300m Steel
Mostrando 1-12 de 34 artigos, teses e dissertações.
-
1. Efeito da Adição de Propileno aos Gases de Proteção Convencionais na Soldagem GMAW Aplicada a Juntas de Topo e Ângulo
Resumo O presente trabalho teve por objetivo avaliar a adição de 1,3% de C3H6 ao CO2 puro e 0,6% de C3H6 à mistura de Ar+25%CO2, na soldagem de aço carbono utilizando o processo Gas Metal Arc Welding (GMAW) aplicado em juntas de topo com chanfro em V e ângulo em T. As soldas foram realizadas utilizando chapas de aço SAE 1020, arame de solda ER70S-6 de
Soldag. insp.. Publicado em: 02/12/2019
-
2. Microstructural Evolution Due to One Thermal Cycle in a Superduplex Stainless Steel ASTM A890/A890M - Grade 6A in the As-Weld and Post-Weld Heat Treatment Conditions
During welding of the superduplex stainless steels are exposed to thermal cycles, allowing precipitation of deleterious phases as well as unbalance as the ferrite and austenite phases. This work analyzed the microstructural changes taking place on a plate ASTM A890/A890M - grade 6A steel submitted to arc welding one welding of pass conducted on a flat surfac
Mat. Res.. Publicado em: 08/08/2019
-
3. Experimental studies of short concrete reinforced steel fiber beams under bending
Resumo Este estudo apresenta os resultados do rompimento de dois grupos de vigas de concreto com fibras de aço. Cada grupo foi composto de 4 vigas com vão de 300 mm, 4 com vão de 500 mm e 4 com vão de 800 mm e seção de 15 cm x 15 cm. A variação dos grupos se deu pela quantidade de fibras (I com 40 kg/m³ e II com 60 kg/m³). Foram avaliados o comport
Rev. IBRACON Estrut. Mater.. Publicado em: 20/05/2019
-
4. Corrosão em estacas metálicas de torres de energia elétrica
RESUMO Para se manter a qualidade e continuidade do fornecimento de energia é essencial monitorar a integridade da estrutura das torres de transmissão usualmente executadas em aço. Por isso, avaliou-se a corrosividade do solo na região amazônica no trecho Vila do Conde-Tucuruí́, no estado do Pará. Foi analisado a resistividade, potencial estrutura-so
Matéria (Rio J.). Publicado em: 20/05/2019
-
5. Bolted Shear Connectors Performance in Self-Compacting Concrete Integrated with Cold-Formed Steel Section
Abstract In conventional composite construction involving hot-rolled steel section, the composite action is usually achieved by using conventional headed shear studs connectors. However, use of headed studs is not practical for cold-formed steel (CFS) section due to its very thin form that is difficult to weld. A suitable bolt and nut type shear connector wa
Lat. Am. j. solids struct.. Publicado em: 2016-04
-
6. Mechanical Behavior of a Twip Steel (Twinning Induced Plasticity)
ABSTRACTA TWIP steel (0.65%C; 22%Mn; 0.28%Cr; 0.16%Si) was produced in the laboratory by melting, casting, hot forging and hot rolling. The relationship between mechanical twinning fraction and mechanical behavior of this steel was studied through tension tests at the following temperatures: 25, 300, 325, 350, 375 and 400°C. Fracture toughness was measured
Matéria (Rio J.). Publicado em: 2015-09
-
7. Effects of the administration of a catalase inhibitor into the fourth cerebral ventricle on cardiovascular responses in spontaneously hypertensive rats exposed to sidestream cigarette smoke
OBJECTIVE: Previous studies have demonstrated a relationship between brain oxidative stress and cardiovascular regulation. We evaluated the effects of central catalase inhibition on cardiovascular responses in spontaneously hypertensive rats exposed to sidestream cigarette smoke. METHODS: Male Wistar Kyoto (WKY) rats and spontaneously hypertensive rats (S
Clinics. Publicado em: 2013-06
-
8. Laser beam welding tempered 300M ultrahigh mechanical strength steel
AISI 300M ultrahigh strength steel has been used in a number of high demanding applications, such as the VLS Brazilian rocket project. This work intends to propose laser beam welding, with subsequent tempering, as a possible route for the fabrication of engineering pieces of this steel. A 2 kW fiber laser was used to produce welded coupons for metallographic
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2012-03
-
9. Utilização de técnicas eletromagnéticas para detecção de danos térmicos em aço 300M empregado em trens de pouso
Trens de pouso de aeronaves podem vir a apresentar defeitos induzidos termicamente devido a condições severas que podem ocorrer durante pousos e inspeções rotineiras em que são submetidos periodicamente. A microestrutura resultante das regiões que compreendem os defeitos pode comprometer o bom desempenho em fadiga do componente devido a alteração das
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2012
-
10. AvaliaÃÃo e ComparaÃÃo da ResistÃncia à CorrosÃo por Pites do AÃo SuperaustenÃtico AL 6XN PLUS TM e dos AÃos InoxidÃveis AustenÃticos da SÃrie AISI 304L, 316L e 317L / Evaluation and comparison of resistance to pitting corrosion of the steel superaustenitic AL 6XN PLUS â and the series austenitic stainless steels AISI 304L, 316L and 317L.
As torres de destilaÃÃo de petrÃleo sofrem corriqueiramente com problemas relacionados à corrosÃo devido ao elevado Ãndice de acidez presente no petrÃleo exigindo uma elevada resistÃncia à corrosÃo por parte dos equipamentos utilizados. Dentre os materiais empregados na fabricaÃÃo e revestimento dos equipamentos, destacam-se os aÃos inoxidÃveis
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 11/11/2011
-
11. Fragilização por hidrogênio de parafusos cementados / Hydrogen embrittlement of carburized bolts
The main aim of this work is to investigate the effects on hydrogen embrittlement of bolts due to acid pickling, baking, and strip processes performed during zinc plating. Carburized bolts type "hexagon flange head tapping screws", with 6 mm of diameter and 16 mm of thread length were organized into 39 different groups. Acid pickling was evaluated using volu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/07/2011
-
12. A study of microstructure and wear behaviour of TiB2/Al metal matrix composites
The present paper deals with the study of microstructure and wear characteristics of TiB2 reinforced aluminium metal matrix composites (MMCs). Matrix alloys with 5, 10 and 15% of TiB2 were made using stir casting technique. Effect of sliding velocity on the wear behaviour and tribo-chemistry of the worn surfaces of both matrix and composites sliding against
Latin American Journal of Solids and Structures. Publicado em: 2011