Wetting Process
Mostrando 1-12 de 34 artigos, teses e dissertações.
-
1. Analysis of carbonation and hydration of BOF steel slag for application as railway ballast
Abstract The reutilization of waste is a valuable alternative for the preservation of natural resources and the environment. In this sense, Basic Oxygen Furnace (BOF) steel slag is one of the most residues generated in steel the industry. It is estimated that for each ton of steel produced, about 150 kg of steel slag is generated in the BOF process. Generall
REM, Int. Eng. J.. Publicado em: 2020-12
-
2. Plastics floatability: effect of saponin and sodium lignosulfonate as wetting agents
Abstract Froth flotation is the most common process in mineral processing. For the separation of plastic mixtures by flotation, the use of appropriate wetting agents is mandatory. The floatability of six post-consumer plastics was studied at different concentrations of the wetting agents, saponin and sodium lignosulfonate. Also, the influence of size and sha
Polímeros. Publicado em: 03/10/2019
-
3. Corrodibility and Adherence of Reinforced Concrete Rebars Electroplated with Zinc and Zinc-Nickel Alloys
Reinforced concrete is the main structural material used in the world in the construction of bridges, roads and commercial and residential buildings. One effective method for preventing corrosion of steel reinforcement is the application of galvanic coatings to the reinforcement itself. The present study evaluated the performance of three groups of reinforci
Mat. Res.. Publicado em: 15/07/2019
-
4. Analysis of the physical quality of genetically modified and conventional maize grains in the drying and wetting processes
RESUMO O objetivo deste trabalho foi avaliar a qualidade física dos grãos de milho geneticamente modificados (Herculex 30S31) em função dos processos de secagem e umedecimento em relação ao milho convencional (AG 1051). O delineamento experimental foi o inteiramente casualizado, com esquema fatorial (7x3x2), sete tempos de secagem ou umedecimento (0, 2
Rev. Ciênc. Agron.. Publicado em: 04/07/2019
-
5. Selecting chemicals for separation of ABS and HIPS in WEEE by froth flotation
Abstract The feasibility of using common chemicals to separate plastics from waste electrical and electronic equipment (WEEE) by froth flotation is investigated. Plastic waste is one of the WEEE polluters and a separation is necessary to recycle it. The most common plastics in electronic industries are acrylonitrile-butadiene-styrene (ABS) and high impact po
Polímeros. Publicado em: 10/06/2019
-
6. Membranas Compuestas: propiedades superficiales y estabilidad térmica
ABSTRACT The composite membranes were manufactured with crosslinking poly(vinyl alcohol) on polyethersulfone porous membranes by coating process. PES membranes were exposed to air plasma for the purpose of surface modification. The coating of the support membrane was carried out by using a polymer matrix with a crosslinking agent. The physico-chemical proper
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. The Bond Strength Behavior of Polymer-modified Mortars During a Wetting and Drying Process
Polymer-modified mortars are highly popular for setting exterior tile systems and low-porosity ceramic tiles because they possess greater flexibility and higher bond strengths than conventional mortars which increases cladding serviceability. However, the long-term performance of this application is not completely understood and many pathologies has been rep
Mat. Res.. Publicado em: 24/11/2015
-
8. Comportamiento a la corrosión atmosférica marina de aceros autopatinables con estructura ferrítico perlítica y ferrítico martensítica
ABSTRACTThe steel industry constantly faces the challenge of developing new and better steels for diverse needs, on of this necessities is the use of structural steels with higher corrosion resistance to marine atmospheres and improved mechanical properties than those that currently exist. Therefore, it is necessary to systematically research both the influe
Matéria (Rio J.). Publicado em: 2015-09
-
9. Control of fluid dynamics regime in spouted bed wetting process using spectral analysis / Controle do regime fluidodinâmico estável durante o processo de umedecimento de inertes em leito de jorro utilizando análise espectral
A técnica do leito de jorro têm sido utilizada em diversos processos industriais e com maior ênfase nos setores químico, alimentício e farmacêutico, visto que apresenta como principais vantagens excelentes taxas de transferência de calor e massa. Contudo, tais características estão diretamente condicionadas à manutenção do regime de jorro estáve
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/08/2012
-
10. Analysis of semi-solid processing for metal matrix composite synthesis using factorial design
The main goal in this work is to conduct a quantitative analysis of the mechanical stir casting process for obtaining particulate metal matrix composites. A combined route of stirring at semi-solid state followed by stirring at liquid state is proposed. A fractional factorial design was developed to investigate the influence and interactions of factors as: t
Materials Research. Publicado em: 31/01/2012
-
11. Caracterização de rejeitos de minério de ferro para uso em pavimentação / Characterization of iron ore tailings for use in paving
In this work it was carried out a series of laboratory tests towards chemical, mineralogical and geotechnical characterization of rejects from iron ore processing, for use in paving. Material sampling was done in specific points as they were generated during the beneficiation process along the cycle, in order to preserve their properties. The alternative app
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 21/06/2011
-
12. UTILIZAÇÃO DE ESCAMAS DO PEIXE CORVINA PARA ADSORÇÃO DE Cr(VI) EM MEIO AQUOSO CINÉTICA E TERMODINÂMICA POR CALORIMETRIA ISOTÉRMICA CONTÍNUA.
Adsorption has become a key process for the removal of very low amounts of undesirable components from waters and wastewaters and in the sense for being environmental friendly as well. This work has as aim the study of some properties of scales of Corvina fish (Micropogonias furnieiri) as a new adsorbent to remove Cr(VI) from aqueous solutions. The Corvina s
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/02/2011