calculating the particle contamination using Rietveld Quantitative Method. In
Mat. Res.. Publicado em: 2014-10
-
19. Heterojunction between Al2O3 and SnO2 thin films for application in transparent FET
Alternative materials for use in electronic devices have grown interest in the past recent years. In this paper, the heterojunction SnO2/Al2O3 is tested concerning its use as a transparent insulating layer for use in FETs. The alumina layer is obtained by thermal annealing of metallic Al layer, deposited by resistive evaporation technique. Combination of und
Mat. Res.. Publicado em: 09/09/2014
-
20. Kinetics Study of Extracellular Detergent Stable Alkaline Protease from Rhizopus oryzae
In this study, extracellular alkaline protease was produced from Rhizopus oryzae in submerged fermentation using dairy waste (whey) as a substrate. Fermentation kinetics was studied and various parameters were optimized. The strain produced maximum protease at initial medium pH of 6.0 medium depth of 26 mm, inoculum size of 2% at incubation temperature of 35
Braz. arch. biol. technol.. Publicado em: 29/08/2014
-
21. Effects of coronal substrates and water storage on the microhardness of a resin cement used for luting ceramic crowns
Composite resin and metallic posts are the materials most employed for reconstruction of teeth presenting partial or total destruction of crowns. Resin-based cements have been widely used for cementation of ceramic crowns. The success of cementation depends on the achievement of adequate cement curing. Objectives: To evaluate the microhardness of Variolink
J. Appl. Oral Sci.. Publicado em: 2014-07
-
22. In Vitro Tensile Strength of Luting Cements on Metallic Substrate
O objetivo deste estudo foi determinar a resistência à tração de coroas cimentadas em substrato metálico com quatro diferentes tipos de agentes cimentantes. Vinte molares humanos maxilares com diâmetros semelhantes foram selecionados e preparados para receberem núcleos metálicos fundidos (Cu-Al). Após cimentação e preparo, os núcleos foram mensur
Braz. Dent. J.. Publicado em: 2014-04
-
23. Preparation of PMMA/hBN composite coatings for metal surface protection
Polyacrylics have been widely used in coatings. However, their application is limited by low corrosion resistance. One way to enhance their properties is the addition of fillers with adequate properties. In this study, composite materials of PMMA and hBN were developed and deposited on steel by dip-coating. The influence of the amount of hBN in the PMMA coat
Mat. Res.. Publicado em: 23/08/2013
-
24. Catalisadores de Pd metálico modificados por líquidos iônicos para a hidrogenação seletiva de compostos poli-insaturados
In this work, heterogeneous catalysts immobilized on supported ionic liquid (IL) were prepared, characterized and investigated in hydrogenation reactions of the substrates 1,5-cyclooctadiene (1,5-COD), trans-cinnamaldehyde (CALD) and nitrobenzene (NB). Two methods were used to prepare the catalysts. In the first, commercial Pd/C catalyst was coated with diff
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 06/08/2012