3d Modeling
Mostrando 13-24 de 363 artigos, teses e dissertações.
-
13. Comparison of 1D and 3D reservoir heat transport models and temperature effects on mass transport
RESUMO Modelos 1D e 3D de transporte de calor são comparados em um reservatório dentrítico no Brasil. Os períodos de estratificação para ambos modelos foram estimados usando índices físicos e gradientes de temperatura. O modelo tridimensional reproduz a temperatura da coluna d'água com mais acurácia, no entanto, o cálculo de índices físicos (nú
RBRH. Publicado em: 01/07/2019
-
14. The Impacts of Health Care Evaluations on the Well-Being of Low-incomers
Resumo Há uma chamada forte por pesquisas de marketing que contemplem os impactos de bens e serviços no bem-estar do consumidor, o que ganha mais vulto quando se trata de pessoas de baixa renda (Base da Pirâmide). Este artigo articula um Modelo Conceitual das relações entre avaliações de serviços de cuidado da saúde e o bem-estar do cliente, surgido
Rev. adm. contemp.. Publicado em: 27/06/2019
-
15. Depicting the 3D geometry of ore bodies using implicit lithological modeling: An example from the Horto-Baratinha iron deposit, Guanhães block, MG
Abstract The definition of geological domains is essential for mineral exploration and is traditionally done manually, section by section, in a laborious, time consuming and subjective process, to construct a 3D model. The technique referred to as implicit modeling is an option to model deposits in a fast and practical manner. This article presents the litho
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
16. Ore resource estimation based on radial based functions - Case study on União Luiz and Morro do Carrapato Gold Deposits (Alta Floresta Gold Province)
Abstract Radial basis functions can be used as an alternative method for mineral resource estimation when ordinary kriging cannot be done because it is impossible to calculate an experimental variogram. Interpolation based on radial based functions is a method that is similar to ordinary kriging. In this context, this article presents the results of gold res
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
17. Trophic dynamics (Dissolved Inorganic Nitrogen-DIN and Dissolved Inorganic Phosphorus-DIP) in tropical urban estuarine systems during periods of high and low river discharge rates
Abstract: This paper focused on the use of the biogeochemical LOICZ (Land Ocean Interactions in the Coastal Zone) to investigate the dynamics of DIN and DIP nutrients among three highly urbanized tropical estuaries (Barra das Jangadas (BJ), Recife (RE) and Timbó (TB)), located in the northeastern region of Brazil. The input data were obtained through in sit
An. Acad. Bras. Ciênc.. Publicado em: 23/05/2019
-
18. In silico prediction of the functional and structural consequences of the non-synonymous single nucleotide polymorphism A122V in bovine CXC chemokine receptor type 1
Resumo O presente estudo objetivou avaliar se o polimorfismo causal A122V promove alterações nas propriedades funcionais e estruturais da proteína receptora de quimiocina CXC do tipo 1 (CXCR1) de bovino Bos taurus por análises in silico. Duas sequências de aminoácidos da CXCR1 bovina foram selecionadas a partir do banco de dados UniProtKB/Swiss-Prot:
Braz. J. Biol.. Publicado em: 18/04/2019
-
19. Accuracy of 3D digital modeling of dental arches
RESUMO Objetivo: o objetivo do presente estudo foi verificar e comparar a precisão de modelos digitais de uma arcada dentária completa obtidos utilizando-se dois tipos de scanners e três metodologias de digitalização. Métodos: um modelo de resina feito com impressão 3D foi digitalizado em um scanner de referência (Zfx Evolution - Zimmer Biomet, Pa
Dental Press J. Orthod.. Publicado em: 2019-02
-
20. Influence of film coefficient during multicomponent diffusion – KCl/NaCl in biosolid for static and agitated system using 3D computational simulation
Abstract The influence of film coefficient formed during the diffusion of inorganic salts (NaCl and KCl) in biosolids was studied using a 3D computer modeling by Finite Elements Method (FEM) in COMSOL Multiphysics® software combined with SOM-type Artificial Neural Networks (ANN). Such tools have shown that the influence of the film formed in the biosolid/s
Food Sci. Technol. Publicado em: 07/01/2019
-
21. Influence of film coefficient during multicomponent diffusion – KCl/NaCl in biosolid for static and agitated system using 3D computational simulation
Abstract The influence of film coefficient formed during the diffusion of inorganic salts (NaCl and KCl) in biosolids was studied using a 3D computer modeling by Finite Elements Method (FEM) in COMSOL Multiphysics® software combined with SOM-type Artificial Neural Networks (ANN). Such tools have shown that the influence of the film formed in the biosolid/s
Food Sci. Technol. Publicado em: 20/12/2018
-
22. Consistency analysis of mechanical properties of elements produced by FDM additive manufacturing technology
ABSTRACT Additive manufacturing (AM) technology refers to the process of producing 3D objects by adding material in successive layers. Fused deposition modeling (FDM) is one of the AM technologies where objects are built by adding layers of melted thermoplastic filament onto the printing surface. Mechanical properties of FDM printed part depend on many influ
Matéria (Rio J.). Publicado em: 06/12/2018
-
23. Comportamiento al creep de un polímero utilizado para impresión 3D
ABSTRACT In recent years, additive construction or 3D printing technology is being widely used for manufacturing goods. This construction procedure has and will have a great industrial impact. There are several 3D printing processes, and among of them the most known is called Fused Deposition Modeling (FDM). The objective of the present paper is oriented to
Matéria (Rio J.). Publicado em: 19/07/2018
-
24. Clinical Application of Atlantoaxial Pedicle Screw Placement Assisted by a Modified 3D-Printed Navigation Template
OBJECTIVES: To investigate the primary clinical value of atlantoaxial pedicle screw placement assisted by a modified 3D-printed navigation template. METHODS: We retrospectively analyzed the cases of 17 patients treated from June 2015 to September 2016 with atlantoaxial pedicle screw placement assisted by a modified 3D-printed navigation template. All proce
Clinics. Publicado em: 19/07/2018