Polymethylmethacrylate Pmma
Mostrando 1-12 de 23 artigos, teses e dissertações.
-
1. Biomechanical Test after Hip Cannulated Screw Removal (in vitro Analysis)
Resumo Objetivo Avaliar, pormeio de ensaio biomecânico, a resistência e a energia necessária para ocorrência de fratura do fêmur proximal em osso sintético após retirada de parafusos canulados em forma de triângulo invertido e comparar os resultados obtidos com técnica de reforço utilizando polimetilmetacrilato (PMMA). Métodos Foramutilizados
Rev. bras. ortop.. Publicado em: 07/10/2019
-
2. Photoluminescence of Solvent-Selected Fluorescent Moieties in MEH-PPV Solutions and Films
In this work, we examined how photoluminescence in poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) is affected by morphology, dictated by the mode of preparation. For that, MEH-PPV dilute solutions in good and non-solvents, thick cast films with poly[methylmethacrylate] (PMMA) as inert matrix and spin-coated thin films were prepared. Thes
J. Braz. Chem. Soc.. Publicado em: 2018-03
-
3. Tensile Bond Strength of a Soft Liner to an Acrylic Resin after Primer Application and Thermocycling
Purpose: The aim of this study was to evaluate the effect of a surface treatment with Sofreliner primer on tensile bond strength of a resin-based soft liner (Coe-Soft) bonded to a polymethylmethacrylate (PMMA) resin before and after accelerated aging simulated by a thermocycling machine. Material and Methods: One hundred and twenty rectangular specimens of
Mat. Res.. Publicado em: 04/12/2015
-
4. Influence of substratum position and acquired pellicle on Candida albicans biofilm
The purpose of this study was to evaluate the influence of the substratum position and the saliva acquired pellicle (AP) on Candida albicans biofilm development. Poly(methylmethacrylate) (PMMA) disks were fabricated and randomly allocated to experimental groups: HNP (disks placed in a horizontal position and uncoated by pellicle), VNP (disks placed in a vert
Braz. oral res.. Publicado em: 11/06/2013
-
5. Effect of plasma fluorination variables on the deposition and growth of partially fluorinated polymer over PMMA films
In this work, an investigation was made of the modification of film surface of Poly(methylmethacrylate) (PMMA) using the plasma polymerization technique. PMMA films 10 µm thick were obtained by Spin-Coating starting from a chloroform solution (15.36% w/w). The films were exposed to the plasma of CHF3 at different gas pressures and exposure times to increase
Polímeros. Publicado em: 2013
-
6. Nitroxide mediated and atom transfer radical graft polymerization of atactic polymers onto syndiotactic polystyrene
'Living' radical graft polymerization was employed to prepare graft copolymers with nitroxide-mediated arylated syndiotactic polystyrene as the backbone and polystyrene (PS), poly(p-methylstyrene) (PMS) and poly(methylmethacrylate) (PMMA) as branches. A two-stage process has been developed to synthesize the macroinitiator. First, syndiotactic polystyrene (sP
Brazilian Journal of Chemical Engineering. Publicado em: 2012-06
-
7. Reconstruction of bony facial contour deficiencies with polymethylmethacrylate implants: case report
Facial trauma can be considered one of the most serious aggressions found in the medical centers due to the emotional consequences and the possibility of deformity. In craniofacial surgery, the use of autologous bone is still the first choice for reconstructing bony defects or irregularities. When there is a shortage of donor bone or a patient refuses an int
J. Appl. Oral Sci.. Publicado em: 2011-08
-
8. Effect of additives on the compressive strength and setting time of a Portland cement
Improvements in strength and setting time of Portland cements (PC) are needed to enhance their performance as endodontic and load bearing materials. This study sought to enhance the compressive strength and setting time of a PC by adding one of the following additives: 20% and 30% poly-methylmethacrylate (PMMA), 20% and 30% irregular and spherical amalgam al
Brazilian Oral Research. Publicado em: 2010-06
-
9. Moldagem por injeção de microcomponentes ópticos poliméricos gerados em insertos usinados por torneamento de ultraprecisão / Injection molding of polymer micro-optical components generated in inserts by ultra-precision turning
Este trabalho analisou o processo de moldagem por injeção de micro elementos ópticos difrativos usinados em insertos de cobre eletrolítico com ferramenta de diamante com ponta única. Quatro tipos de microestruturas características foram selecionados neste estudo, a saber: lente anesférica, lente de Fresnel, grade de difração (blaze grating) e sensor
Publicado em: 2010
-
10. Estudo da reação tecidual à administração intraperitoneal de polimetilmetacrilato (PMMA) em ratos da linhagem Wistar
This experimental study aims to analyze the responses and tissue migration of Polymethylmetacrylate (PMMA) after implantation in the peritoneal cavity of rats. Methods: We used 80 male Wistar rats, adult, weighing between two hundred and ninety-four hundred grams, distributed in randomly in 4 groups: Group in which it was administered 0.4 ml of 0.9% saline S
Publicado em: 2009
-
11. Development of luminescent systems based on PHB and PMMA polymers doped with rare earth complexes / Desenvolvimento de sistemas luminescentes à base dos polímeros PHB e PMMA dopados com complexos de terras raras
This work presents the preparation, characterization and studies of photoluminescence properties based on trivalent rare earth coordination complexes of βdiketonates and salicylates (β-diketonates = acac- and tta-; salicylates = Hsal- and RE3+ = Sm3+, Eu3+, Gd3+ and Tb3+) doped into polymers PHB (poly3hydroxybutyrate) and PMMA (polymethylmethacryla
Publicado em: 2009
-
12. Study of the influence of synthesis conditions on the size particles of polystyrene and poly(methylmethacrylate) with lanthanide complexes / Estudo da influÃncia das condiÃÃes de sÃntese no tamanho de partÃcula de lÃtices de poliestireno e poli(metilmetacrilato) e incorporaÃÃo de complexos de lantanÃdeos
A polimerizaÃÃo em emulsÃo à um processo utilizado na produÃÃo de lÃtex sintÃticos. A tÃcnica à muito utilizada, pois permite a produÃÃo de grande variedade de polÃmeros, permitindo o controle das propriedades fÃsico-quÃmicas e morfolÃgicas do lÃtex. A concentraÃÃo do monÃmero, iniciador, fluxo de nitrogÃnio, velocidade de agitaÃÃo e a
Publicado em: 2008