Fe Cr Ni Alloys
Mostrando 1-12 de 22 artigos, teses e dissertações.
-
1. Efecto de los parámetros de aplicación en recubrimientos de Ni-Cr-B-Fe-Si obtenidos por Flame Spray
ABSTRACT Surface damage of components in service is an issue of great industrial interest because of the costs associated to the replacement of certain critical components. There are several techniques to generate coatings, which provide increased resistance to a particular type of surface damage. In this way, it is achieved surface protection to different s
Matéria (Rio J.). Publicado em: 02/08/2018
-
2. Kinetics Oxidation and Characterization of Cyclically Oxidized Layers at High Temperatures for FeMnSiCrNiCe and FeSiCrNi Alloys
Conventional stainless steels are used in cyclic oxidation, but the high amount of Cr and mainly Ni increase the price of these alloys. The objective of the present study was to assess the cyclic oxidation resistance of FeSiCrNi and FeMnSiCrNiCe alloys in comparison to AISI 304 and AISI 310 stainless steels by evaluating the oxidation kinetics and using char
Mat. Res.. Publicado em: 18/09/2017
-
3. Embrittlement and Corrosion Decay of a Cast Duplex Stainless Steel
Duplex stainless steels (DSS) are Fe-Cr-Ni-Mo alloys, with low carbon content, which have a favorable combination of mechanical properties and corrosion resistance. These characteristics are mainly attributed to a dual phase and refined microstructure, typical of these alloys, consisting of similar amounts of ferrite and austenite. For this reason, DSS are w
Mat. Res.. Publicado em: 20/07/2017
-
4. Series of Nanocrystalline NiCoAlFe(Cr, Cu, Mo, Ti) High-Entropy Alloys produced by Mechanical Alloying
Abstract The mechanical alloying technique was employed to produce series of high entropy alloys, combining in equiatomic percentage Al, Co, Cr, Cu, Fe, Mo, Ni and Ti. Milling times were 0, 10, 20 and 30 h, and experiments were performed in a high energy ball mill (SPEX-8000M) under argon atmosphere. The structural and microstructural changes due to mechanic
Mat. Res.. Publicado em: 08/08/2016
-
5. Development of nano-oxide dispersed 304L steels by mechanical milling and conventional sintering
In the present work an attempt has been made to synthesize 304L stainless steels alloy powders with nominal compositions 70.00Fe-19.00Cr-11.00Ni (alloy A), 69.00Fe-19.00Cr-11.00Ni- 1.0 Y2O3(alloy B), and 69.00Fe-19.00Cr-11.00Ni- 1.0 TiO2(alloy C), (all in wt.%) by mechanical milling and conventional sintering at 1150°C for 1.0 hour in argon atmosphere. Exte
Mat. Res.. Publicado em: 19/02/2016
-
6. Optimization of the Deposition Parameters of HVOF FeMnCrSi+Ni+B Thermally Sprayed Coatings
AbstractHVOF thermal spray process produces coatings with low porosity and low oxide content, as well as high substrate adhesion. Small variations on the parameters of the HVOF process can generate coatings with different characteristics and properties, which also is chemical composition depended of the alloy. FeMnCrSi alloy is a cavitation resistant class o
Soldag. insp.. Publicado em: 2015-06
-
7. Produção de recobrimentos metálicos a partir de ligas de ferro amorfizáveis / Production of metallic coatings based on amorphous iron alloys
The aim of this work was to study the production of metal coatings from amorphous alloy Fe-25Cr-7Ni-4,5B (wt.%), with special focus on mechanical and microstructure properties. Initially, preliminary studies were made through the production of ribbons and bulks of metallic alloys Fe-25Cr-7Ni-XB (X = 3.5, 4.5, 5.5 wt.%) for the evaluation of amorphous phase f
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 23/10/2011
-
8. Propriedades físicas do SnO2: defeitos, impurezas, ligas e superredes. / Physical properties of SnO2: defects, impurities, alloys and superlattices.
O dioxido de estanho na estrutura rutila (SnO2) é um semicondutor de gap largo e faz parte da classe dos óxidos condutores transparentes (TCO). Possui gap direto de 3,6 eV e condutividade do tipo n, mesmo quando não dopado intencionalmente. Estudos teóricos e experimentais atribuem este comportamento à presença de defeitos intrínsecos. Por outro lado,
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 19/08/2011
-
9. Mecanismo de fratura por queda de ductilidade em ligas Ni-Cr-Fe / Ductility-dip cracking mechanism in Ni-Cr-Fe alloys
A fratura por queda de ductilidade (FQD) é um tipo de falha que ocorre em temperatura elevada e que afeta adversamente diversos materiais metálicos com estrutura cristalina cúbica de faces centradas (CFC), tais como, ligas de Níquel, Cobre e aços inoxidáveis. Na FQD é observada uma forte redução da ductilidade e a ocorrência de fratura intergranula
Publicado em: 2010
-
10. Influencia do teor de niquel e da temperatura nas propriedades mecanicas e na microestrutura das ligas Fe-18Cr-Ni / Influence of nickel content and temperature in the mechanical properties and microstructure of Fe-18Cr-Ni alloys
Os efeitos da adição de níquel e da temperatura em ligas ferro-cromo foram estudados. Sete ligas de base ferro, com 18% Cr e teores de níquel variando entre zero e 60%, foram utilizadas no estudo (0, 10, 20, 30, 40, 50 e 60% Ni). Foram realizados ensaios de tração em temperatura ambiente, 350 e 700 ºC; simulação por termodinâmica computacional; mic
Publicado em: 2008
-
11. Desenvolvimento de teste in-situ de deformação a alta temperatura no MEV e sua aplicação no estudo do fenomeno de fratura por queda de ductilidade em ligas de niquel / Development of SEM in-situ high temperature-deformation test and its application to the study to the study of ductility dip cracking phenomemon on Ni-base alloys
Foi desenvolvido um experimento para estudo in-situ dos processos de deformação a alta temperatura no interior do microscópio eletrônico de varredura, permitindo assim o estudo do fenômeno de trincamento a alta temperatura, denominado fratura por queda de ductilidade. Este experimento teve como finalidade o estudo específico das ligas de níquel AWS A5
Publicado em: 2008
-
12. Study of alloys and magnets prepared by the hydrogenation, disproportionation, desorption and recombination process (HDDR) based on the Pr-Fe-B system with dopants and alloying additions / Estudo de ligas e ímãs preparados pelo processo hidrogenação, desproporção, dessorção e recombinação (HDDR) à base de Pr-Fe-B com adição de dopantes elementos de liga
A adição de elementos dopantes e elementos de liga aos magnetos permanentes policristalinos à base de terras raras tem como objetivo a melhora das propriedades magnéticas. Neste trabalho estudou-se a adição de 0,1% at. dos elementos: Ti, V, Cr, Ni, Zr, Nb ou Mo na composição Pr14FebalCo16B6 ; as adições de 0,1 % at., 0,3 % at. e 0,5 % at. dos eleme
Publicado em: 2008