Simulation And Permeability
Mostrando 1-12 de 46 artigos, teses e dissertações.
-
1. Coupled numerical simulation of a tailings deposit by FEM
Abstract Researchers have found that a valuable alternative for predicting the mechanical behavior of landfill construction is numerical simulation based on the finite element method. The results of such a numerical simulation for a sandy tailings deposit from the iron mining coupling flow and deformation are presented herein. This study investigates the inf
REM, Int. Eng. J.. Publicado em: 2019-03
-
2. A High Gain and Directivity Bow Tie Antenna Based on Single-Negative Metamaterial
Abstract This paper presents an antenna loaded with metamaterial to enhance its gain and directivity to improve the performance of a ground-penetrating radar system (GPR). We adjusted the parameters of the antenna to change its equivalent capacitance and inductance and applied an operating frequency of 0.5 GHz-1.2 GHz to create an ultra-wideband antenna. On
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2018-06
-
3. Performance Prediction of Microwave Absorbers Based on POMA/Carbon Black Composites in the Frequency Range of 8.2 to 20 GHz
ABSTRACT: This paper presents a comparative study involving experimental and numerical behaviors of radar absorbing materials (RAM), based on conducting composites of poly(o-methoxyaniline) (POMA) and carbon black (CB). Samples of POMA/CB in epoxy resin matrix were prepared. First, these samples were experimentally characterized by electric permittivity and
J. Aerosp. Technol. Manag.. Publicado em: 29/03/2018
-
4. Transverse permeability determination and influence in resin flow through an orthotropic medium in the RTM process
ABSTRACT Resin Transfer Molding (RTM) process is commonly used to produce high quality polymeric composites with simple or complex geometries in small to large sizes. In RTM process a preformed reinforcement is positioned inside the mold cavity. This dry reinforcement is actually a fibrous porous media whereby resin will flow. The mold is then closed and res
Matéria (Rio J.). Publicado em: 20/07/2017
-
5. 3-D Geological modelling: a siliciclastic reservoir case study from Campos Basin, Brazil
Abstract Reservoir static modelling plays a fundamental role in the evaluation phase of a petroleum field. Integrated modelling allows a better understanding of how the local geology and depositional systems are related through the distribution of facies and petrophysical properties within the reservoir. In this study, geological static models of the silicic
REM, Int. Eng. J.. Publicado em: 2016-12
-
6. 3D COMPOSITIONAL RESERVOIR SIMULATION IN CONJUNCTION WITH UNSTRUCTURED GRIDS
Abstract In the last decade, unstructured grids have been a very important step in the development of petroleum reservoir simulators. In fact, the so-called third generation simulators are based on Perpendicular Bisection (PEBI) unstructured grids. Nevertheless, the use of PEBI grids is not very general when full anisotropic reservoirs are modeled. Another p
Braz. J. Chem. Eng.. Publicado em: 2016-06
-
7. An experimental simulation model for coated paper drying
Due to the lack of information regarding the phenomena of mass, heat, and momentum transfer in coated paper drying, substantial research work still needs to be done. A simulation model for coated paper drying is introduced which integrates heat and mass transfer mechanisms. In the model, the coated paper was assumed to have 3 layers (coated layer, wet and dr
Braz. J. Chem. Eng.. Publicado em: 2013-09
-
8. A reinserção dos cursos de água em áreas urbanas. Estudo de caso: Microbacia do Córrego Jataí - Uberlândia /MG / The reinsertion of the watercourses in urban areas. Case study: the Stream watershed Jataí - Uberlândia/MG
The main objective of this work is to promote the reinsertion of urban water in the context of physical and territorial planning, in the cities, through the study of the watershed of Jataí stream in Uberlândia-MG. Pursuiting the rebalancing of the waters with the urban environment, this work promote the connectivity and physical strengthening of the relati
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/01/2012
-
9. Experimental measurements and numerical simulation of permittivity and permeability of Teflon in X band
Abstract Recognizing the importance of an adequate characterization of radar absorbing materials, and consequently their development, the present study aims to contribute for the establishment and validation of experimental determination and numerical simulation of electromagnetic materials complex permittivity and permeability, using a Teflon® sample. The
J. Aerosp. Technol. Manag.. Publicado em: 2011-04
-
10. Two-dimensional control volume modeling of the resin infiltration of a porous medium with a heterogeneous permeability tensor
Resin Transfer Molding (RTM) is a polymer composite processing technique widely used in the aeronautics and automotive sectors. This paper describes the numerical simulation of the RTM process where Darcy’s law was used for the mathematical formulation of the problem. A control volume finite element method was used for the determination of pressure gradien
Publicado em: 2011
-
11. Simulação de Fluxo no Meio Poroso Utilizando o Fluent
A complexidade do fenômeno do fluxo de um fluido em meios porosos causa uma dificuldade em sua descrição explícita. Diferente nos casos em que o fluxo se dar através de uma tubulação, onde é possível medir o comprimento e diâmetro da tubulação, bem como determinar sua capacidade de escoamento em função da pressão, a qual é uma tarefa complica
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/06/2010
-
12. Microwave absorbing paints and sheets based on carbonyl iron and polyaniline: measurement and simulation of their properties
Abstract: This paper presents the processing and characterization of electromagnetic radiation absorbing paints and sheets based on magnetic and dielectric materials dispersed in polymeric matrices. Two different paint formulations containing carbonyl iron and/or polyaniline, using polyurethane as matrix, were prepared. Silicone sheets were also produced wit
J. Aerosp. Technol. Manag.. Publicado em: 2010-04