Arc Based
Mostrando 13-24 de 145 artigos, teses e dissertações.
-
13. Contrastive Research on Electrical Contact Performance for Contact Materials of Cu-SnO2 and Cu-ZnO2 Alloys
Herein, SnO2- and ZnO2-doped (1.5 wt.%) composite Cu powder was prepared by mechanical alloying (MA) respectively, and both the contact materials of oxide-doped Cu alloys were subsequently obtained by canned hot-pressing powder sintering with hot extrusion combined. Scanning electron microscopy (SEM), laser scanning confocal microscopy (LSCM) and self-design
Mat. Res.. Publicado em: 25/04/2019
-
14. Rely XTM U200 versus Rely XTM ARC: uma comparação da resistência à microtração
Resumo Introdução Os cimentos resinosos são extensivamente utilizados na fixação de restaurações indiretas de cerâmica e cerômero, sendo classificados em duas categorias: os cimentos resinosos convencionais, que não apresentam uma adesão inerente à estrutura dental e requerem o uso de um sistema adesivo e os cimentos resinosos autoadesivos, que
Rev. odontol. UNESP. Publicado em: 11/03/2019
-
15. Cadernos como artefatos etno-históricos
Resumo: A pesquisa está embasada em perspectivas metodológicas etnográficas, das quais deriva a caracterização dos cadernos como componentes de uma etno-história de individualidades e coletivos. São analisados elementos gráficos, produzidos num arco cronológico que abrange da década de 1920 até a contemporaneidade. O corpus documental é constitu�
Rev. Bras. Hist. Educ.. Publicado em: 14/01/2019
-
16. Effect of Residual Stresses of GTA Welding for Dissimilar Materials
The purpose of the present work is to understand the evolution of residual stresses in weldments. The study made to weld the multipass dissimilar of Nickel-based superalloy Inconel 625 and stainless steel 316L using Continuous Current Gas Tungsten Arc Welding (CCGTAW) and Pulsed Current Gas Tungsten Arc Welding (PCGTAW) process employing ERNiCrMo-3 and ERNiC
Mat. Res.. Publicado em: 25/06/2018
-
17. The influence of Nano-TiO2 and Nano-Al2O3 Particles in Silicate Based Electrolytes on Microstructure and Mechanical Properties of Micro Arc Coated Ti6Al4V Alloy
Ceramic oxide coatings were fabricated on Ti6Al4V alloy by micro arc oxidation (MAO) in silicate electrolytes, with nano-TiO2 and nano-Al2O3 and without nano-additives. Effects of nano additives on the structural and mechanical properties of the MAO coatings were analysed. The MAO coatings were investigated by scanning electron microscopy (SEM), Energy-Dispe
Mat. Res.. Publicado em: 18/06/2018
-
18. Theoretical Approach to Simulate Efficient Selective Solar Absorbers With Micro or Nano Structured Arrays
Study of the solar absorber with photonic crystal or micro structures as the heat absorbing surfaces operated at a high-temperature was conducted. Numerical calculations based on rigorous coupled-wave analysis were performed to determine the absorptance of the photonic crystal surface on the absorber. The effect of nano geometry of the photonic crystal in tu
Mat. Res.. Publicado em: 22/03/2018
-
19. Microstructure and Flight Behaviors of Droplet and its Solidification in Twin-Wire Arc Sprayed Ni-Al Composite Coatings
Droplet flight and solidification behaviors during twin-wire arc sprayed (TWAS) composite coatings were systematically investigated. Both theoretical model and numerical method were established for calculating the droplet deformation, breakup and solidification process in air flow based on the volume of fluid (VOF) dual-phase flow model jointed with the stan
Mat. Res.. Publicado em: 19/03/2018
-
20. Influence of Nanoxides on Diffusivity and Solubility of Hydrogen in Pd-based alloys
The hydrogen interaction in palladium alloys with addition of Ce, Zr and Y was studied. These alloys are produced by arc-melting and then cold rolled into thin foils. Heat treatment at 800ºC for 24h in air atmosphere is applied to induce internal oxidation. Hydrogen permeation tests and TDS (Thermal Desorption Spectroscopy) are carried out to evaluate hydro
Mat. Res.. Publicado em: 11/01/2018
-
21. COLUMN GENERATION BASED ALGORITHMS FOR THE CAPACITATED MULTI-LAYER NETWORK DESIGN WITH UNSPLITTABLE DEMANDS
ABSTRACT We investigate a variant of the Multi-Layer Network Design problem where minimum cost capacities have to be installed upon a virtual layer in such a way that (i) a set of traffic demands can be routed AND (ii) each capacity (subband) is assigned a route in the physical layer. The traffic demands cannot be splitted along several paths (nor even sever
Pesqui. Oper.. Publicado em: 2017-09
-
22. Distributional patterns of Aptian-Albian paleoichthyofauna of Brazil and Africa based on Track Analysis
ABSTRACT The Aptian-Albian paleoichthyofauna in Brazil and Africa is quite diverse, yet their geographic patterns still require accounts. This work consists of a panbiogeographical analysis of paleoichthyofauna from Aptian-Albian through track analysis. Geographic coordinates were obtained and converted into paleocoordinates. Individual Tracks (ITs) and Gene
An. Acad. Bras. Ciênc.. Publicado em: 02/03/2017
-
23. Impact Analysis of PM magnetization level on motor performance: simulations and experimental results
Abstract This paper addresses the impact of magnetization level tolerances in ferrite-based permanent magnets (PM) on the performance of brushless DC motors. A case study is prepared using three motor prototypes assembled with controlled samples of ferrite arc segments, in terms of magnetization. The investigation is performed both experimentally and through
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2017-03
-
24. A gis-based tool for estimating soil loss in agricultural river basins
Abstract Soil erosion is a major problem observed in terrestrial ecosystems. Monitoring and identifying potential areas for erosion becomes extremely important for the better management of these areas. The main aim of this study was to develop a Geographic Information System script tool based on the universal soil loss equation (USLE), which calculates soil
REM, Int. Eng. J.. Publicado em: 2016-12