Stabilized Zirconia
Mostrando 1-12 de 48 artigos, teses e dissertações.
-
1. Sintering mechanisms of partially stabilized zirconia (TZ3Y) with ZnO and Co3O4 as sintering additives
Abstract In this work, the sintering mechanisms of 3 mol% yttria-stabilized zirconia (TZ3Y) and TZ3Y containing 0.3 wt% of ZnO or Co3O4 were analyzed by determining the apparent activation energy of sintering from dilatometry data and observing the evolution of microstructure. Dilatometry test was performed at a heating rate ranging from 5 to 20 °C/min from
Cerâmica. Publicado em: 2021-06
-
2. ANODES FOR SOFC: REVIEW OF MATERIAL SELECTION, INTERFACE AND ELECTROCHEMICAL PHENOMENA
This paper presents a comprehensive interface and electrochemical phenomena review of different anodes for SOFC. In this way, it was possible to select some mixed electronic and ionic conductor materials alternatives to the conventional anode, Ni-YSZ conductor. New materials must present a satisfactory electronic and ionic conductivity at intermediate temper
Quím. Nova. Publicado em: 2021-01
-
3. Preparation and characterization of yttria stabilized zirconia (YSZ) films deposited by dip-coating on LSM-YSZ substrate with different proportions
ABSTRACT In this work, sol-gel/dip-coating process for obtaining yttria stabilized zirconia (YSZ, ZrO2–8% Y2O3) films deposited onto LSM-YSZ (lanthanum strontium manganite (LSM, La0.7Sr0.3MnO3) mixed with YSZ) with different proportions (20/80, 50/50, 80/20) was investigated. The films were deposited on substrate varying the number of layers deposited. LSM
Matéria (Rio J.). Publicado em: 25/11/2019
-
4. Influence of Yttria-Stabilized Zirconia on Microstructure and Electrical Properties of Doped Lanthanum Gallate
Lanthanum gallate with partial substitutions for strontium and magnesium shows higher ionic conductivity than traditional ionic conductors such as yttria-stabilized zirconia (8YSZ), and has been considered for application as solid electrolyte and electrode in Solid Oxide Fuel Cells operating at intermediate temperatures (500-700ºC). Parallel to the developm
Mat. Res.. Publicado em: 01/08/2019
-
5. Fracture Load and Failure Mode of CAD-on Ceramic Structures
Resumo Este estudo avaliou a carga de fratura (Cf) e o modo de falha de estruturas cerâmicas fabricadas pela técnica CAD-on (Ivoclar Vivadent), testando as hipóteses de que a Cf das estruturas multicamadas é governada pela resistência da cerâmica de cobertura e o lascamento é mais frequente nas estruturas em multicamadas do que em monolíticas. Corpos
Braz. Dent. J.. Publicado em: 22/07/2019
-
6. A new approach for Y-TZP surface treatment: evaluations of roughness and bond strength to resin cemen
Abstract Objective This study aims to evaluate the effect of sonochemical treatment on the surface of yttria-stabilized tetragonal zirconia (Y-TZP) before and after the final sintering. Material and Methods Twenty-eight Y-TZP discs were divided into four groups (n=7), according to surface treatment: PRE: pre-sintering sonication with 30% nominal power fo
J. Appl. Oral Sci.. Publicado em: 11/04/2019
-
7. Mechanical behavior of yttria-stabilized tetragonal zirconia polycrystal: Effects of different aging regimens
Abstract This study aimed to characterize and compare the effect of different aging regimens on surface characteristic (topography and roughness), structural stability (phase transformation) and mechanical performance (Weibull analysis) of a Y-TZP ceramic. Discs (15 × 1.2 mm; VITA In-Ceram YZ) were prepared according to ISO 6872-2015 for biaxial flexural st
Braz. oral res.. Publicado em: 07/12/2017
-
8. Influence of additives on phase stabilization of scandia-doped zirconia
ABSTRACT The effects of small additions of tin, zinc, calcium and boron oxides on phase composition and electrical conductivity of zirconia-10 mol% scandia were investigated. Compounds containing 1 mol% zinc, tin and calcium oxides and 1, 3 and 5 wt.% boron oxide were prepared by solid state reaction and characterized by X-ray diffraction, density measuremen
Matéria (Rio J.). Publicado em: 01/06/2017
-
9. Optimization of spin-coated electrodes for electrolyte-supported solid oxide fuel cells
ABSTRACT Electrodes for electrolyte-supported solid oxide fuel cells (SOFC's) were fabricated by spin coating. Strontium-doped lanthanum manganite (LSM) cathode and nickel yttria-stabilized zirconia cermet anodes were synthesized and processed for enhanced deposition conditions. The influence of electrode microstructural parameters was investigated by a syst
Matéria (Rio J.). Publicado em: 22/05/2017
-
10. Effect of La 0.8 Sr 0.2 MnO 3 powder addition in the precursor solution on the properties of cathode films deposited by spray pyrolysis
ABSTRACT Films of lanthanum strontium manganite, LSM (La0.8Sr0.2MnO3) were deposited on yttria stabilized zirconia (YSZ) substrates by different methods aiming to establish the most suitable route to prepare cathodes for solid oxide fuel cells (SOFC). Samples were obtained by using a solution of lanthanum, strontium and manganese nitrates or a dispersion of
Matéria (Rio J.). Publicado em: 11/05/2017
-
11. Synthesis and Characterization of Yttrium Stabilized Zirconia Nanoparticles
Yttria stabilized zirconia (YSZ) nanoparticles were synthesized by the co-precipitation method. The crystallinity, morphological and optical properties of the YSZ nanoparticles were studied by using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-Raman, photoluminescence (PL) spectrum analyses. The grai
Mat. Res.. Publicado em: 07/06/2016
-
12. Microstructural and Electrical Features of Yttrium Stabilised Zirconia with ZnO as Sintering Additive
Adding ZnO reduces sintering temperature of yttria stabilized zirconia. Adding up to 0.5 wt% of ZnO is possible to densify to 8 mol% yttria stabilized zirconia (TZ8Y) to 95% of relative density at 1300 °C, besides, the electrical conductivity increases about 30% at 800 °C when compared to pure TZ8Y with the same relative density and average grain size. The
Mat. Res.. Publicado em: 16/02/2016