Tungsten Inert Gas Welding Tig
Mostrando 1-11 de 11 artigos, teses e dissertações.
-
1. Resistência à Corrosão de Juntas Dissimilares dos Aços AISI 316L e da Liga Inconel 718
Resumo A soldagem dissimilar (Dissimilar Metal Welds – DMWs), união de dois diferentes materiais metálicos, tem muitas aplicações industriais, com destaque para trocadores de calor nas usinas nucleares. Portanto, devem resistir à corrosão e a esforços mecânicos, entre outros requisitos. Neste trabalho foi abordada a susceptibilidade à corrosão d
Soldag. insp.. Publicado em: 21/10/2019
-
2. Investigation on the Wear Properties of Ti/TiC/TiN Composite Coatings Prepared by Powder Cored Wires Through TIG Method at Nitrogen Atmosphere on Titanium Substrate
In this present study, Tungsten Inert Gas (TIG) welding and powder filled cored wires with nitrogen shielding gas were utilized to produce TiC and TiN surface composite coatings on the titanium (Ti) sheet substrate. The TIG procedure was done at same welding parameters for all of prepared samples. Phase analysis and microstructures were done by X-ray Diffrac
Mat. Res.. Publicado em: 15/04/2019
-
3. Mechanical and Corrosion Properties of a Duplex Steel Welded using Micro-Arc or Laser
Duplex stainless steels have been extensively used in parts that are subject to corrosive environments and that have high mechanical strength requirements. Welding usually distorts the well-balanced austenite-ferrite ratio, and can produce brittle intermetallic phases; therefore, post-welding heat treatments are usually required. For applications where post-
Mat. Res.. Publicado em: 2015-08
-
4. Efeito do desajuste marginal, tipo de soldagem e material do parafuso sobre a força de destorque de parafusos protéticos e tensões induzidas aos pilares / Effect of marginal misfit, welding type and screw material on the strength of the detorque prosthetic screws and stress induced the abutments
O objetivo neste estudo foi analisar as tensões induzidas aos análogos de pilares protéticos, utilizando-se strain gauges; e avaliar a força de destorque de parafusos protéticos (ouro e titânio) em infraestruturas fundidas em titânio comercialmente puro (Ti cp), antes e após os procedimentos de soldagem laser e TIG (tungsten inert gas). Foram confecc
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/04/2012
-
5. Mechanical strength and analysis of fracture of titanium joining submitted to laser and tig welding
This study compared the tensile strength and fracture mechanism of tungsten inert gas (TIG) welds in cylindrical rods of commercially pure titanium (cp Ti) with those of laser welds and intact samples. Thirty dumbbell-shaped samples were developed by using brass rods as patterns. The samples were invested in casings, subjected to thermal cycles, and position
Mat. Res.. Publicado em: 09/10/2012
-
6. Distribuição de tensões e resistência mecânica de infraestruturas de Ni-Cr-Ti sobre implantes após soldagem a laser ou TIG / Stress distribution and mechanical strength of the infrastructures of Ni-Cr-Ti implant after laser or TIG welding
O objetivo neste estudo foi avaliar, por meio da análise fotoelástica e teste de resistência à flexão, as técnicas de soldagem a Laser e TIG (Tungsten Inert Gas) na confecção de infraestruturas implantossuportadas de NiCrTi. Três grupos foram formados com 5 amostras cada: infraestruturas fundidas em monobloco, soldadas a Laser ou TIG. O modelo fotoe
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 04/02/2011
-
7. Avaliação da influência dos parâmetros do processo de soldagem TIG sobre a qualidade de uma peça fabricada em aço elétrico silicioso / Influence of TIG welding process parameters on the quality of a piece fabricated with silicon electrical steel
The TIG welding process (Tungsten Inert Gas), also known as GTAW (Gas Tungsten ArcWelding), is the most commonly used process for welding of thin plates where there is a need for an excellent control of the temperature applied on the piece. This paper presents a study carried out in partnership between the Department of Graduate Studies in Scienceand Materia
Publicado em: 2010
-
8. Fracture strength of different soldered and welded orthodontic joining configurations with and without filling material
The aim of this study was to compare the mechanical strength of different joints made by conventional brazing, TIG and laser welding with and without filling material. Five standardized joining configurations of orthodontic wire in spring hard quality were used: round, cross, 3 mm length, 9 mm length and 7 mm to orthodontic band. The joints were made by five
Journal of Applied Oral Science. Publicado em: 2008-10
-
9. Mechanic resistance and marginal misfit of pure Ti submitted to two welding methods TIG and Laser / Resistência mecânica e desajuste marginal do titânio comercialmente puro submetido a dois métodos de soldagem: TIG e Laser
O objetivo deste trabalho foi avaliar o efeito da soldagem TIG ("tungsten inert gas") e compará-la com soldagem a laser, em hastes cilíndricas e supra-estruturas implantosuportadas, confeccionadas em titânio comercialmente puro (Ti cp) por meio dos ensaios de resistência mecânica (tração e flexão) e desajuste marginal, respectivamente. Foram confecci
Publicado em: 2008
-
10. Efeito de diferentes tipos de soldagem na resistência à tração de estruturas fundidas com ligas de Ni-Cr / Effects of different types of welding on the tensile strenght of NI-Cr structures
The development of metallic prosthetic framework in oral rehabilitation, involves critical processes specially related to casting and welding. The objective of this work was to evaluate the tensile strength of cast plates (monobloc) with three different welding methods: conventional welding (torch), laser welding and TIG welding (tungsten inert gas). Eighty
Publicado em: 2007
-
11. Avaliação da resistência flexural entre diferentes métodos de soldagem: chama direta - TIG - Laser / Evaluation of the flexural strength among different welding methods: Brazing - TIG - Laser.
A técnica de soldagem apresenta vantagem de união de partes metálicas que permite melhora na adaptação e uniformidade na distribuição das forças mastigatórias, minimizando falhas no tratamento reabilitador. O objetivo foi avaliar a resistência flexural entre três métodos de soldagem diferentes: Chama Direta a maçarico, método TIG - Tungstênio
Publicado em: 2007