Cracking
Mostrando 1-12 de 298 artigos, teses e dissertações.
-
1. Influence of bottom ash and red mud additions on self-leveling underlayment properties
Abstract Self-levelling underlayments (SLUs) based on Portland cement (PC) are susceptible to cracking due to drying shrinkage. The present study evaluated the influence of binder contents on systems consisting of calcium aluminate cement (CAC), PC, and a source of calcium sulfate (C$), derived from the flue gas desulfurization process (FGD), on the mechanic
Cerâmica. Publicado em: 2022
-
2. Ternary system Portland cement-calcium aluminate cement-calcium sulfate applied to self-leveling mortar: a literature review
Abstract The modernization of building systems is increasingly demanding products that improve efficiency during their processing. The development of self-leveling mortars for the regularization of flooring is a consequence of this evolution. The high contents of binder and water to obtain self-flowing property, plus the application of thin layers over large
Cerâmica. Publicado em: 2021-03
-
3. Flexible pavement overlay design of UFJF ring road based on the new Brazilian mechanistic-empirical pavement design method
Abstract The procedures for design and reinforcement projects regarding flexible pavements available in Brazil are mostly based on empirical models developed from studies carried out in specific localities, and therefore, should only be used in cases where equivalent climatic and traffic conditions are observed. The national highway agencies in partnership w
REM, Int. Eng. J.. Publicado em: 2020-12
-
4. Analysis of cracks and coating in iron ore pellets by digital image processing
Abstract The pelletizing process agglomerates ore fines previously considered as tailings and makes its application possible in the form of pellets. During the process, the pellets are subjected to various compressive forces and temperature changes, which cause ruptures in their surface. These ruptures (cracks) impair the performance of the pellets in the re
REM, Int. Eng. J.. Publicado em: 2020-09
-
5. PREPARATION AND SIMULATION OF THE ON-LINE SiO2/S COATING FOR COKING INHIBITION IN THE INDUSTRIAL CRACKING FURNACE
Abstract Coke formation inside radiant coils is one of the main problems during thermal cracking of hydrocarbons. The on-line preparation of the coating for coking inhibition is a promising technology because it provides more flexibility to the operators on site. The SiO2/S coating was prepared on the inner surface of coils in an 8-year-served GK-VI industri
Braz. J. Chem. Eng.. Publicado em: 13/01/2020
-
6. Lateral loss of clay in the genesis of Luvisols in the Semi-Arid Depression of the Jequitinhonha Valley, Minas Gerais - Brazil
RESUMO Os solos da região semi-árida de Minas Gerais possuem pequena profundidade; consistência dura, muito dura ou mesmo extremamente dura quando seca e muito plástica e muito pegajosa quando úmida; estrutura colunar ou em blocos angulares e fendilhamento significativo ao longo do perfil no período seco, entretanto eles não foram profundamente estuda
Ciênc. agrotec.. Publicado em: 05/12/2019
-
7. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
8. Experimental study of reinforced masonry beams
Resumo Com objetivo de contribuir com o melhor entendimento do comportamento de vigas de alvenaria estrutural armada, foi realizado o estudo experimental de vigas de alvenaria armada com blocos de concreto. Essas foram projetadas para ruptura à flexão, sendo analisando o modo de fissuração, a flecha, o momento fletor último, a deformação por encurtame
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
9. Structural models for analysis of reinforced concrete frame buildings with masonry infills
Resumo Este trabalho tem como objetivo o estudo do comportamento de pórticos de edifícios de concreto armado preenchidos com alvenaria frente às ações horizontais, empregando-se dois modelos estruturais: i) modelo de diagonal equivalente (MDE) e ii) modelo com elementos finitos bidimensionais para estado plano de tensões (MEF). No primeiro modelo, a al
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
10. Phase Separation and Development of the Microstructure for Stainless Steel to Copper Alloy Weld Joints Using a Fiber Laser
ABSTRACT Stainless steel and copper alloys joints are often applied in aerospace, marine and power industries where both high thermal and electrical conductivity (Cu) and corrosion resistance (steel) are required. In the aerospace industry, in particular for the combustion chamber of rocket engines, copper and steel combinations offer perfect materials selec
J. Aerosp. Technol. Manag.. Publicado em: 10/10/2019
-
11. Análise da influência do tipo de agregado miúdo nas características e dosagem de argamassas mistas
Resumo As argamassas de revestimento e assentamento de alvenaria com uso de areia artificial de britagem tem se tornado uma alternativa viável nos últimos anos, contudo têm-se grandes divergências quanto a preceitos de dosagem adequada para esses materiais. Diante disso, este trabalho objetiva estudar argamassas mistas de revestimento e assentamento de a
Ambient. constr.. Publicado em: 03/10/2019
-
12. Optimized design of RC deep beams based on performance metrics applied to strut and tie model and in-plane stress conditions
Abstract Deep beams do not behave according to classical beam theory. The nonlinearity of strain distribution within these elements requires application of strut and tie models (STM) or other alternatives to evaluate the complex stress field. Although the design of these elements is a common task for structural engineers, limited research is found on assessi
Lat. Am. j. solids struct.. Publicado em: 22/08/2019