Punching Shear
Mostrando 1-12 de 17 artigos, teses e dissertações.
-
1. Slabs strengthened for punching shear with post-installed steel and CFRP connectors
Resumo Acidentes estruturais por punção vêm sendo relatados em edifícios com lajes lisas. As recomendações de projeto apresentadas pelas normas podem levar a estimativas de resistência à punção divergentes para situações semelhantes. Além disso, não são apresentadas orientações para o dimensionamento do reforço à punção de lajes existent
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
2. Shear strength analysis of slabs without transverse reinforcement under concentrated loads according to ABNT NBR 6118:2014
Resumo A solicitação por cargas parcialmente distribuídas em lajes sem armadura transversal, frequente em tabuleiros de pontes, resulta na propagação horizontal da força cortante em direção aos apoios, situação na qual nem toda a largura da laje é mobilizada. Por esta razão, os modelos de resistência à força cortante de vigas e de resistência
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
3. Aspects of Finite Element Modeling of Punching Shear Behavior of Reinforced Concrete Flat Slabs
Abstract A series of nonlinear FE analyses was conducted in this paper to model the punching shear failure of RC flat slabs. The analyses were carried out in the software DIANA using three-dimensional continuum elements. These analyses involve the test of different modeling choices in order to evaluate their influences on punching shear failure modeling. The
Lat. Am. j. solids struct.. Publicado em: 04/10/2018
-
4. Failure Analysis of Polypropylene Fiber Reinforced Concrete Two-Way Slabs Subjected to Static and Impact Load Induced by Free Falling Mass
Abstract The impact resistance of concrete is considered as poor due to a relatively energy dissipating characteristics and tensile strength. Therefore, this paper investigates the feasibility of using polypropylene fibers (PF) to enhance punching shear capacity of reinforced concrete (RC) two-way slabs subjected to drop-weight impacts. The evaluated parame
Lat. Am. j. solids struct.. Publicado em: 23/04/2018
-
5. Punching of reinforced concrete flat slabs with holes and shear reinforcement
Abstract Punching shear is a possible type of failure that occurs in reinforced concrete flat slabs, which can develop with an ultimate load below flexural capacity. Several researchers have studied the punching resistance of flat slabs over recent years. Although they have made great advances, there are codes that show different approaches to a singular des
REM, Int. Eng. J.. Publicado em: 2017-12
-
6. Effect of CFRP and TRM Strengthening of RC Slabs on Punching Shear Strength
Abstract The paper presents experiments involving punching of RC slabs strengthened using externally bonded carbon fiber reinforced polymer (CFRP) sheet and textile reinforced mortar (TRM). Twelve RC slab specimens of two concrete grades (39.9 and 63.2 MPa) and employing two strengthening schemes (CFRP and TRM) were tested. Specimens were supported on two op
Lat. Am. j. solids struct.. Publicado em: 2015-09
-
7. Punção em lajes lisas de concreto armado com furo adjacente ao pilar e transferência de momento / Punching Shear In Reinforced Flat Slabs with Hole Adjacent to the Column and Moment Transfer
São investigados o comportamento estrutural e a resistência última à punção de ligações laje-pilar de regiões internas das lajes lisas, com um furo adjacente ao pilar, e com ou sem transferência de momento fletor da laje ao pilar. As principais variáveis foram: a existência ou não de furo, a taxa e a distribuição da armadura de flexão, a dire
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 17/06/2011
-
8. Punção em lajes lisas de concreto armado com furo adjacente ao pilar e transferência de momento / Punching Shear In Reinforced Flat Slabs with Hole Adjacent to the Column and Moment Transfer
São investigados o comportamento estrutural e a resistência última à punção de ligações laje-pilar de regiões internas das lajes lisas, com um furo adjacente ao pilar, e com ou sem transferência de momento fletor da laje ao pilar. As principais variáveis foram: a existência ou não de furo, a taxa e a distribuição da armadura de flexão, a dire
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 17/06/2011
-
9. Plastic deformation analysis of low-carbon steel due to metal hole punching using coated and uncoated tools
This paper presents subsurface hardening results of the low-carbon steel plate, deformed under industrial test conditions by punches manufactured in quenched and tempered AISI D2 steel, with and without TiN coating. The punches are 12º double shear angle shaped. A longer tool life was obtained in tools with TiN coatings applied by Physical Vapor Deposition
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-03
-
10. Análise crítica dos critérios normativos de dimensionamento à punção em lajes lisas
The Brazilian code NBR 6118/2003 introduces significant changes in the criteria for the punching shear strength of reinforced and prestressed concrete flat slabs. In this scenario, the objective of this work is to evaluate these punching shear design procedures in terms of safety, precision and economy with respect to test results of reinforced and prestress
Publicado em: 2008
-
11. Punção em lajes cogumelo de concreto protendido com cabos não-aderentes na ligação laje-pilar de borda / Punção em lajes cogumelo de concreto protendido com cabos não-aderentes na ligação laje-pilar de borda / Punching shear in prestressed concrete flat slabs with slabedge column connections / Punching shear in prestressed concrete flat slabs with slabedge column connections
São investigados o comportamento estrutural e a resistência última à punção de ligações lajepilar de borda, em edifícios em lajes cogumelo de concreto protendido com cabos nãoaderentes, tendo como principal variável a excentricidade da força cortante, dada pela variação da relação M(momento transferido ao pilar) / V(força cortante). Foram en
Publicado em: 2008
-
12. Estudo de nós soldados tipo K de treliças planas constituídas por seções tubulares circulares de aço
The trusses of circular hollow sections, should be checked about last limit states of plastification and punching shear of chord wall. The standards AWS D1.1: 2002, ANSI /IACS 360-05 and EN 1993-1-8:2005 have virtually identical procedures for the verification of these limits states, based mainly in the works of Wardenier et al. (1991) and Packer and Henders
Publicado em: 2008