Steel And Concrete
Mostrando 13-24 de 253 artigos, teses e dissertações.
-
13. Study of the influence of compressive strength concrete on columns during the design of a multi-floor building
Resumo Este trabalho tem como objetivo analisar a influência da resistência à compressão do concreto em pilares no dimensionamento de um edifício de múltiplos pavimentos, utilizando a ferramenta computacional CAD/TQS. As resistências dos pilares foram variadas em uma razão de 5 MPa, de 35 MPa até 90 MPa, sendo que os demais elementos estruturais per
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
14. Case study: influence of performance levels of ABNT NBR 15575 without consumption of materials used in reinforced concrete structures
Resumo O setor da construção civil ainda discute a consequência da Norma de Desempenho nas edificações habitacionais. Segundo a ABNT NBR 15575 [1], os sistemas que compõem edificações residenciais necessitam atingir os requisitos mínimos de desempenho. Dentre os sistemas, o estrutural deve atender a uma Vida Útil de Projeto (VUP) mínima de 50 anos
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
15. Reinforced concrete corbels strengthened with external prestressing
Resumo As estruturas em concreto podem exigir, ao longo de sua vida útil, o aumento da capacidade de carga devido a eventuais mudanças de utilização. Nesse contexto, os consolos podem ser considerados elementos estruturais que apresentam grandes desafios para a instalação de alternativas de reforço. Tal dificuldade é decorrente do fato de que a capac
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
16. Uma abordagem experimental e numérica para determinação de curvas de compressão para concreto simples e reforçados com fibras de aço
RESUMO A curva tensão-deformação do concreto é importante para o dimensionamento de estruturas, pois por meio dela é possível obter sua resistência à compressão, sua deformação de pico, o módulo de elasticidade e a tenacidade do concreto. Entretanto, essa é uma propriedade que não é comumente determinada nos ensaios de controle de qualidade do
Matéria (Rio J.). Publicado em: 16/09/2019
-
17. An Anchorage System for Enhanced Bond Behavior between Carbon Fiber Reinforced Polymer Sheets and Cracked Concrete
Abstract The contribution of CFRP wraps, as an anchorage system, to enhancing bond behavior between CFRP sheet and cracked concrete, was investigated. Thirty six concrete blocks (150 x 150 x 200 mm) were cast with 3ϕ12 mm steel bars embedded laterally at different spacing along the 200-mm-dimension. Half of the moist-cured blocks were subjected to a cyclic
Lat. Am. j. solids struct.. Publicado em: 05/09/2019
-
18. Optimized design of RC deep beams based on performance metrics applied to strut and tie model and in-plane stress conditions
Abstract Deep beams do not behave according to classical beam theory. The nonlinearity of strain distribution within these elements requires application of strut and tie models (STM) or other alternatives to evaluate the complex stress field. Although the design of these elements is a common task for structural engineers, limited research is found on assessi
Lat. Am. j. solids struct.. Publicado em: 22/08/2019
-
19. Some Aspects of Numerical Modeling of Steel-Concrete Composite Beams with Prestressed Tendons
Abstract Aspects about the numerical modeling of three-dimensional prestressed steel-concrete composite beams by using the finite element (FE) method are highlighted and commented in this work. Emphasis is given to the numerical treatment of bonded and unbonded tendons. The proposed modeling technique uses curved beam and catenary elements for simulating int
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
20. Evaluation of the resistance of trussed slabs with steel formwork in cold formed U profile
Abstract In the last decades, the modernization in structural engineering has increased the use of steel-concrete composite and hybrid systems for slabs, when the adherence in the interface of the materials is present or not, respectively. In addition to the traditional steel deck, a similar solution for precast trussed slabs has been used for small construc
Lat. Am. j. solids struct.. Publicado em: 12/08/2019
-
21. Plate with holes as shear connector in cold formed steel composite beams
Resumo Buscando compatibilizar as estruturas em perfil formado a frio com os sistemas de piso com pré-laje, foi proposta nesse trabalho uma alternativa de conector de cisalhamento para vigas mistas compostas por perfil formado a frio que visa maximizar a área disponível para apoio das pré-lajes durante o processo construtivo. Trata-se de um conector em c
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
22. Corrodibility and Adherence of Reinforced Concrete Rebars Electroplated with Zinc and Zinc-Nickel Alloys
Reinforced concrete is the main structural material used in the world in the construction of bridges, roads and commercial and residential buildings. One effective method for preventing corrosion of steel reinforcement is the application of galvanic coatings to the reinforcement itself. The present study evaluated the performance of three groups of reinforci
Mat. Res.. Publicado em: 15/07/2019
-
23. Seismic Upgrading of Exterior Reinforced Concrete Frame with Small Column and Joint Area Using Externally Attached Steel Column
Abstract This paper presents cyclic load test of five exterior reinforced concrete frames. All the specimens represent a substandard single-span, low-rise reinforced concrete frame building which behaves a weak column-strong beam mechanism under a strong seismic loading. The first three exterior frames M1, M2 and M3 were designed for the joint shear critical
Lat. Am. j. solids struct.. Publicado em: 10/07/2019
-
24. EXPERIMENTAL INVESTIGATION ON CONCRETE FILLED STEEL TUBULAR COLUMN TO FOUNDATION CONNECTIONS SUBJECTED TO COMBINED AXIAL AND LATERAL CYCLIC LOADING
Abstract This study focuses on performance of CFT column to foundation connections subjected to combined axial and lateral cyclic loading. Experimental investigations were carried out on five specimens with exposed column base and embedded column base connections. The parameters considered were number of stiffeners and embedment depth of CFT column. The forc
Lat. Am. j. solids struct.. Publicado em: 01/07/2019