Dental Stress Analysis
Mostrando 13-24 de 63 artigos, teses e dissertações.
-
13. DISTRIBUIÇÃO DE TENSÕES EM MOLAR RESTAURADO PELA TÉCNICA ENDOCROWN / Stress distribution in molar restored Endocrown technique
Dentes tratados endodonticamente apresentam geralmente reduzida estrutura coronária e grande risco de falha biomecânica, quando comparados com dentes vitalizados, sendo, portanto, sua técnica restauradora um desafio para a Odontologia. O objetivo do presente estudo foi analisar, usando o método de elementos finitos (MEF), a distribuição de tensões em
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/02/2012
-
14. Influência da abfração, morfologia radicular e carregamento no comportamento biomecânico de pré-molares superiores
O objetivo deste estudo foi investigar o comportamento biomecânico de prémolares superiores relacionando morfologia radicular e profundidade de lesão cervical não cariosa abfração, variando o tipo de carregamento, carga axial e oblíqua, por meio da análise tridimensional de elementos finitos (3D FEA) e teste de extensometria em pré-molares humanos.
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/02/2012
-
15. Stress distribution and screw detorque analysis : influence of misfit and alloy types in cast implant retained frameworks / Avaliação das tensões e do destorque de parafusos : influência do desajuste marginal e dos tipos de metais em infraestruturas protéticas retidas por implantes
O objetivo neste estudo foi avaliar a distribuição das tensões geradas aos implantes modificados, por meio de análise extensométrica e força de destorque dos parafusos de retenção protética, de acordo com o tipo de metal da infraestrutura (Titânio comercialmente puro - Ti c.p ou Cobalto-Cromo - Co-Cr) e presença ou ausência de desajuste vertical
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 10/02/2012
-
16. Morse taper implants at different bone levels: a finite element analysis of stress distribution
AIM: To explore the biomechanical effects of the different implantation bone levels of Morse taper implants, employing a finite element analysis (FEA). METHODS: Dental implants (TitamaxCM) with 4x13 mm and 4x11 mm, and their respective abutments with 3.5 mm height, simulating a screwed premolar metal-ceramic crown, had their design performed using the softwa
Braz. J. Oral Sci.. Publicado em: 2012-12
-
17. Análise fotoelástica da distribuição das tensões ocorridas no tecido ósseo, ao redor de cinco diferentes desenhos de implante, quando submetidos ao carregamento axial / Photoelastic analysis of stress distributions occurring around the bone tissue of five different designs of implants when subjected to axial loading
The design of the implant is a highly relevant factor in the distribution of stresses generated in the peri-implant tissues. The proposition of this study was to evaluate the stress distribution of five different designs of implants, when subjected to axial loads uniformly distributed. Were prepared five photoelastic jaws, in which the implants used in this
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 26/09/2011
-
18. Avaliação in vitro da transmissão de carga oclusal em próteses sobre implantes em função da inclinação de implantes através de análise fotoelástica / In vitro evaluation of occlusal load transmission in prosthetic implant according to the inclination of implants by photoelastic analysis
The All-on-Four technique was conceived in order to decrease the length of the cantilever in the rehabilitation of edentulous patients with implant-supported prosthesis. However, still persist questions related to the biomechanical behavior of implants and the proper technique All-on-Four, since issues such as peri-implant bone loss and failure of the prosth
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/09/2011
-
19. Análise fotoelástica da tensão de contração da polimerização de compósitos resinosos sob influência de técnicas restauradoras / Photoelastic analysis of polymerization shrinkage stress of composites under the influence of restorative techniques
Polymerization shrinkage stress is an undesirable and inevitable characteristic of adhesive restorations. It is important to understand the stress distribution to improve the clinical effectiveness of resin composite restoration. Chapter 1: The aim was to evaluate the polymerization shrinkage stress and degree of conversion of a resin composite material subm
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 20/06/2011
-
20. Análise tridimensional por elemento finito do comportamento biomecânico de próteses totais fixas implantossuportadas : efeito do tipo de conexão protética, cargas oclusais e número de implantes / Three-dimensional finite element analysis of biomechanics of implant-supported fixed prostheses : effect of connection system, occlusal load, and number of implants
The purpose of this study was to analyze the stress and strain distribution by three-dimensional finite element method in implant supported fixed prostheses and peri-implantar bone region, using two types of implant-abutment connection internal and external, correlated to the effect of axial loadings and number of implants. Virtual models were developed by s
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/04/2011
-
21. Avaliação biomecânica de pré-molares superiores restaurados com diferentes monômeros resinosos / Biomechanical evaluation of pre-molars restored with different monomers resins
O objetivo deste trabalho foi avaliar a viabilidade da utilização de um método de geração de modelo tridimensional de pré-molar superior, com capacidade de representar as tensões de contração de polimerização por meio de analogia térmica com aplicabilidade ao método de elementos finitos. Após isto, neste trabalho avaliou-se o comportamento biom
Publicado em: 2011
-
22. Polymerization Shrinkage and Flexural Modulus of Flowable Dental Composites
Linear polymerization shrinkage (LPS), flexural strength (FS) and modulus of elasticity (ME) of low-viscosity resin composites (Admira Flow™, Grandio Flow™/VOCO; Filtek Z350 Flow™/3M ESPE; Tetric Flow™/Ivoclar-Vivadent) was evaluated using a well-established conventional micro-hybrid composite as a standard (Filtek Z250™/3M ESPE). For the measureme
Materials Research. Publicado em: 2010-09
-
23. Análise fotoelástica de distribuição de tensões em implantes paralelos e em protocolo tipo all-on-four / Photoelastic analysis of stress distribution in parallel implants and protocol all-on-four
O objetivo nesta pesquisa foi avaliar in vitro através da fotoelasticidade, as tensões induzidas em protocolos com implantes inclinados (conceito All-on-Four) e paralelos, utilizados em prótese sobre implantes mandibulares com infraestruturas confeccionadas em titânio, soldadas a laser e submetidos à carga distal. Os protocolos foram confeccionados com
Publicado em: 2010
-
24. Avaliação da distribuição de tensões em diferentes topografias residuais de molares restaurados com Endocrown / Analysis of the stress distribution in different residual topographic of a molar tooth restored with endocrowns
O objetivo deste trabalho foi analisar pelo método de elementos finitos (MEF) a distribuição de tensões em diferentes preparos cavitários que utilizaram a câmara pulpar disponível de um dente molar desvitalizado para a estabilidade e retenção de restauração Endocrown, submetida à simulação de forças oclusais funcionais. A tomografia computador
Publicado em: 2010