Polymer Sbs
Mostrando 1-12 de 17 artigos, teses e dissertações.
-
1. Composites based on low-density polyethylene combined with PETcoated SBS paperboard shavings
ABSTRACT In this study, polymer composites comprised of shavings of SBS paperboard coated with polyethylene terephthalate (PET) and recycled low-density polyethylene (LDPE) were obtained. The tensile properties, flexural strength, impact resistance and water absorption were determined according to the standards published by the American Society for Testing a
Matéria (Rio J.). Publicado em: 06/12/2018
-
2. Production of fibrous polymer scaffolds for tissue engineering using an automated solution blow spinning system
Abstract Introduction Solution blow spinning (SBS) and airbrushing are two techniques that can be used as alternatives to electrospinning in the production of fibrous scaffolds for tissue engineering (TE). SBS seems particularly interesting due to its versatility, however, it has not been much explored and no automated SBS systems were found in the literat
Res. Biomed. Eng.. Publicado em: 22/10/2018
-
3. Influence of SEBS-MA and SBS compatibilizers on properties and morphology of blends of polystyrene/rubber residue (SBRr) from the footwear industry
Abstract The reuse of rubber waste is very important today, both to reduce the harmful effects on the environment, and to reduce the cost of new material development. Considering that most of the studies reported in literature refer to the reuse of tire waste, this article aims to evaluate the influence of styrene-butadiene-styrene (SBS) and styrene-(ethylen
REM, Int. Eng. J.. Publicado em: 2017-06
-
4. Bonding of the Polymer Polyetheretherketone (PEEK) to Human Dentin: Effect of Surface Treatments
Resumo O poli-éter-éter-cetona (PEEK) é um material indicado para as estruturas de próteses parciais fixas. O efeito de diferentes tratamentos de superfície na resistência de união entre PEEK e dentina humana foi avaliado. Cem cilindros de PEEK (3 mm×3 mm) foram divididos em cinco grupos de acordo com tratamento de superfície: silicatização, jatea
Braz. Dent. J.. Publicado em: 2016-12
-
5. Viscoelastic Behaviour Characterization of a Gap-graded Asphalt Mixture with SBS Polymer Modified Bitumen
A characterization of the linear thermo-viscoelastic behaviour of a gap-graded bituminous mixture with SBS-polymer modified bitumen and RAP aggregates is presented in this paper. A comparison was made, in terms of their viscoelastic behaviour, between this innovative mixture and two commonly used well-graded base-course French mixtures made with pure bitumen
Mat. Res.. Publicado em: 2015-04
-
6. The use of thermoplastic rubber type styrene-butadiene-styrene asphalt cements oil / O emprego de borracha termoplástica tipo estireno-butadieno-estireno em cimentos asfálticos de petróleo
Este trabalho apresenta resultados o estudo de pesquisa e desenvolvimento de misturas de polímeros em cimento asfáltico de petróleo. O asfalto é um excelente material aglutinante utilizado na construção de rodovias e vias urbanas, entretanto o aumento do número de veículos comerciais e da carga transportada por eixo tem levado a deteriorização prem
Publicado em: 2010
-
7. Efeitos de aditivo tipo óleo e enxofre na reologia de asfaltos modificados com SBS
O uso de asfaltos modificados com polímeros tem crescido significativamente nas últimas décadas em função do aumento da densidade de tráfego, da carga por eixo nos veículos e da pressão dos pneus. Estes ligantes proporcionam o aumento a vida útil e a redução do custo de manutenção das rodovias. Os polímeros mais utilizados na modificação de a
Publicado em: 2010
-
8. Estudo da tenacificação do poliestireno com elastômeros butadiênicos / Polystyrene toughening by butadiene elastomers
This Dissertation describes a study about the toughening of polystyrene with different types of polybutadiene (high-cis, low-cis and styrene - butadiene diblock or triblock copolymers). These materials (High Impact of PolyStyrene HIPS) were performed by melt blending. The mechanical properties (hardness, tensile strength and impact strength); morphology and
Publicado em: 2009
-
9. Properties of SBS and sisal fiber composites: ecological material for shoe manufacturing
The worldwide trend toward using cheap, atoxic and durable materials from renewable resources contributes to sustainable development. Thus, the investigation of the potential use of vegetal fibers as reinforcing agent in polymeric composites has gained new significance. Sisal fiber has emerged as a reinforcing material for polymers used in automobile, footwe
Materials Research. Publicado em: 2008-12
-
10. Rheological evaluation of polymer-modified asphalt binders
Currently, the most used polymer for asphalt binder modification is the thermoplastic elastomer styrene butadiene styrene (SBS) and aromatic oil is commonly added to the mixtures to improve their compatibly. This paper proposes the use of oil shale from sedimentary rock as a compatibilizer agent for polymer-modified asphalt binder (PMB). PMBs were produced b
Materials Research. Publicado em: 2008-09
-
11. Asfalto modificado com polimero SBS para pavimentos drenantes / Asphalt modified with polymer SBS for drain pavements
The polymer SBS - Styrene-Butadiene-Styrene has been very employed to modify the asphalt, for paving and for industrial applications. In that research the study of the asphalt was approached modified with polymer SBS, presenting better behavior than I asphalt conventional, being shown as the polymeric behaves when being mixed with the asphalt and which chara
Publicado em: 2007
-
12. Evaluation of asphalt mixtures produced with conventional peruvian asphalt binder PEN 60/70 and SBS polymer-modified type I 60/60 and PG 76-22 / Avaliação de misturas produzidas com ligantes asfálticos peruanos convencional PEN 60/70 e modificados por polímero SBS tipo I 60/60 e PG 76-22
The main goal of this work is the evaluation of the behavior of conventional peruvian asphalt binder AC PEN 60/70 and SBS polymer-modified asphalts I 60/60 and PG 76-22, when used in hot-mix asphalt (HMA), under both conditions with and without short-term aging. It aims also to establish the asphalt binder performance grade (PG), which is based on the weathe
Publicado em: 2007