Pre Tension
Mostrando 1-12 de 107 artigos, teses e dissertações.
-
1. Os efeitos da bandagem elástica no músculo trapézio em adultos saudáveis
RESUMO Objetivo Verificar o efeito da bandagem elástica no músculo trapézio, por meio da eletromiografia e de um questionário autorreferido em adultos saudáveis. Método Participaram 51 adultos saudáveis, de ambos os sexos, na faixa etária entre 20 e 35 anos. Os sujeitos foram divididos em três grupos: G1, que utilizou a bandagem elástica com tens
CoDAS. Publicado em: 17/10/2019
-
2. Numerical simulation of bolted connections
Abstract This article presents the modeling of a complete bolted connection based on a model with one bolt connecting two or three plates. Initially, the behavior of this model with one bolt is analyzed by comparing it with existing bibliography for 3 different types of applied load: tension, shear and a combination of these two. This model includes all nece
Lat. Am. j. solids struct.. Publicado em: 22/10/2018
-
3. Structural Behavior of RC Beams Containing a Pre- Diagonal Tension Crack
Abstract This study focuses the light on the shear behavior of pre-cracked beams, and examines the feasibility of applying fracture mechanics concepts to widen the understanding of shear behavior and mechanisms. The experimental program contains ten beam specimens of high strength concrete (HSC) and steel fiber reinforced concrete (SFRC). Pre-cracks were emb
Lat. Am. j. solids struct.. Publicado em: 16/07/2018
-
4. Fracture Behavior and Fatigue Performance of Inconel 625
Inconel 625 is a nickel-based highly-resistant superalloy widely used in aerospace components, in the nuclear industry, and especially in the maritime industry. Materials such as Inconel 625 have been widely used in oil exploration of Brazilian pre-salt layers due to their excellent resistance to corrosion under tension, pitting and crevice corrosion by chlo
Mat. Res.. Publicado em: 25/06/2018
-
5. Finite element simulation of fracture in a restored premolar tooth using high aspect ratio elements
Abstract Introduction The term cracked tooth syndrome refers to an incomplete fracture of a vital posterior tooth that involves the dentin and occasionally extends into the pulp. There is a very limited number of publications trying to model dentin crack growth using numerical techniques. Therefore, it is essential to numerically model this phenomenon in o
Res. Biomed. Eng.. Publicado em: 19/03/2018
-
6. Effects of Pre-Strain on the Evolution of Microstructure and Strain Hardening of Extruded Az31 Magnesium Alloy
Pre-compression 3% and pre-stretch 3% subsequent annealing at 200ºC for 2h are conducted on AZ31 magnesium alloys, then inverse tensile and compressive deformation are carried out at room temperature, respectively. During inverse tension 3% deformation on 1st pre-compression samples, detwinning behavior happens; after 2nd pre-compression 3%, the volume frac
Mat. Res.. Publicado em: 25/05/2017
-
7. Effect of cantilever length and alloy framework on the stress distribution in peri-implant area of cantilevered implant-supported fixed partial dentures
ABSTRACT Because many mechanical variables are present in the oral cavity, the proper load transfer between the prosthesis and the bone is important for treatment planning and for the longevity of the implant-supported fixed partial denture. Objectives To verify the stress generated on the peri-implant area of cantilevered implant-supported fixed partial d
J. Appl. Oral Sci.. Publicado em: 2016-04
-
8. An efficient analytical model to evaluate the first two local buckling modes of finite cracked plate under tension
Abstract The analytical approach is presented for both symmetric and anti-symmetric local buckling of the thin-plate in finite sizes and with a center crack under tension. An efficient classical solution based on the principle of minimum total potential energy was provided using only 2 and 1 degrees of freedom for symmetric and anti-symmetric modes and the l
Lat. Am. j. solids struct.. Publicado em: 2015-11
-
9. Mechanical Behavior of a Twip Steel (Twinning Induced Plasticity)
ABSTRACTA TWIP steel (0.65%C; 22%Mn; 0.28%Cr; 0.16%Si) was produced in the laboratory by melting, casting, hot forging and hot rolling. The relationship between mechanical twinning fraction and mechanical behavior of this steel was studied through tension tests at the following temperatures: 25, 300, 325, 350, 375 and 400°C. Fracture toughness was measured
Matéria (Rio J.). Publicado em: 2015-09
-
10. Effect of Quenching Rate and Pre-strain on the Strain Ageing Behaviors of 7075 Aluminum Alloys
The mechanical properties of aluminum alloys are strongly dependent on the thermo-mechanical process so, the strain ageing behavior of 7075 Al-alloy was investigated in this study. A set of test pieces was solution heat treated at 480 °C for 2 h, water quenched (SHTWQ) then pre-strained for 8% in tension. The test samples were aged at 140 °C for 0.5, 1, 2,
Mat. Res.. Publicado em: 2015-04
-
11. Electronic tongue system to evaluate flavor of soybean (Glycine Max (L.) Merrill) genotypes
An electronic tongue system was tested as a fast and efficient analytical tool for flavor evaluation of soybean genotypes. Grain samples of 25 soybean lines were analyzed using 0.25 g of milled samples added to 100 mL of distilled water and mixing for one minute on a magnetic stirrer. An aliquot (50 mL) from the filtered liquid was used for the analysis on a
Braz. arch. biol. technol.. Publicado em: 2014-10
-
12. Effects of preoperative irradiation using fractioned electron beam on the healing process of colocolonic anastomosis in rats undergoing early and late surgical intervention
PURPOSE: To investigate the effects of preoperative fractioned irradiation using an electron beam on the healing process of colocolonic anastomoses in rats that underwent early and late surgical intervention. METHODS: Thirty Wistar rats, distributed as follows: group A (surgery only), group B (fractionated irradiation for 30 days (if), surgery seven days aft
Acta Cir. Bras.. Publicado em: 2013-01