Tension Distribution
Mostrando 1-12 de 128 artigos, teses e dissertações.
-
1. Acupuncture in the treatment of temporomandibular muscle dysfunction
RESUMO JUSTIFICATIVA E OBJETIVOS: A disfunção temporomandibular consiste em dores não dentárias frequentes na região orofacial, de origem multifatorial e de tratamento interdisciplinar. Entre esses tratamentos está a acupuntura. O tratamento da disfunção temporomandibular atua tanto no relaxamento muscular quanto no controle da dor, sistemicamente b
BrJP. Publicado em: 02/12/2019
-
2. Secondary healing strategy for difficult wound closure in invasive vulvar cancer: a pilot case-control study
OBJECTIVES: Despite the number of surgical advances and innovations in techniques over time, radical vulvectomy frequently results in substantial loss of tissue that cannot be primarily closed without tension, the mobilization of surrounding tissues or even the rotation of myocutaneous flaps. The aim of this study was to evaluate the feasibility of leaving
Clinics. Publicado em: 02/09/2019
-
3. Fatigue Failure Analysis on Precracked 304 Stainless Steel Components Repaired by Laser with Addition of Nanocomposites
Abstract The service life of components can be extended by repairing fatigue crack with laser so as to improve resource utilization rate. However, the effect of laser repair may be influenced by the instability of laser treatment. To investigate the addition of nanocomposites on the laser repairing effect, fatigue test under uniaxial tension was carried out
Soldag. insp.. Publicado em: 16/05/2019
-
4. Two-Dimensional Numerical Model of the Fracture Process in Steel Fibre Reinforced Concrete with the Continuum Strong Discontinuity Approach and Functional Data Analysis
Abstract This paper presents the formulation of a two-dimensional numeri-cal model able to describe the fracture process in structural mem-bers of steel fibre reinforced concrete (SFRC) from the volume ratio of the fibres and the mechanical properties of the compo-nents: a concrete matrix and a set of steel fibres with a random orientation. The relationship
Lat. Am. j. solids struct.. Publicado em: 08/04/2019
-
5. EFFECT OF NOZZLES, APPLICATION RATES, AND ADJUVANTS ON SPRAY DEPOSITION IN WHEAT CROPS
ABSTRACT The use of insecticides is common in pest management in wheat crops but may lead to higher production costs and environmental contamination. Therefore, a more comprehensive and uniform distribution of plant protection products in the desired target is recommended. The objective of this study is to evaluate the effect of different spray nozzles, appl
Eng. Agríc.. Publicado em: 2019-02
-
6. Soil Water Retention Curve as Affected by Sample Height
ABSTRACT: The soil water retention curve is one of the main instruments to assess the soil physical quality and to improve soil management. Traditionally, the equipment most used in the laboratory to determine the retention curve has been Haines funnels and Richards chambers. An important factor to which little attention has been given in the use of these eq
Rev. Bras. Ciênc. Solo. Publicado em: 14/11/2018
-
7. Fabricación de espumas de cobre por pulvimetalurgia
ABSTRACT A method for the fabrication of copper foams by powder metallurgy, employing carbamide beads as space holders, is presented. These are removed by water dissolution before sintering the compact. The method allows for a precise control of the cell characteristics (size, shape and distribution) within an interconnected porosity. The use of metal powder
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Gradientes de orientación en cercanías del borde de grano estudiados por EBSD
ABSTRACT The goal of this study is the evaluation of local misorientation, its distribution and orientation gradient in the microstructural development of a deep drawing quality steel sheet (AKDQ). The microstructure is characterized at sub-grain level spatial resolution using Electron Backscatter Diffraction (EBSD) in samples submitted to interrupted uniaxi
Matéria (Rio J.). Publicado em: 19/07/2018
-
9. Experimental and numerical investigation on the dumbbell-shaped specimen of concrete-like materials under tension
Abstract Mortar is an important component of concrete. It is of great significance to obtain its tensile properties accurately. The structure heterogeneity of mortar specimens is high. Specimens are prone to fracture nearby interfaces between specimens and loading plates because of the inhomogenous stress distribution during the testing, which leads that ef
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
10. Influence of shear lag coefficienton circular hollow sections with bolted sleeve connections
Abstract The circular hollow sections (CHS) are being widely employed in steel structures around the world, increasing the development of new researches. This article proposes an innovative connection model for circular hollow sections that facilitates and reduces the assembly cost of hollow section structures. The proposed connection is a tube sleeve, used
REM, Int. Eng. J.. Publicado em: 2017-12
-
11. Personal, particular y político: la producción del bien público en la práctica política cotidiana
Abstract The purpose of the article is to study, through the activity of those in office, the actual practices in the production of the “common good”, understood as the distribution of public goods to the citizens. The interest arises from the tension between politicians ideal behavior -according to universal and publicly orientated rules - and an actual
Rev. Sociol. Polit.. Publicado em: 2017-09
-
12. HOW TO FORMULATE A STABLE AND MONODISPERSE WATER-IN-OIL NANOEMULSION CONTAINING PUMPKIN SEED OIL: THE USE OF MULTIOBJECTIVE OPTIMIZATION
Abstract The multiobjective optimization method was applied in order to improve the droplet size distribution and stability of water-in-oil emulsions composed of sunflower and pumpkin seed oils as continuous phase, polyglycerol polyricinoleate as emulsifier, water as dispersed phase and sodium chloride as co-stabilizer (lipophobe). Three composition factors
Braz. J. Chem. Eng.. Publicado em: 2016-12