Pullout Resistance
Mostrando 1-12 de 16 artigos, teses e dissertações.
-
1. INFLUENCE OF DIAMETER AND GEOMETRY IN THE TAPPING OF THE PILOT HOLE IN PEDICLE SCREWS
RESUMO Objetivo: Avaliar o torque de inserção e a força de arrancamento de cada parafuso com diferentes diâmetros e machos. Métodos: Foram utilizados no estudo blocos de poliuterano com orifício piloto de 2,7mm, sendo feito um grupo experimentais com 5 blocos sendo avaliado o torque de inserção com torquímetro e avaliado o arrancamento de cada par
Coluna/Columna. Publicado em: 2019-03
-
2. Mechanical and Durability Performance of Polyacrylonitrile Fiber Reinforced Concrete
In this paper, the impact toughness, autogenous shrinkage, chloride penetration resistance, permeability resistance and abrasion resistance performance of prepared concrete reinforced with Polyacrylonitrile fiber (PAN fiber) were researched. The PAN fiber volume concentration percentages of cement were 0, 0.5%, 1.0%, 1.5% and 2.0%, respectively. The results
Mat. Res.. Publicado em: 03/11/2015
-
3. Implementação de ensaios de arrancamento cíclico de geossintéticos / Implementation of cyclic pull out tests of geosynthetics
Os ensaios de arrancamento cíclicos são utilizados para avaliar o comportamento de sistemas de solo reforçado quando submetidos a carregamentos cíclicos, podendo ser aplicados na área de pavimentos reforçados com geossintéticos ou em comportamento sísmico de solos reforçados com geossintéticos. O comportamento de sistemas de solo reforçado submeti
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/03/2011
-
4. Resistência ao arrancamento de grampos em solo residual de gnaisse / Pullout resistance of nails in gneiss residual soil
A adoção da técnica de solo grampeado no projeto de contenção de taludes ou escavações vem sendo cada vez mais freqüente, com isto se faz necessário um maior numero de estudos sobre a estimativa da resistência ao arrancamento (qs) em função de parâmetros de ensaios de campo para os mais variados tipos de solos brasileiros. O objetivo desta pesqu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/12/2010
-
5. Influência da pressão da água intersticial na resistência ao arrancamento de geogrelha em solo coesivo / Influence of pore water pressure in pullout resistance of geogrid in cohesive soil
O bom desempenho de uma estrutura de solo reforçado depende fundamentalmente da interação entre o solo de aterro e o elemento de reforço. A utilização de solos coesivos pode causar efeitos negativos à estabilidade da estrutura. Um elevado percentual de partículas finas na composição do solo pode favorecer ao desenvolvimento de pressões da água in
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 08/12/2010
-
6. Microstructure and mechanical properties of gypsum composites reinforced with recycled cellulose pulp
The use of waste fibers for the reinforcement of brittle matrices is considered opportune for the sustainable management of urban solid residues. This paper examines the microstructure and mechanical properties of a composite material made of gypsum reinforced with cellulose fibers from discarded Kraft cement bag. Two different kinds of gypsum were used, nat
Publicado em: 2010
-
7. Microstructure and mechanical properties of gypsum composites reinforced with recycled cellulose pulp
The use of waste fibers for the reinforcement of brittle matrices is considered opportune for the sustainable management of urban solid residues. This paper examines the microstructure and mechanical properties of a composite material made of gypsum reinforced with cellulose fibers from discarded Kraft cement bag. Two different kinds of gypsum were used, nat
Materials Research. Publicado em: 2008-12
-
8. Avaliação do comportamento mecânico ao cisalhamento de conectores de barras de aço com ganchos em vigas mistas de madeira laminada colada e concreto
The main objective of this work was to propose a reference specimen for the push-out test of rod-type fasteners in timber-concrete connections. The following experimental tests have been performed in order to achieve the goals of this research: pull-out tests of bonded-in steel rods in wood specimens, pull-out tests of bonded-in steel rods in concrete specim
Publicado em: 2008
-
9. RESISTANCE OF INTERFACES SOILGEOSYNTHETICS: DEVELOPMENT OF EQUIPMENT AND TESTS / RESISTÊNCIA DE INTERFACES SOLO-GEOSSINTÉTICO: DESENVOLVIMENTO DE EQUIPAMENTO E ENSAIOS
The demand for better techniques of sizing motivated the development of studies capable to supply a larger understanding of the behavior of the geosynthetics when inserted in the soil mass. The interaction soil- geosynthetics it is complex, being function of the properties of the used materials, soil and geossintético, and expresses through the adhesion and
Publicado em: 2008
-
10. Influence of the pilot hole preparation and screw frequency insertion of the implant on the insertion torque and pulling out resistance / Influência do preparo do orifício piloto e da freqüencia de colocação do implante no seu torque de inserção e resistência ao arrancamento
The aim of the study was to evaluate the influence of the diameter of the pilot hole and the frequency of screw placement on pullout out resistance and insertion torque of the pedicle screw. Pedicle screws of 5, 6 and 7mm of the USS system for vertebral fixation were inserted into wood, polyurethane, polyethylene and bovine bone. The pilot hole for screw ins
Publicado em: 2007
-
11. Influência de parâmetros microestruturais no comportamento tribológico de ligas ferrosas multicomponentes / Influence of microstructural parameters on the tribological behavior of multicomponent ferrous alloys
The aim of this work is to evaluate the effect of microstructural parameters (eutectic carbides and matrix hardness) of multi-component ferrous alloys on tribological behavior in sliding wear and micro-abrasive wear. The samples were two series of alloys with variable vanadium (V serie) and molybdenum (M serie) contents and fixed amounts of other elements. E
Publicado em: 2007
-
12. BEHAVIOR OF GEOGRIDS IN REINFORCED SOIL WALL AND PULLOUT TESTS / COMPORTAMENTO DE GEOGRELHAS EM MURO DE SOLO REFORÇADO E EM ENSAIOS DE ARRANCAMENTO
The behavior of a 5m high and 1700m long reinforced soil wall was studied in this work. The wall constitutes the upper part of a dike constructed in Poços de Caldas-MG, Brazil, by Alcoa Aluminum S.A. to contain Bauxite residues. The wall was constructed using geogrids and a residual silty-clay. Two wall sections were instrumented. Horizontal and vertical di
Publicado em: 2006