Microscopy Polarization
Mostrando 1-12 de 175 artigos, teses e dissertações.
-
1. Aqueous Extract of Cumaru (Dipteryx odorata) Seeds as Corrosion Inhibitor for Mild Steel in Hydrochloric Acid Solution
The corrosion inhibition of mild steel by aqueous extract of cumaru (Dipteryx odorata) seeds and its high molecular weight fraction (HMWF) was investigated in 1 mol L-1 HCl solution. The study was carried out through gravimetric essays, open circuit potential measurements, anodic and cathodic polarization curves and electrochemical impedance analyses, as wel
J. Braz. Chem. Soc.. Publicado em: 2021-02
-
2. Changes within the care of hematopoietic cell transplantation patients after the shift of a Mexican institution to a COVID-19-only center
A new methodology using gas-diffusion microextraction (GDME) was developed for the analysis of volatile corrosion inhibitors (VCIs). The evaluation of the inhibition efficiency and corrosion rate (ν) was performed by NaCl deliquescence tests and correlated with measurements of polarization resistance (Rp) obtained from electrochemical impedance spectroscopy
Hematol., Transfus. Cell Ther.. Publicado em: 2020-10
-
3. Corrosion Protection of Steel by Volatile Corrosion Inhibitors: Vapor Analysis by Gas-Diffusion Microextraction and Mass Loss and Electrochemical Impedance in NaCl Deliquescence Tests
A new methodology using gas-diffusion microextraction (GDME) was developed for the analysis of volatile corrosion inhibitors (VCIs). The evaluation of the inhibition efficiency and corrosion rate (ν) was performed by NaCl deliquescence tests and correlated with measurements of polarization resistance (Rp) obtained from electrochemical impedance spectroscopy
J. Braz. Chem. Soc.. Publicado em: 2020-10
-
4. Aqueous Extracts of the Castor Beans as a Corrosion Inhibitor of Mild Steel in HCl Media
The present work studied aqueous extracts of castor beans as a natural inhibitor of the corrosion of mild steel in 1 M HCl using gravimetric tests, potentiodynamic polarization curves, linear polarization method, electrochemical impedance measurements, surface analysis by scanning electron microscopy (SEM) and chemical characterization by Fourier transform i
J. Braz. Chem. Soc.. Publicado em: 2020-06
-
5. Effect of Etching Temperature on Surface Properties of Ti6Al4V Alloy for Use in Biomedical Applications
The objective of this study is to evaluate the surface physicochemical properties of Ti6Al4V alloy after etching with a piranha’s solution at temperatures of 25 °C, 40 °C, and 60 °C for 30 min. Scanning electron microscopy with energy-dispersive X-ray spectroscopy, optical profilometry, X-ray diffraction, and wettability analyses were used to characteri
Mat. Res.. Publicado em: 10/01/2020
-
6. Investigation of Physicochemical Characteristics of Heavy, Medium and Blend Crude Petroleum on Corrosion Resistance of AISI 1020 Carbon Steel
This work investigates the influence of the physicochemical characteristics of heavy (17.5 °API), medium (28.3 °API) and blend (50% heavy + 50% medium) crude petroleum on corrosion of AISI 1020 carbon steel at 25.0 ± 1.0°C. The corrosion resistance of steel was analyzed by electrochemical impedance spectroscopy, potentiodynamic polarization, and scanning
Mat. Res.. Publicado em: 05/12/2019
-
7. Corrosion Resistance of TiO2-ZrO2 Nanocomposite Thin Films Spin Coated on AISI 304 Stainless Steel in 3.5 wt. % NaCl Solution
Utilizing high chromium and nickel content in AISI 304 steel confers its good corrosion resistance. However, the high content of chromium and nickel increases the steel susceptibility to corrosion caused by the high concentration of chlorine. Consequently, the electrochemical and mechanical performance of the steel degrades. In this study, the effect of addi
Mat. Res.. Publicado em: 02/12/2019
-
8. Effect of Ca Content on Properties of Extruded Mg-3Zn-0.5Sr-xCa Alloys for Medical Applications
Mg-3Zn-0.5Sr-xCa(wt.%) (x=0, 0.2, 0.5) alloys were fabricated by casting and hot extrusion. X-ray diffraction (XRD) and optical microscopy observation showed that the microstructure of Mg-3Zn-0.5Sr-xCa alloys was composed of α-Mg matrix and Mg17Sr2 phase precipitated along grain boundaries. The tensile strength of the alloy increased from 255MPa to 305MPa w
Mat. Res.. Publicado em: 30/09/2019
-
9. Corrosion Behavior of 316L and Alloy 182 Dissimilar Weld Joint with Post-Weld Heat Treatment
ABSTRACT Austenitic stainless steel and nickel-base alloys welds are widely used in nuclear reactor components, plants of energy generation, chemical, and petrochemical industries, due to their high corrosion resistance. The post weld heat treatments (PWHT) are generally applied to welding in order to relieve the welding residual stress. The aim of this work
Matéria (Rio J.). Publicado em: 16/09/2019
-
10. Produção e caracterização de revestimentos de ligas metálicas Cu-Sn em banho eletrolítico contendo glicina: ensaios preliminares
RESUMO Os problemas relacionados à corrosão são frequentes, podendo ocorrer nas mais variadas áreas, tais como, nas indústrias química, petroquímica, naval, de construção civil e automobilística, dentre outros setores produtivos. Portanto, métodos para prevenir a corrosão devem ser empregados para evitar a perda de materiais e o uso de revestimen
Matéria (Rio J.). Publicado em: 16/09/2019
-
11. Electrochemical Behavior During the Zirconium Conversion Coating Formation on AISI 1006 Steel
This study investigated a conversion coating based on hexafluorozirconic acid solution on cold-rolled (AISI 1006) steel sheets, in situ, at different pH values and immersion times. Electrochemical characterization was carried out by electrochemical impedance spectroscopy (EIS) with hexafluorozirconic acid bath as the electrolyte. Laser scanning confocal micr
Mat. Res.. Publicado em: 12/09/2019
-
12. Effect of Warm Rolling on the Corrosion and Mechanical Properties of UNS S32205 Duplex Stainless Steel
Duplex stainless steel (DSS) has been considered as an excellent alternative for applications where high corrosion resistance and high mechanical strength are required. Therefore, microstructure and properties of DSS remain topics of much interest. For this purpose, the effect of warm-rolling was studied in a duplex stainless steel. The focus of this work wa
Mat. Res.. Publicado em: 02/09/2019