Machining Forces
Mostrando 1-12 de 31 artigos, teses e dissertações.
-
1. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
2. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
3. Emprego de ferramentas estatísticas para avaliação da usinabilidade de ligas de alumínio
The main objective of the present work is to study the effect of the input variables: mechanical properties of the workpiece (tensile strength, hardness and elongation) and cutting conditions (cutting speed, feed rate, depth of cut and lubri-cooling system) over the output variables: cutting forces, power consumption, cutting temperature, surface roughness (
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/05/2012
-
4. Influência do teor de silício na usinabilidade da liga de alumínio 6351 - avaliada através de força de corte e acabamento superficial / Influence of the silicon content in the machinability of the 6351 aluminium alloy analysed through cutting force and surface finish
The aim of this work is to study the effect of silicon content in the machinability of CBAs (Compania Brasileira de Aluminio) 6351 aluminum alloy measured through cutting force and surface finish. In a first moment the effect of depth of cut (ap), cutting speed (vc), feed rate (f) and silicon content (% Si) on the machinability were investigated. The machini
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/03/2012
-
5. Estudo da influência da força de corte em usinagem a verde nas propriedades mecânicas de cerâmicas sinterizadas / Influence of the cutting force of green machining on the mechanical properties of sintered ceramics
The present study deals with the measurement forces of green machining ceramics and their correlation with the mechanical properties after sintering. The green machining is employed in crude compacts either to check raw formats without compromising the extreme dimensional accuracy or to obtain a preform prior to finish machining after sintering, extensively
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/01/2012
-
6. Machinability study of steels in precision orthogonal cutting
The miniaturization of components and systems is advancing steadily in many areas of engineering. Consequently, micro-machining is becoming an important manufacture technology due to the increasing demand for miniaturized products in recent years. Precision machining aims the production of advanced components with high dimensional accuracy and acceptable sur
Materials Research. Publicado em: 03/07/2012
-
7. An analysis of the machinability of ASTM grades 2 and 3 austempered ductile iron
Austempered Ductile Iron (ADI) is a ferrous material that was first fabricated in the second half of last century, therefore a relatively new material compared to steel, which has been used for different applications by mankind for some millennia now. ADI ;s mechanical properties, such as its strength-to-weight ratio, which has proven to outperform that of f
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 22/08/2011
-
8. Estudo das forças, vibrações e desgaste das ferramentas no fresamento da liga de titânio Ti-6A1-4V / A study about forces, vibration and tool wear in Ti-6A1-4V titanium alloy face milling
Ligas de titânio já apresentam um papel de grande importância na indústria aeroespacial, petroquímica e de biomateriais. A combinação de alta resistência mecânica, baixa densidade, resistência à corrosão, biocompatibilidade, boa tolerância tecidual e manutenção de suas características em altas temperaturas, configuram o titânio como um mater
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 07/02/2011
-
9. Finite element simulations of Ti6Al4V titanium alloy machining to assess material model parameters of the Johnson-Cook constitutive equation
The machining of titanium alloys poses several inherent difficulties owing to their unique mechanical properties and cutting characteristics. Finite element (FE) simulations have reduced the burden of extensive experimental trials in understanding the deformation behavior and optimize the cutting process. The FE code relies on the qualitative nature of input
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-06
-
10. Influence of optimized lubrication-cooling and minimum quantity lubrication on the cutting forces, on the geometric quality of the surfaces and on the micro-structural integrity of hardened steel parts
The is paper presents an analysis of the influence of minimum quantity lubrication (MQL), optimized and conventional cooling, using different cutting fluid volumes and flow rates, on the surface quality and integrity of hardened steel workpieces, in cylindrical plunge grinding with superabrasive CBN grinding wheels. The final quality of the workpieces were e
Matéria (Rio de Janeiro). Publicado em: 2011
-
11. Estudo dos esforços de corte no processo HSM aplicado à abertura de cavidades / Study of the cutting forces in HSM process applied to pocket milling
The manufacturing of a great number of components in the industry depends on molds and dies used in processes like forging, powder metallurgy, deep drawing, casting and plastic injection. One of the main operations for manufacturing of these parts corresponds to the opening of the initial pocket, from which more complex geometries are machined in order to ob
Publicado em: 2010
-
12. Influência do ciclo de füração na usinabilidade do ferro fundido cinzento GH190 / Influence of Cycle Drilling Machinability in Gray Cast Iron GH190
Dentre as operações de usinagem, a furação com brocas helicoidais destaca-se por ser uma das mais utilizadas na indústria metal-mecânica. Apesar de a literatura apresentar muitas pesquisas, percebe-se que ainda existe espaço para trabalhos científicos sobre o processo de furação. O presente trabalho analisa a influência do ciclo de furação (cont
Publicado em: 2010