Fracture Toughness
Mostrando 1-12 de 170 artigos, teses e dissertações.
-
1. Influence of the addition of niobium oxide on the properties of fused aluminum oxide used in abrasive tools
Abstract Fused alumina is a material used in the manufacturing of abrasive tools, due to its high fusion point, great hardness, and mechanical toughness. In this context, this study addressed the influence of niobium addition on the properties of fused alumina for abrasive applications. A comparison was also made between this oxide and the brown fused alumin
Cerâmica. Publicado em: 2022
-
2. Influence of sintering parameters on the microstructure and mechanical properties of nanosized 3Y-TZP ceramics
Abstract The fracture toughness of 3Y-TZP ceramics obtained from a nanocrystalline powder with an optimized microstructure and highly transformable tetragonal grains was investigated. Samples of ZrO2-3 mol% Y2O3 were sintered at temperatures between 1250 and 1400 °C, with isothermal holding times of up to 16 h. Samples sintered at 1250 °C exhibited relativ
Cerâmica. Publicado em: 2021-03
-
3. Effect of LZSA glass-ceramic addition on the erosive wear of pressureless sintered alumina
Abstract This study aims to evaluate the influence of the 11.6Li2O-16.8ZrO2-68.2SiO2-3.4Al2O3 (mol%) glass-ceramic addition (LZSA, 7 to 21 vol%) on the erosive wear of alumina in comparison to values of pure alumina obtained from the literature. Thus, composites were prepared from three commercial alumina of different initial particle sizes. Specimens were o
REM, Int. Eng. J.. Publicado em: 2020-06
-
4. Post-elastic Deformation Characteristics of Hybrid Fibre Reinforced Concrete Composites
Abstract The present study was focused on evaluating the strength and failure properties of hybrid micro-fibre concretes containing micro brass and steel fibre additions. Experimental tests were conducted on different hybrid fibre concretes containing aligned fibres in the direction of beam axis and the relative mechanical performance was compared to randoml
Lat. Am. j. solids struct.. Publicado em: 10/01/2020
-
5. PM versus IM Ti-5Al-5V-5Mo-3Cr Alloy in Mechanical Properties and Fracture Behaviour
The comparisons of mechanical properties and fracture behaviour between as-consolidated PM Ti-5553 alloy and as-cast IM Ti-5553 alloy were investigated through tensile, fracture toughness and impact toughness tests in this research. The slightly higher strength but much higher ductility and toughness can be identified in IM alloy specimens, which is also con
Mat. Res.. Publicado em: 27/06/2019
-
6. Desempenho balístico de estruturas multicamadas à base de alumina/epóxi
Resumo Alumina é comumente utilizada em blindagens compostas. Apresenta baixa tenacidade à fratura e esta propriedade está relacionada à resistência a múltiplos disparos. Com o intuito de melhorar a durabilidade em campo uma alternativa seria utilizar cerâmicas multicamadas. Neste estudo foi avaliado o desempenho balístico de estruturas multicamadas
Cerâmica. Publicado em: 06/06/2019
-
7. Experimental studies of short concrete reinforced steel fiber beams under bending
Resumo Este estudo apresenta os resultados do rompimento de dois grupos de vigas de concreto com fibras de aço. Cada grupo foi composto de 4 vigas com vão de 300 mm, 4 com vão de 500 mm e 4 com vão de 800 mm e seção de 15 cm x 15 cm. A variação dos grupos se deu pela quantidade de fibras (I com 40 kg/m³ e II com 60 kg/m³). Foram avaliados o comport
Rev. IBRACON Estrut. Mater.. Publicado em: 20/05/2019
-
8. Oxidation Behavior of Al-Y Coating on γ-TiAl at 900°C
ABSTRACT In this study, an Al-Y coating was applied to enhance the property of oxidation resistance on the surface of γ-TiAl alloys by rf magnetron sputtering. The isothermal oxidation tests were investigated at 900 °C for 100 h. The coating characteristics and microstructure of coating after isothermal oxidation were inspected by XRD and SEM methods respe
Matéria (Rio J.). Publicado em: 20/05/2019
-
9. Brittleness index and its relationship with materials mechanical properties: Influence on the machinability of CAD/CAM materials
Abstract: The aim of this study is to evaluate the machinability of four CAD/CAM materials (n = 13) assessed by brittleness index, Vickers hardness, and fracture toughness and interaction among such mechanical properties. The materials selected in this in vitro study are Feldspathic ceramic [FC], Lithium-disilicate glass ceramic [LD], leucite-reinforced glas
Braz. oral res.. Publicado em: 04/04/2019
-
10. Effect of RAP content on flexural behavior and fracture toughness of flexible pavement
Abstract The use of recycled Reclaimed Asphalt Pavement (RAP) material into flexible pavement contributes to sustainable development with environmental and economic benefits. In the present work, Semi-Circular Bending (SCB) specimen has been adopted to study the flexural strength and mode-I fracture toughness of flexible pavement with and without RAP. Two di
Lat. Am. j. solids struct.. Publicado em: 21/03/2019
-
11. Densification and microstructure of Si3N4-TiN ceramic composites
Abstract Silicon nitride is a ceramic material widely used in various structural applications at high temperatures owing to its excellent combination of mechanical and thermal properties. To increase the application of Si3N4, many researches have been developed to improve its fracture toughness and processing conditions. In this study, the sintering and micr
Cerâmica. Publicado em: 2019-01
-
12. Effect of Hot Deformation on Microstructure, Hardness and Precipitation Kinetics in a C350 Maraging Steel Modified by Titanium Addition
Maraging steels are alloys with a good balance between strength and fracture toughness. These properties are obtained by quenching and aging treatments, where the precipitation of intermetallic compounds is promoted in a martensitic matrix. In this context, this paper aims to evaluate the effect of hot deformation on microstructure, kinetics and formation of
Mat. Res.. Publicado em: 17/09/2018