300m Steel
Mostrando 13-24 de 34 artigos, teses e dissertações.
-
13. Efeito do tamanho do abrasivo no desgaste de metais. / The effect of abrasive size on the wear resistance of metallic materials.
In this research, the effect of abrasive size on the wear resistance of five metallic materials was investigated. Abrasive wear tests using a pin test on alumina paper were carried out using abrasive sizes between 16 µm and 192 µm. The wear surface of the specimens was examined by scanning electron microscopy for identifying the wear micromechanism and the
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 08/06/2010
-
14. Effect of thermal aging conditions on the corrosion properties and hardness of a duplex stainless steel
The corrosion properties of a 22.5 wt. (%) Cr duplex stainless steel were investigated after long-term aging of 3000, 5000 and 7000 hours at 300 and 400 ºC. The corrosion resistance was measured based on mass loss in a FeCl3 10 wt. (%) solution and electrochemical measurements in a 0.1 M H2SO4 solution. The results indicate that the corrosion resistance dec
Materials Research. Publicado em: 2010-12
-
15. Environmentally induced cracking of API grade steel in near-neutral pH soil
Environmentally induced cracking of pipeline steels in contact with soil have been investigated. Different soils were prepared in order to determine their physical, chemical and bacteriological characteristics. Slow strain rate testing was carried out by using electrolytes obtained from soil samples and NS4 standard solution. Stress vs. strain curves of API
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-06
-
16. Magnetic properties and retained austenite quantification in SAE 4340 steel
Magnetic properties (coercive force and saturation magnetization) of SAE 4340 steel, heat treated in different ways, were measured in a Vibrating Sample Magnetometer. Four soaking temperatures were investigated: 860°C, 960°C, 1060°C and 1160°C. The oil-quenched samples were tempered at different temperatures between the range of 200°C and 650°C. The in
Matéria (Rio de Janeiro). Publicado em: 2009
-
17. Construção e caracterização de um detector eletroquímico para análises em fluxo
The present work describes a low-cost electrochemical "wall-jet" detector for flow analysis. The electrolytic solution enters into the cell through a tube of stainless steel (200 to 300 µm i.d), reaching to the center of the working electrode perpendicularly and then being mixed to the remaining solution in the cell, which flows under atmospheric pressure i
Química Nova. Publicado em: 2009
-
18. Biofilme de Enterococcus faecium em superficie de aço inoxidável : caracterização tecnologica, modelagem e controle por agentes sanitizantes / Biofilm of Enterococcus faecium in surface of stainless steel : modeling and control by sanitizers agents
Dentre os microrganismos que apresentam capacidade de aderir e formar biofilmes em superfícies de processamento de alimentos, como equipamentos e utensílios, estão às bactérias do gênero Enterococcus, presentes em alimentos como leite e derivados. Sua presença em queijos tem sido muito estudada por sua capacidade de conferir características tecnológ
Publicado em: 2009
-
19. Aderência bacteriana: estudo in vitro de superfície de aço inoxidável e liga de titânio-alumínio-vanádio de uso ortopédico / Bacterial adherence: an in vitro study of stainless steel and titanium-aluminium-vanadium alloy surfaces of orthopedic use
O uso de metais na fabricação de implantes ortopédicos iniciou-se nas primeiras décadas do século XX. O aumento do uso de biomateriais implantáveis aumentam também os casos de infecção. A colonização da superfície do biomaterial pode ter início no momento da inserção do corpo estranho no organismo e geralmente é causada por microrganismos da
Publicado em: 2009
-
20. Simulation of the aluminum alloy A356 solidification cast in cylindrical permanent molds
A mathematical model based on the control volume method with fixed mesh was selected in order to simulate the solidification of cylindrical castings poured in permanent steel mold. The latent heat was incorporated using the effective specific heat. The application of the model allowed us to obtain the solidification front and the temperature fields at any ti
Matéria (Rio de Janeiro). Publicado em: 2008-06
-
21. Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial
In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate hea
Publicado em: 2008
-
22. The effect of different light-curing units on tensile strength and microhardness of a composite resin
The aim of this study was to evaluate the influence of different light-curing units on the tensile bond strength and microhardness of a composite resin (Filtek Z250 - 3M/ESPE). Conventional halogen (Curing Light 2500 - 3M/ESPE; CL) and two blue light emitting diode curing units (Ultraled - Dabi/Atlante; UL; Ultrablue IS - DMC; UB3 and UB6) were selected for
Journal of Applied Oral Science. Publicado em: 2007-12
-
23. Utilização de madeira de eucalipto de pequenas dimensões na fabricação de uma ponte protendida com madeira laminada colada / Use of small-sized eucalyptus wood to build a pre-stressed bridge with glued-laminated timber
This study aimed to build and evaluate the behavior of a highway stress-laminated timber bridge deck measuring 6m in length, 3.5 m width and 0.24 m thickness submitted to a load of 13 t. The deck was built with laminations made from eucalyptus logs of various thinning-originated specimens, with a mean diameter of 2.5 m and ages ranging between 8 and 19. To b
Publicado em: 2007
-
24. AnÃlise de Textura e Propriedades MagnÃticas em AÃos Maraging 300 e 350 em VÃrias CondiÃÃes de Tratamento / Analysis of Texture and Magnetic Properties of Maraging 300 and 350 in Various Conditions of Treatment
AÃos maraging sÃo ligas Ni-Co-Mo-Ti de ultra-alta resistÃncia e vasta aplicaÃÃo que vai desde a indÃstria bÃlica e nuclear atà componentes aeronÃuticos, vasos de pressÃo e a indÃstria esportiva. Atualmente estes aÃos vÃm sendo estudados para utilizaÃÃo em rotores de alta velocidade de motores de histerese. Os aÃos maraging apresentam algumas
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 25/08/2005