Work Flow
Mostrando 1-12 de 1981 artigos, teses e dissertações.
-
1. Bayesian modeling of the maximum streamflows from the Furnas reservoir
ABSTRACT The objective of this work was to predict the maximum flow of the Furnas reservoir in the dry and wet periods. The generalized distribution of extreme values (GEV) was used with parameter estimation via Bayesian inference. Data on average daily streamflows corresponding to the years 1965 to 2017 were obtained from Hidroweb, by the National Agency fo
Engenharia Sanitaria e Ambiental. Publicado em: 2022
-
2. Structural Characteristics of Lignite Char from Different Pyrolysis Reactors and the Influence on Their Gasification Reactivity
The gasification reactivity of coal char is affected by numerous experimental variables, and char structure is one of the dominant factors. In this work, Raman spectroscopy, powder X-ray diffraction (XRD), and N2 adsorption were used to investigate the physical and chemical structure of char prepared under different pyrolysis conditions. Three kinds of pyrol
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
3. SEWAGE PERFORMANCE OF A NEW TYPE OF FLAP FILTER
ABSTRACT The drainage performance of a mesh filter determines the water consumption degree of the filter and the efficiency of the next work cycle. Through analysis, we found that the influent flow rate and the sediment content of the influent were important influencing factors. This experiment focused on the drainage time, pressure difference, and cleanline
Eng. Agríc.. Publicado em: 2021-04
-
4. TITULADOR AUTOMÁTICO EM FLUXO-BATELADA UTILIZANDO UM HARDWARE DE CÓDIGO FONTE ABERTO ARDUINO
This work describes the development of an automatic titrometric method in flow-batch with potentiometric detection using alternative and easily accessible materials. Arduino board and its modules, solenoid valves to control the flow rate, peristaltic pump to propel and suction fluids and tubes of inert material to connect the different parts of the Flow-Batc
Quím. Nova. Publicado em: 2021-03
-
5. Evaluation of mortars produced with Baosteel slag short flow (BSSF) steel slag as fine aggregate
Abstract The objective was to evaluate the influence of Baosteel slag short flow (BSSF) steel slag, a byproduct of a Brazilian steel mill, as a fine aggregate on the properties of fresh state and on the compressive strength of mortars. The experimental work was to characterize the BSSF steel slag and to produce simple mortars (only cement) and mixed mortars
Cerâmica. Publicado em: 2021-03
-
6. SEQUENTIAL MULTI-ELEMENT DETERMINATION OF TRACE-METALS IN BIODIESEL SAMPLES USING HR-CS FAAS
In this work the feasibility of sequential multi-element determination of Zn, Fe, Mg, Cu, Na, K, Cr, Al and Ca in biodiesel samples by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS) was investigated. Biodiesel samples obtained from different sources and different chemical processes were analysed. The samples were diluted w
Quím. Nova. Publicado em: 2021-02
-
7. Physical and physiological quality of rice seeds in function of drying temperature and storage
ABSTRACT The objective with the work was to evaluate, during storage, the rice seeds physical and physiological quality, cultivar IRGA 424 RI, dried with different drying air temperatures. For such, rice seeds were harvested with a moisture content of 22%. Then, they were subjected to drying in a cross-flow dryer, operating in an intermittent system and usin
Rev. Ceres. Publicado em: 2021-02
-
8. PERFORMANCE OF AIR INDUCTION SPRAY NOZZLE MODELS UNDER DIFFERENT OPERATING CONDITIONS
ABSTRACT For the successful application of phytosanitary products, it is essential to understand the spraying process well. The present work aims to evaluate the spectrum and speed of the droplets produced by different spray nozzle models with air induction, working under different operating conditions. The experiment was conducted using an entirely randomiz
Eng. Agríc.. Publicado em: 2020-12
-
9. MORPHOGENIC AND STRUCTURAL CHARACTERISTICS OF MARANDU GRASS AFFECTED BY FERTIGATION WITH TREATED SEWAGE EFFLUENT AND CUTTING HEIGHT
ABSTRACT The response of biomass flow components of forage from the interaction between fertigation with wastewater and cutting height during the year is little known. The objective of this work was to verify the responses of morphogenic and structural characteristics of Urochloa brizantha as a function of fertigation application strategies with sewage treat
Eng. Agríc.. Publicado em: 2020-12
-
10. Effects of Temperature and Concentration on the Determination of PET Viscosity
This work describes the use of experiment planning to investigate the effects of the variables temperature and concentration of the polymer solution on the viscosity test of polyethylene terephthalate (PET). For this, the response surface methodology was based on a central composite rotatable design (CCRD) to optimize the combinations of the analytical condi
J. Braz. Chem. Soc.. Publicado em: 2020-09
-
11. SPECIATION ANALYSIS OF ARSENIC IN RICE USING HIGH PERFORMANCE LIQUID CHROMATOGRAPHY COUPLED WITH HYDRIDE GENERATION ATOMIC FLUORESCENCE SPECTROMETRY (HPLC-HG-AFS)
The aim of this work was to develop a method using high performance liquid chromatography coupled with hydride generation atomic fluorescence spectrometry (HPLC-HG-AFS) for the determination and speciation analysis of the inorganic and organic species of arsenic found most often in rice samples: As(V), As(III), monomethylarsonic acid (MMA), and dimethylarsin
Quím. Nova. Publicado em: 2020-06
-
12. Methodology Development and Validation of Amphotericin B Stability by HPLC-DAD
The high worldwide consumption of antibiotics and their complex impurity profiles has drawn the attention of the scientific community to the development and validation of stability methods for these drugs. Amphotericin B is an antibiotic that is a natural fermentation product of bacterium Streptomyces nodosus, used as a broad-spectrum antifungal agent, and i
J. Braz. Chem. Soc.. Publicado em: 2020-05