Metallurgy
Mostrando 25-36 de 159 artigos, teses e dissertações.
-
25. Study of the microstructure and mechanical properties of beta tricalcium phosphate-based composites with alumina addition produced by powder metallurgy
Abstract The use of alumina as a reinforcement in metallic and ceramic matrix is well-known. The purpose of this study was to investigate the effect of alumina addition according to its amount on the microstructural and mechanical behavior of tricalcium phosphate ceramic (TCP), more specifically the β-TCP. Although β-TCP has excellent bioactive and biocomp
REM, Int. Eng. J.. Publicado em: 2017-12
-
26. Study of the AISI 52100 Steel Reuse Through the Powder Metallurgy Route Using High Energy Ball Milling
The AISI 52100 is a tool steel used in industry to produce bearings. After the end of its life cycle, it is remelted or discarded in deposits. The powder metallurgy rises as an alternative to recycle this material without any waste. The steps used to produce the AISI 52100 steel by powder metallurgy included: Machining with speed of 45 rpm, high energy ball
Mat. Res.. Publicado em: 06/11/2017
-
27. Effect of Boride Layer on PM HSS AISI M2 on the Mechanisms Acting in the Transverse Rupture Strength Test
Herein, it was conducted a study in order to examine the main fracture characteristics in the transverse rupture strength test (TRS) of a high speed steel (HSS) AISI M2 produced by powder metallurgy (PM) and with boriding treatment. Four conditions have been studied: as-sintered, borided, normalized and borided + TiN. The TRS tests were conducted in accordan
Mat. Res.. Publicado em: 06/11/2017
-
28. Structural and Magnetic Properties of Duplex Stainless steel (UNS S31803) Powders Obtained by high Energy Milling of Chips with Additions of NbC
In this study, the high energy mechanical milling was utilized to the production of duplex stainless steel powders from the recycling chips with and without the addition niobium carbide. The effect of milling time and addition carbide on the morphology, particle size and magnetic properties of the powders was investigated. The utilization of the powder metal
Mat. Res.. Publicado em: 30/10/2017
-
29. Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel
Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we inv
Mat. Res.. Publicado em: 21/08/2017
-
30. Analyzing the compressive behavior of porous Ti6Al4V by X-ray microtomography
Samples with 40% vol. of pores and a pore size distribution between 100 and 500 µm were produced by powder metallurgy from Ti6Al4V alloy powders. Sintering was performed at 1300 °C during one hour in an inert Argon atmosphere in a vertical dilatometer. The compressive strength and the porosity of these samples was investigated before and after compression
Mat. Res.. Publicado em: 21/08/2017
-
31. Influence of Tungsten on Dry Sliding Wear Behaviour of Sintered/Hot Extruded P/M Alloy Steels (Fe-C-W-Ti)
In the present scenario, Powder Metallurgy (P/M) is an established manufacturing process used to make components of complex geometries with high strength and tolerances by using incredible materials which are difficult to melt or form by other processes. The mechanical properties and microstructures will determine the component characteristic dependent on th
Mat. Res.. Publicado em: 08/06/2017
-
32. Investigation of borided layers contribution on the wear resistance and adhesion of TiN coatings
ABSTRACT The purpose of the investigation was to examine the possibility of improving tool life by reducing the wear effect and improving the adhesion of a thin film through a compound configuration that consists in boriding and PVD deposition. Single layer coatings of TiN were deposited by PVD (cathodic arc) on quenched and tempered and on borided powder me
Matéria (Rio J.). Publicado em: 02/05/2017
-
33. Effect of High Energy Milling Time of the Aluminum Bronze Alloy Obtained by Powder Metallurgy with Niobium Carbide Addition
The aluminum bronze alloy is part of a class of highly reliable materials due to high mechanical strength and corrosion resistence being used in the aerospace and shipbuilding industry. It's machined to produce parts and after its use cycle, it's discarded, but third process is considered expensive and besides not being correct for environment reasons. Thus,
Mat. Res.. Publicado em: 10/04/2017
-
34. Effect of Heating Method on Microstructure and Mechanical Properties of Zircon Reinforced Aluminum Composites
The mechanical properties and microstructure of aluminum matrix composites containing of zircon (10, 15 and 20 wt.%) as a reinforcement particles and cobalt additive (1, 1.5 and 2 wt.%) were investigated. The aluminum matrix composites were prepared by powder metallurgy technique and sintered in both conventional and microwave furnaces at temperatures higher
Mat. Res.. Publicado em: 10/11/2016
-
35. Growth and Characterization of Graphene on Polycrystalline SiC Substrate Using Heating by CO2 Laser Beam
The thermal decomposition of silicon carbide (SiC), with the subsequent formation of graphene, can be achieved by heating treatment. Several heating processes have been applied for this purpose by using SiC, either in form of powder particles or monocrystalline substrate. In this work, instead of using an expensive commercially available SiC wafer, a polycry
Mat. Res.. Publicado em: 26/09/2016
-
36. Mechanical and Microstructural Response of an Aluminum Nanocomposite Reinforced with Carbon-Based Particles
The present work deals with the study of some aluminum (Al) composites reinforced with metallized-graphite (MG) particles prepared by mechanical milling and powder metallurgy routes. Density, morphology evolution and mechanical performance of composites were investigated as a function of MG concentration and milling time. The as-milled powders were character
Mat. Res.. Publicado em: 04/08/2016