Graphite Electrodes
Mostrando 25-36 de 57 artigos, teses e dissertações.
-
25. Employment of cathodes of diffusion of oxygen in eletrotrolise of brine to produce chlorine / Emprego de catodos de difusão de oxigenio na eletrolise da salmoura para a produção de cloro
This work is investigating the performance of electrodes modified with gaseous diffusion of particles of Cu, for reduction of oxygen in the production of chlorine during the electrolysis of brine. Initially, the reaction was studied on the anodic oxidation of chloride ion. Using a single cell compartment, with the type DSA anode with an area of 1.5 cm2 as wo
Publicado em: 2009
-
26. Funcionalization of mesoporous silica with 2-bezothiazolethiol and 3-mercaptopropyltrimetoxysilane for electronalytical application / Funcionalização de sílicas mesoporosas com benzotiazol-2-tiol e 3-mercaptopropiltrimetoxisilano para aplicações em eletroanalítica
Mesoporous silicas were functionalised by immobilisation of organic substances covalently bonded to the silanol groups on the silica surface. SBA-15 nanostructured silica was functionalised by post-synthesis with 2-benzothiazolethiol and silica films modified with 3-mercaptopropyltrimethoxysilane were obtained by direct functionalisation. The characterizatio
Publicado em: 2009
-
27. Reciclagem de pilhas: recuperação do manganês na forma do dióxido de manganês eletrolítico. / Recycling of batteries: recovery of manganese in the form of electrolytic manganese dioxide.
Considering the growing demand for products containing manganese in its composition, this work seeks to verify the possibility of using depleted batteries as a source of manganese applying the electrolytic process. It was used an electrolyte solution containing the metal ions: Ca (270mg / L), Ni (3000 mg / L), Co (630 mg / L), Mn (115300 mg / L), Ti (400 mg
Publicado em: 2009
-
28. Aqueous Congo Red degradation induced by plasma with glow discharge electrolysis / Degradação do corante Vermelho Congo em solução aquosa através de plasma obtido por eletrólise de alta tensão
Due to the concern with environmental impact and the need for the use of dyes for the textile industries, during the last years several studies has been undertaken to develop new technologies for energetic treatments that allow the degradation of compounds present in industrial waste. In this present work, the construction of a system for degradation of orga
Publicado em: 2009
-
29. Preparación electroquímica de electrodos bimetálicos PtRu soportados sobre sustratos carbonosos y su caracterización para la oxidación de metanol en medio ácido
In this work the influence of the electrochemical oxidation of different carbon substrates, such as glassy carbon, graphite cloth, graphite felt, and carbon fiber paper, on the electrodeposition of bimetallic PtRu catalysts was studied. The oxidation of the different substrates prior to the catalyst deposition, leads to remarkable improvement of catalyst dis
Matéria (Rio de Janeiro). Publicado em: 2008-06
-
30. Desenvolvimento e aplicação de eletrodos compósitos à base de grafite e Araldite® / Development and apllication of composite electrode graphite-Araldite®
The development and evaluation of the voltammetric behavior of composite electrodes prepared with graphite as a conducting phase and commercial epoxy resin Araldite ® as an insulating phase was performed. The resin was prepared according to instructions of the manufacturer and mixed with a suitable amount of graphite in order to prepare composites with 50,
Publicado em: 2008
-
31. Material carbono ceramico condutor SiO2/ZrO2/C-grafite : sintese, caracterização e aplicações / SiO2/ZrO2/C-graphite conducting carbon ceramic material : synthesi characterization and application
SiO2/ZrO2/C-graphite was prepared by the sol-gel method in two compositions: (A) SZC30 (SiO2 = 50 %, ZrO2 = 20 %, C = 30 %) e (B) SZC20 (SiO2 = 60 %, ZrO2 = 20 %, C = 20 %) in % m/m, characterized and used to prepare electrodes. The carbon ceramic material was thermally treated at 400, 600, 800 and 1000 °C in nitrogen atmosphere, and it was observed that it
Publicado em: 2008
-
32. The use of vegetal-based dielectric fluids in die-sink EDM processes / Utilização de fluidos dielétricos à base de óleos vegetais na usinagem por descargas elétricas por penetração
Dielectric fluids usually used in electrical discharge machining (EDM) are generally expensive, toxic and demand special storage and disposal procedures. Oil-based dielectric fluids pollute the environment and are subject to the price variations of the international market. Moreover, they are used in large quantities and discarded after short periods of time
Publicado em: 2008
-
33. Desenvolvimento e aplicação de eletrodos à base de nanotubos de carbono / DEVELOPMENT AND APPLICATION OF ELECTRODE BASE ON CARBON NANOTUBES
The electrodes based on carbon nanotubes (CNTs) were prepared in the form of paste of CNTs/Graphite and film on glassy carbon electrode. These electrodes were electrochemically characterized by their response in potassium ferricyanide and hydroquinone. Considering the obtained results, the electrode in the form of paste was selected for analytical applicatio
Publicado em: 2008
-
34. Polyphosphate Gels Applied to Electrochemical Devices Assembling / AplicaÃÃo de gÃis de polifosfatos à construÃÃo de dispositivos eletroquÃmicos
Hybrid materials between aluminum and iron polyphosphate gels, polyaniline and carbon materials were synthesized and were used as electrode materials to assemble electrochemical devices. The aluminum and iron polyphosphate gels, the carbon materials as well as the hybrids obtained between these materials and polyaniline were characterized by thermogravimetri
Publicado em: 2008
-
35. The behavior of graphite and copper electrodes on the finish die-sinking electrical discharge machining (EDM) of AISI P20 tool steel
The machining parameter settings installed at CNC EDM machines are developed under optimum process conditions. Standard workpiece and electrode materials are used traditionally by machine manufacturers to establish the EDM parameter settings. However, this is not the usual situation of the tooling industry, where many different grades of workpiece and tool e
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2007-12
-
36. Development of graphite-polymer composites as electrode materials
Graphite powder was mixed to polyurethane, silicon rubber and Araldite® (epoxy) in order to prepare composite materials to be used in the preparation of electrodes. Results showed that voltammetric response could be obtained when at least 50% of graphite (w.w-1) is present in the material. SEM and thermogravimetry were also used in the characterization of t
Materials Research. Publicado em: 2007-06