Aluminium
Mostrando 25-36 de 439 artigos, teses e dissertações.
-
25. Study of friction stir spot welding on AA6063 aluminium alloy used in the ship building industry
ABSTRACT Friction stir spot welding (FSSW) is a novel process of metal joining. In the present work, the authors analysed the possibility of using this process to solve current problems in shipbuilding industry regarding small vessels by replacing the current arc welding techniques with the aforementioned process. Numerical simulation was carried out by the
Matéria (Rio J.). Publicado em: 19/07/2018
-
26. Investigation of Mechanical and Metallurgical Properties of Friction Stir Corner Welded Dissimilar Thickness AA5086-AA6061 Aluminium Alloys
In this investigation, an attempt has been made to fabricate dissimilar thickness corner joint using non-heat treatable (AA5086) and heat treatable (AA6061) dissimilar aluminium alloys by friction stir welding process with plate thicknesses of 6mm and 4mm. Three parameters and three levels were considered to conduct the experiments such as welding and rotati
Mat. Res.. Publicado em: 11/06/2018
-
27. Rheo-Squeeze Casting of High-Silicon Aluminium Alloy Pipes with Gradient Structures and Their Mechanical Properties
Three different compositions of high-Si Al alloy pipe, with a gradient structure, were produced through semi-solid rheological squeeze casting, the microstructural characteristics of which were investigated. The mechanism of gradient structure formation and the effect of acicular Fe-rich phases on liquid segregation were revealed. Meanwhile, the crystal stru
Mat. Res.. Publicado em: 11/06/2018
-
28. Effect of Heat Input on the Mechanical Behaviour of Al-Cu FSW Lap Joints
Dissimilar Al-Cu joints are desirable due to the combination of the good electrical and thermal properties of copper with the economic advantages of aluminium. However, different chemical, mechanical and thermal properties turn dissimilar welding into a challenge with traditional fusion welding techniques. Friction stir welding appears to be a good alternati
Mat. Res.. Publicado em: 28/05/2018
-
29. Microstructural and Electrochemical behaviour of Aluminium Alloy Composites Produced Using Different Sintering Techniques
Present research work analyses the effect of heating modes on the densification, microstructure and mechanical properties of aluminum alloys [65Al-20Cu-15Mn] fabricated through powder metallurgy route. Sintering of compacts using conventional, microwave and spark plasma sintering methods has been carried out at 525°C. From the results, it has been observed
Mat. Res.. Publicado em: 12/03/2018
-
30. Obtaining an Optical Trap Type Surface by Plasma Electrolytic Oxidation
High performance solar collectors are those with high selectivity surfaces, high solar radiation absorption and that do not thermally reemit to the external environment. Strategies to enhance this performance might involve surface porosity modification. In this work, a plasma treatment technique called plasma electrolytic oxidation (PEO) has been tested to p
Mat. Res.. Publicado em: 01/03/2018
-
31. Roll Bonding of Steel Net-Reinforced Aluminium Strips
The present study is dedicated to the experimental determination of strain parameters at rolling of aluminium matrix with inserted wire netting. Two types of stainless steel fabric netting with different orientation to the rolling axis were placed between two aluminium strips and hot rolled. The rolling temperature and reduction were varied to achieve the so
Mat. Res.. Publicado em: 01/02/2018
-
32. Parenteral adjuvant potential of recombinant B subunit of Escherichia coli heat-labile enterotoxin
BACKGROUND The B subunit of Escherichia coli heat-labile enterotoxin (LTB) is a potent mucosal immune adjuvant. However, there is little information about LTB's potential as a parenteral adjuvant. OBJECTIVES We aimed at evaluating and better understanding rLTB's potential as a parenteral adjuvant using the fused R1 repeat of Mycoplasma hyopneumoniae P97 ad
Mem. Inst. Oswaldo Cruz. Publicado em: 2017-12
-
33. Influence of Si Coating on Interfacial Microstructure of Laser Joining of Titanium and Aluminium Alloys
A common phenomenon in the dissimilar joints is the presence of brittle compounds in the joining interface region. The brittle phases can decrease by introduction of interlayers in the joining interface, such as silicon, that inhibits the formation of Al3Ti and AlTi3 phases in joining process between titanium and aluminium alloys. In the present work, the jo
Mat. Res.. Publicado em: 09/11/2017
-
34. Dry Sliding Wear Behaviour of Aluminium 5059/SiC/MoS2 Hybrid Metal Matrix Composites
The present study is to investigate the influence of weight percentage of silicon carbide (SiC) (5,10 %, 15%) and particle size (10,20,40µm) of SiC and constant 2% of Molybdenum disulphide(MoS2)is reinforced with aluminium matrix. Wear performance of the composite was carried out through pin-on-disc method to calculate friction coefficient and wear resistan
Mat. Res.. Publicado em: 28/09/2017
-
35. Effects of Solidification Rate in the Microstructure of Al-Si5Cu3 Aluminum Cast Alloy
Aluminium alloy Al-Si5Cu3 (319) is one of the most commonly used casting alloys for automobile components, due to its casting characteristics. Iron is the major impurity element that influences the detrimental β-phase formation in secondary aluminum alloys. In the present study, we investigated the influence of the cooling rate on the formation of iron comp
Mat. Res.. Publicado em: 20/07/2017
-
36. Growth and Characterization of AlxGa1-xAs Obtained by Metallic-Arsenic-Based-MOCVD
In this work reports results related to growth and characterization of AlxGa1-xAs epilayers, which were grown in a metallic-arsenic-based-MOCVD system. The gallium and aluminium used precursors were trimethylgallium (TMGa) and trimethylaluminium (TMAl), respectively. By photoluminescence measurements observed, that only samples grown at temperatures above 80
Mat. Res.. Publicado em: 23/03/2017