Aluminium
Mostrando 37-48 de 439 artigos, teses e dissertações.
-
37. New Multicomponent Reaction for the Direct Synthesis of β-Aryl-γ-nitroesters Promoted by Hydrotalcite-Derived Mixed Oxides as Heterogeneous Catalyst
A new approach based on multicomponent/domino combined reactions for the synthesis of γ-nitroesters promoted by a mixed aluminium-magnesium oxides derived from hydrotalcite-like material was developed. Different γ-nitroesters were synthesized in 15-95% yield using Meldrum's acid, aromatic aldehydes, nitromethane and different alcohols as reagents and solve
J. Braz. Chem. Soc.. Publicado em: 2017-02
-
38. Effect of Preheating on Microstructure and Tensile Properties of Friction Stir Welded AA7075 Aluminium Alloy Joints
ABSTRACT The high strength AA7075 aluminum alloy is commonly used in the aerospace components due to its exclusive mechanical properties like lightweight and high strength. This alloy cannot be welded by fusion welding techniques due to solidification cracking which severely degrade the mechanical properties of the joint. In contrast, through friction stir w
Braz. arch. biol. technol.. Publicado em: 23/01/2017
-
39. The efficacy of low-level 940 nm laser therapy with different energy intensities on bone healing
Abstract The aim of this study was to evaluate the efficacy of low-level 940 nm laser therapy with energy intensities of 5, 10 and 20 J/cm2 on bone healing in an animal model. A total of 48 female adult Wistar rats underwent surgery to create bone defects in the right tibias. Low-level laser therapy (LLLT) was applied immediately after surgery and on post-op
Braz. oral res.. Publicado em: 05/01/2017
-
40. Effect of Humidity on The Fatigue Behaviour of Adhesively Bonded Aluminium Joints
Abstract The present work focuses on the effects of water degradation on the fatigue behaviour of adhesive joints bonded with aluminium adherends. The objective of this study is to measure the influence that humidity has on the fatigue crack growth velocity of two distinct adhesives characterized using the Paris Law, using double cantilever beam (DCB) specim
Lat. Am. j. solids struct.. Publicado em: 2017-01
-
41. Analysis of precipitate density of an aluminium alloy by TEM and AFM
Abstract The quantification of nanometric precipitates in Al-Zn-Mg-Cu alloys has been performed by a series of experimental techniques. Especially in the AA7050 alloy, after ageing heat treatment, the particles responsible for the hardening become very thin. Typically, these precipitates of nanometric sizes are mainly characterized by transmission electron m
REM, Int. Eng. J.. Publicado em: 2016-12
-
42. Influence of Adherend Surface Roughness on the Adhesive Bond Strength
Abstract Surface treatment of the adherends prior to adhesive bonding plays an important role in the enhancing of strength and durability of bonded joints. In this work, an investigation on effect of adherend surface roughness on adhesive bond strength was performed. Single strap joints with different adherends (mild steel and aluminium) bonded with an epoxy
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
43. Repairing of an Engine Block Through the Cold Gas Dynamic Spray Technology
In the modern automotive industry, the maintenance of the vehicle during its life cycle is increasing in importance due to both economical and environmental considerations. A new frontier is the reparation of large parts, originally made by fusion, by the addition of material. The standard technique in the field is the use of TIG welding, but in the last few
Mat. Res.. Publicado em: 26/09/2016
-
44. Effect of Aluminium Addition on the Magnetic Properties of a Semi-Processed Electrical Steel
Aluminum is often added to electrical steels since this element causes improvement of the magnetic properties. However the addition of aluminum is usually limited to 0.30 wt%1. Therefore, this work aimed at evaluating the influence of higher levels of aluminum in the magnetic properties of semi-processed steels. To accomplish this, four types of steel were p
Mat. Res.. Publicado em: 12/09/2016
-
45. Effect of Mill Type on Morphology of AA6013 Aluminium Powder
ABSTRACT In conventional recycling method, metal chips are cast after pressing and melting in electric arc furnace. Material loss occurs during the recycling from liquid metal due to the several reasons. Direct recycling method which produces the aluminium powder from aluminium chips using mechanical mill can be an alternative to conventional recycling metho
Matéria (Rio J.). Publicado em: 2016-09
-
46. Ballistic Limit of High-Strength Steel and Al7075-T6 Multi-Layered Plates Under 7.62-mm Armour Piercing Projectile Impact
Abstract This paper presents the computational-based ballistic limit of laminated metal panels comprised of high strength steel and aluminium alloy Al7075-T6 plate at different thickness combinations to necessitate the weight reduction of existing armour steel plate. The numerical models of monolithic configuration, double-layered configuration and triple-la
Lat. Am. j. solids struct.. Publicado em: 2016-09
-
47. Characterisation and microleakage of a new hydrophilic fissure sealant - UltraSeal XT® hydro™
ABSTRACT Objectives The aim of this study was to characterise the new hydrophilic fissure sealant, UltraSeal XT® hydro™ (Ultradent Products, USA), and to investigate its in vitro resistance to microleakage after placement on conventionally acid etched and sequentially lased and acid etched molars. Material and Methods The sealant was characterised by
J. Appl. Oral Sci.. Publicado em: 2016-08
-
48. 12 mm Thick Circular Blanks of Al-killed AISI 1020 Steel -Applied for Cylindrical Cup Manufacturing by Multistage Deep Drawing with Simultaneous Ironing
Abstract In this paper a new modified processing route has been proposed for producing long cylindrical cups from 12 mm thick circular blanks of AISI 1020 steel (Aluminium (Al) -killed). In this route, flat blanks were made to preformed shape by stamping operation, followed by multistage deep drawing processes(without blank-holder and with inter-stage stress
Mat. Res.. Publicado em: 21/07/2016