Steel Reinforcement Design
Mostrando 1-12 de 27 artigos, teses e dissertações.
-
1. Optimum design of steel columns filled with concrete via genetic algorithm: environmental impact and cost analysis
Abstract The use of concrete-filled tubular columns as part of structural systems has steadily increased throughout the years. The growing demand for structural elements of this nature is a direct result of the possibility to use various cross-section shapes that have increased strength, along with resistance to fire and other corrosive agents. The main obje
REM - International Engineering Journal. Publicado em: 2022
-
2. Optimized dimensioning of steel-concrete composite beams
Resumo As seções mistas de aço e concreto estão cada vez mais sendo utilizadas na construção civil, tanto no cenário mundial quanto no Brasil. O trabalho conjunto do perfil de aço e da laje de concreto aumenta consideravelmente o desempenho do elemento estrutural misto devido ao aproveitamento das vantagens de cada material. Neste trabalho, é utiliz
Rev. IBRACON Estrut. Mater.. Publicado em: 13/12/2019
-
3. About the use of semi-continuity in simply supported composite steel and concrete beams, to remove fireproof coatings for standard-fire resistance requirement of less than 30 minutes
Resumo Estudos anteriores do comportamento sob ação do incêndio de vigas mistas de aço e concreto, sem instabilidades locais (ditas compactas), considerando a rigidez à flexão nos apoios fornecida pela armadura negativa longitudinal à viga (semicontinuidade), mostraram que não é possível justificar a ausência de revestimento contra fogo para tempo
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
4. Optimized design of RC deep beams based on performance metrics applied to strut and tie model and in-plane stress conditions
Abstract Deep beams do not behave according to classical beam theory. The nonlinearity of strain distribution within these elements requires application of strut and tie models (STM) or other alternatives to evaluate the complex stress field. Although the design of these elements is a common task for structural engineers, limited research is found on assessi
Lat. Am. j. solids struct.. Publicado em: 22/08/2019
-
5. Evaluation of the resistance of trussed slabs with steel formwork in cold formed U profile
Abstract In the last decades, the modernization in structural engineering has increased the use of steel-concrete composite and hybrid systems for slabs, when the adherence in the interface of the materials is present or not, respectively. In addition to the traditional steel deck, a similar solution for precast trussed slabs has been used for small construc
Lat. Am. j. solids struct.. Publicado em: 12/08/2019
-
6. Slabs strengthened for punching shear with post-installed steel and CFRP connectors
Resumo Acidentes estruturais por punção vêm sendo relatados em edifícios com lajes lisas. As recomendações de projeto apresentadas pelas normas podem levar a estimativas de resistência à punção divergentes para situações semelhantes. Além disso, não são apresentadas orientações para o dimensionamento do reforço à punção de lajes existent
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
7. Numerical Investigation of Tension Reinforcement Lap Length of Eurocode 2 Using a Four-Point Beam Loading System
Abstract This report presents a computational research on Eurocode 2 (EC2) tension lap lengths (lo) design in a normally reinforced concrete beam, using ANSYS Workbench simulation software program by simulating a laboratory 4-point beam loading test system under static loading(discrete model approach). A typical 4-point laboratory setup loading system was mo
Lat. Am. j. solids struct.. Publicado em: 27/06/2019
-
8. Finite Element Analysis of Reinforced Concrete Beam-Column Connections with Governing Joint Shear Failure Mode
Abstract Reinforced concrete (RC) beam-column connections especially those without transverse reinforcement in joint region can exhibit brittle behavior when intensive damage is concentrated in the joint region during an earthquake event. Brittle behavior in the joint region can compromise the ductile design philosophy and the expected overall performance of
Lat. Am. j. solids struct.. Publicado em: 2017-08
-
9. Displacement ductility for seismic design of RC walls for low-rise housing
The paper compares and discusses displacement ductility ratios of reinforced concrete walls typically used in one- and two-story houses. Ductility is investigated by assessing response measured on 39 walls tested under shaking table excitations and quasi-static lateral loads. Variables studied were the height-to-length ratio and walls with openings, type of
Lat. Am. j. solids struct.. Publicado em: 2014-08
-
10. Avaliação estatística do erro de modelos de resistência para elementos lineares de concreto armado da ABNT NBR 6118:2007 / Statistical evaluation of resistance modelling error for linear elements of concrete structures of ABNT NBR 6118:2007
In a design of structures, it should be considered the intrinsic uncertainties to the present variables in the structure and in the structural concept, such as intensity and action distribution, mechanic properties of the material, geometric parameters of the structure and structural analysis and calculus models. Thus, the structural safety can only be measu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 03/08/2012
-
11. Diretrizes de projeto para melhorar a produtividade na montagem de componentes pré-cortados e pré-dobrados de aço para estruturas de concreto armado de edifícios. / Project guidelines to improve productivity in the assembly of cut and bent steel pieces for structures of reinforced concrete of buildings.
Este trabalho discute caminhos para tornar o projeto de detalhamento da armadura um indutor da melhoria da produtividade da mão-de-obra no serviço de armação. Uma revisão bibliográfica inicial precede a apresentação de estudos de campo, que foram realizados para se entender como a produtividade em armação varia. Tal entendimento (expresso na forma
Publicado em: 2009
-
12. COMPORTAMENTO DE VIGAS DE CONCRETO ARMADO REFORÇADAS COM CFC SUJEITAS A CARGA DE IMPACTO / BEHAVIOR OF REINFORCED CONCRETE BEAMS STRENGTHENED WITH CFC UNDER IMPACT LOADING
An experimental study on the behavior of reinforced concrete beams strengthened in flexure with CFC under impact load was carried out in this work. The main objective was to investigate the effects of the loading rate on the strength of the beams. The variables were the loading rate and the ratio of fiber to steel reinforcement cross sections. All beams were
Publicado em: 2008