Microstructures
Mostrando 13-24 de 292 artigos, teses e dissertações.
-
13. Effect of Nitrogen Addition to Shielding Gas on Cooling Rates and in the Microstructure of Thin Sheets of Duplex Stainless Steel Welded by Pulsed Gas Tungsten Arc Welding Process
The effect of the nitrogen content in the shielding gas and its effect on temperature distributions at the welded zone of thin sheets of duplex stainless steel have been evaluated. The duplex stainless steels have many features due to unique microstructural combination of austenite and ferrite grains. The phase balance can be easily shifted depending on the
Mat. Res.. Publicado em: 26/08/2019
-
14. Microstructural Adjustments and Tensile Properties of a Hot-Forged Ti−22Al−23Nb−3V−Y Alloy
Microstructures and tensile properties of a hot forged Ti−22Al−23Nb−3V−Y alloy were investigated systematically. Different heat treatments were performed to adjust the wrought microstructure to optimize tensile properties. It was found that features of O phase precipitates and its volume fraction was rather sensitive to the cooling rate after the sol
Mat. Res.. Publicado em: 19/08/2019
-
15. Glycerol Effect on the Corrosion Resistance and Electrodeposition Conditions in a Zinc Electroplating Process
Zinc electrodeposition is an economical process of Zn coating compared to conventional galvanic process. The galvanizing process is used in various industrial sectors to protect ferrous alloys during the corrosion process. In buildings, the galvanizing process is widely used to coat mortar protective screens. The electrodeposition of zinc has a relatively lo
Mat. Res.. Publicado em: 19/08/2019
-
16. Effect Of The Application Of Constant And Variable Temperatures at the Overaging Stage in the Mechanical Properties of Trip780 Steel
The effect of the application of constant temperatures (isothermal plateau) and variables (cooling ramp) during the overaging (OA) stage of the continuous annealing cycle in the microstructural characteristics and mechanical properties of a TRIP steel of the class of 780 MPa was investigated. It was simulated six overaging conditions in the equipment Gleeble
Mat. Res.. Publicado em: 15/07/2019
-
17. Effect of Annealing Process on the Microstructures and Mechanical Properties of AZ31B/A356 Composite Plate Fabricated by Cast Rolling
The effect of annealing process on the microstructures and mechanical properties of Mg/Al composite plates fabricated by cast-rolling was investigated in this study. The results show that the interfacial transition zone can be divided into three regions: a Mg transition region, an Al transition region, and an intermediate region, respectively. The microhardn
Mat. Res.. Publicado em: 10/07/2019
-
18. Double Identification of the Optimal Hot Deformation Parameter Windows for AlCu4SiMg Alloy
In order to achieve hot processing products with expected microstructures, the construction of corresponding relationships between micro-evolution mechanisms and hot processing parameters is essential. In this study, such corresponding relationships of as-cast AlCu4SiMg alloy were constructed by double evaluating processing maps and Zener-Holloman (Z) parame
Mat. Res.. Publicado em: 10/07/2019
-
19. PM versus IM Ti-5Al-5V-5Mo-3Cr Alloy in Mechanical Properties and Fracture Behaviour
The comparisons of mechanical properties and fracture behaviour between as-consolidated PM Ti-5553 alloy and as-cast IM Ti-5553 alloy were investigated through tensile, fracture toughness and impact toughness tests in this research. The slightly higher strength but much higher ductility and toughness can be identified in IM alloy specimens, which is also con
Mat. Res.. Publicado em: 27/06/2019
-
20. Generalizing Ellipsoidal Growth
This paper generalizes previous work of Rios and Villa on spherical growth. The generalized equation applies to nucleation of ellipsoids according to an inhomogeneous Poisson point process. Microstructural evolution in three dimensions of nucleation and growth transformations of ellipsoids is simulated using the causal cone method. In the simulation, nuclei
Mat. Res.. Publicado em: 13/06/2019
-
21. Effect of the Chemical Homogeneity of a Quenched and Tempered C-Mn Steel Pipe on the Mechanical Properties and Phase Transformations
Seamless steel pipes for application in the oil and gas industries are manufactured from quenched and tempered steel. Aiming to meet the required characteristics, it is necessary that the microstructure and the mechanical properties are homogeneous along the wall thickness of the pipes, which is even more critical for thick wall pipes. Considering the seamle
Mat. Res.. Publicado em: 03/06/2019
-
22. Tensile Armor Wires Submitted to Slow Strain Rate Tests in a Corrosive Environment and Cathodic Protection: a Comparison Between Two Different Microstructures
Tensile armor in flexible pipes consists of two or more layers of steel wires. Damage to the outer sheath may cause ingress of seawater in the annular space and thus corrosion of the armor wires. This work focused on the susceptibility of these wires to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) using a slow strain rate test (SSRT) under
Mat. Res.. Publicado em: 06/05/2019
-
23. Microstructure and Wear Resistance of ZrC-ZrB2 /Ni Composite Coatings Prepared by Plasma Transferred Arc Cladding
The ZrC-ZrB2/Ni metal matrix composite coatings were in-situ synthesized from a mixture of Ni, Zr and B4C by plasma transferred arc (PTA) cladding process. Microstructures and phase constituents of the coatings were characterized by electron probe micro-analyzer (EPMA) and X-ray diffraction (XRD). Microhardness and wear resistance of the coatings were system
Mat. Res.. Publicado em: 06/05/2019
-
24. Crystallization Behavior and Mechanical Properties of Cu-based Bulk Metallic Glass Composites
This work highlights the relationship between the preparation, crystallization behavior, microstructures, and mechanical properties of Cu-based bulk metallic glasses (BMGs) and their composites (BMGCs). (Cu47Zr45Al8)97.5Y1.5Nb in-situ BMGCs were prepared using isothermal annealing, and the experimental results indicate tunable mechanical properties of the al
Mat. Res.. Publicado em: 06/05/2019