Numerical Simulations
Mostrando 13-24 de 614 artigos, teses e dissertações.
-
13. AN INVESTIGATION OF THE HEAT TRANSFER PERFORMANCE OF DUAL IMPROVED INTERMIG IMPELLERS IN A STIRRED TANK WITH AN INNER HEATING COIL
Abstract The heat transfer process in a stirred tank of diameter T=0.5m equipped with dual-layer improved Intermig impellers and helical coils was investigated by experiment and numerical simulation methods. The temperature field, the temperature boundary layer lateral to the coil and the heat transfer coefficient were measured at different rotational speeds
Braz. J. Chem. Eng.. Publicado em: 09/12/2019
-
14. Hardening and Dynamic Recovery During Hot Compression Test of Copper Simulated as Viscoplastic Material
The Norton-Bailey equation was used to simulate by finite elements the hardening and dynamic recovery of copper during the hot compression tests. The constants of Norton-Bailey equation were determined from the Voce-Kocks model. The simulation assumes a Mortar Contact with Coulomb friction and axial symmetry. Numerical results were compared with experiments.
Mat. Res.. Publicado em: 05/12/2019
-
15. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
16. Structural models for analysis of reinforced concrete frame buildings with masonry infills
Resumo Este trabalho tem como objetivo o estudo do comportamento de pórticos de edifícios de concreto armado preenchidos com alvenaria frente às ações horizontais, empregando-se dois modelos estruturais: i) modelo de diagonal equivalente (MDE) e ii) modelo com elementos finitos bidimensionais para estado plano de tensões (MEF). No primeiro modelo, a al
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
17. Numerical study of upstream disturbances on the performance of electromagnetic and ultrasonic flowmeters
ABSTRACT Electromagnetic and ultrasonic flowmeters are high precision devices that can measure the water flow in pressurized irrigation networks. In these networks, the inadequate installation distance of flow control valves generates upstream disturbances which will increase measurement errors and reduce the accuracy of the equipment. Therefore, estimating
Sci. agric. (Piracicaba, Braz.). Publicado em: 04/11/2019
-
18. Interplay between Near-Field Properties and Au Nanorod Cluster Structure: Extending Hot Spots for Surface-Enhanced Raman Scattering
Materials science has observed a continuous increase in the use of metal nanoparticles in a wide range of studies, from fundamental physics to technological applications such as photocatalysis and optical communication devices. This broad scope has the same fundamental origin, the localized surface plasmons, whose excitation leads to strong light confinement
J. Braz. Chem. Soc.. Publicado em: 24/10/2019
-
19. Assessing the Impact of Prophylactic Vaccines on HPV Prevalence
RESUMO Um modelo matemático á proposto para avaliar as estratégias de controle da transmissão do HPV na população humana (homens e mulheres). O número reprodutivo básico da doença, R 0, é dado pela média geométrica do número reprodutivo básico obtido nas populações femininas e masculinas. O modelo tem um equilíbrio livre da doença globalmen
TEMA (São Carlos). Publicado em: 16/09/2019
-
20. Effects of soil-structure interaction in seismic analysis of buildings with multiple pressurized tuned liquid column dampers
Abstract In this paper soil-structure interaction (SSI) effects are investigated while an array of Pressurized Tuned Liquid Column Dampers (PTLCD) is employed for seismic vibration control of buildings. This device represents the most general case of a passive damper, with different reduction options to other control devices obtained by simplifying the invol
Lat. Am. j. solids struct.. Publicado em: 12/09/2019
-
21. Numerical Simulation of Atom-Transfer Radical Polymerization of tert-butyl Methacrylate
Block copolymers based on tert-butyl methacrylate (tBMA) have many uses, such as thermo‐responsive polymers, amphiphilic copolymers, and many applications in the medical field. Atom-transfer radical polymerization (ATRP) is the main technique to produce these controlled macromolecular architectures. This paper provides a simplified kinetic modeling and com
Mat. Res.. Publicado em: 02/09/2019
-
22. Beam-Column Joints Reinforcement Detailing Adequacy in Case of a Corner Column Loss-Numerical Analysis
Abstract This study investigates the behavior of reinforced concrete (RC) beam-column joints at the corner panel after a ground corner column loss scenario. The ductility of a frame is dependent on the ductility of its components, particularly its joints. Deficiency in joints performance can be related to an unexpected event. For example, the removal of a gr
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
23. Modular modeling approach for FDM printed structures and piezo disks for metamaterial design
Abstract Research in metamaterials has recently gained interest in the field of noise and vibration control. The ability of creating band gap zones with minimum added mass is the main feature behind its success. In addition, the use of 3D printed parts, particularly the Fused Deposition Modeling (FDM), offers a practical solution for manufacturing parts with
Lat. Am. j. solids struct.. Publicado em: 12/08/2019
-
24. A methodology to investigate the influence of the fillet radius on the buckling of integrally stiffened panels
Abstract The use of integrally stiffened panels (ISP's) in wings of small and medium-sized aircraft is frequent in aviation. These thin-walled structures are often subjected to compressive loads during their life-time and, although the finite element method has become an important tool for engineers to obtain the buckling load of structural members, some res
Lat. Am. j. solids struct.. Publicado em: 22/07/2019