Piezoelectricity
Mostrando 1-12 de 20 artigos, teses e dissertações.
-
1. Hygro-thermo-mechanical bending of FG piezoelectric plates using quasi-3D shear and normal deformations theory
Abstract A simple quasi-3D sinusoidal shear and normal deformations theory for the hygro-thermo-mechanical bending of functionally graded piezoelectric (FGP) plate is developed under simply-supported edge conditions. The governing equations are deduced based on the principle of virtual work. The exact solutions for FGP plate are obtained. The current study i
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
2. Piezoelectricity from Elastic and Dielectric Measurements on Unpoled Ferroelectrics
A method is described to assess the piezoelectric response of ferroelectric materials from the temperature dependence of the elastic moduli and dielectric constant of unpoled samples. The limits and advantages over the traditional methods on poled samples are discussed. A quantitative check is made by comparing the piezoelectric softening measured below the
Mat. Res.. Publicado em: 07/06/2018
-
3. Complete Band Gaps in Nano-Piezoelectric Phononic Crystals
We study the band structure of elastic waves propagating in a nano-piezoelectric phononic crystal consisting of a polymeric matrix reinforced by BaTiO3 inclusions in square, rectangular, triangular, honeycomb and Kagomé lattices. We also investigate the influence of inclusion cross section geometry - circular, hollow circular, square and rotated square with
Mat. Res.. Publicado em: 30/10/2017
-
4. Theoretical investigations of the bulk modulus in the tetra-cubic transition of PbTiO3 material
Resulting from ion displacement in a solid under pressure, piezoelectricity is an electrical polarization that can be observed in perovskite-type electronic ceramics, such as PbTiO3, which present cubic and tetragonal symmetries at different pressures. The transition between these crystalline phases is determined theoretically through the bulk modulus from t
Quím. Nova. Publicado em: 2014
-
5. Análise do comportamento eletroaeroelástico de uma seção típica para geração piezelétrica de energia / Electroaeroelastic behavior analysis of a typical section for piezoelectric energy harvesting
Converting aeroelastic vibrations into electricity for low power generation has received growing attention over the past few years. In addition to potential applications for aerospace structures, the goal is to develop alternative and scalable configurations for wind energy harvesting to use in wireless electronic systems. The use of a typical airfoil sectio
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/02/2012
-
6. Modelagem e análise de uma asa piezoaeroelástica para geração de energia / Modeling and analysis of a piezoaeroelastic wing for power generation
A redução do consumo de energia dos sistemas eletrônicos, fez com que a pesquisa de novas fontes de energia para alimentar estes dispositivos tivesse enorme importância na última década. Algumas destas fontes são provenientes da conversão de energia de vibrações mecânicas em energia elétrica. Veículos aéreos não tripulados (UAVs) e micro veíc
Publicado em: 2010
-
7. Modelo em elementos finitos para simulação de geradores piezelétricos de energia / Finite element modeling of a piezoelectric energy harvester
A conversão de energia de vibração disponível no ambiente em energia elétrica tem sido investigada por diversos pesquisadores nos últimos anos. O objetivo é alimentar sistemas de baixo consumo convertendo energia mecânica disponível no ambiente em energia elétrica. A literatura recente mostra que a transdução piezelétrica tem recebido a maior at
Publicado em: 2010
-
8. Estudo de materiais piezoelétricos da família III-V obtidos por sputtering reativo visando sua aplicação em sensores e MEMS. / Study of III-V piezoelectric materials obtained by reactive sputtering for sensors and MEMS applications.
Neste trabalho, apresento um estudo sobre a fabricação e caracterização físico-química de filmes finos de nitreto de alumínio (AlN) obtidos pela técnica de pulverização catódica reativa por rádio frequência (r.f sputtering) utilizando um alvo de alumínio puro. Visto que o AlN é um material que apresenta piezoeletricidade e compatibilidade com
Publicado em: 2010
-
9. Modelagem e controle ativo de vibrações de painéis flexíveis de satélites artificiais empregando transdutores piezelétricos / Modeling and Active Vibration Control of Flexible Panels of Artificial Satelites Using Piezoelectric Transducers
Neste trabalho foram desenvolvidos procedimentos de modelagem do comportamento dinâmico de satélites artificiais contendo painéis flexíveis, objetivando o controle de vibrações destes painéis através da ação combinada de uma roda de reação e de atuadores piezelétricos colados às suas superfícies. São primeiramente apresentados alguns elemento
Publicado em: 2009
-
10. LINEAR ULTRASONIC MOTOR WITH TUBULAR GEOMETRY / MOTOR ULTRA-SÔNICO LINEAR COM GEOMETRIA TUBULAR
This work presents the study on a linear ultrasonic motor with tubular geometry for linear displacements. Similar topologies, reported elsewhere, are conceived for producing rotary motions. Due to some particular characteristics of this geometry, not explored yet, a new study on interaction between resonance modes in a hollow cylinder for linear movement gen
Publicado em: 2008
-
11. Modeling and optimization of piezoelectric shunts apply to passive vibration control / Modelagem numérica e otimização de shunts piezelétricos aplicados ao controle passivo de vibrações
Due to the development of new technologies, industrial structures are now made of lighter materials and work at higher operation speeds producing an increasing vibration and noise level generation. As a result, different techniques of active and passive control have been developed and are continuously being improved. Among the passive control techniques, the
Publicado em: 2007
-
12. Termo eletretos de teflon FEP como transdutores piezelétricos / Thermo electrets of teflon FEP as piezoelectric transducers
Os termo eletretos piezelétricos de teflon FEP apresentam-se como elementos que podem competir em preço e funcionalidade com os transdutores atuais. Quando carregados impulsivamente, as folhas de teflon FEP retêm cargas elétricas superficiais por um período longo, superior a 500 anos. Excitados mecanicamente, resultam em um alto nível de sinal elétric
Publicado em: 2006