Machining Temperature
Mostrando 1-12 de 27 artigos, teses e dissertações.
-
1. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
2. Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach
Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining proc
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
3. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016
-
4. Emprego de ferramentas estatísticas para avaliação da usinabilidade de ligas de alumínio
The main objective of the present work is to study the effect of the input variables: mechanical properties of the workpiece (tensile strength, hardness and elongation) and cutting conditions (cutting speed, feed rate, depth of cut and lubri-cooling system) over the output variables: cutting forces, power consumption, cutting temperature, surface roughness (
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/05/2012
-
5. Estudo da influência da força de corte em usinagem a verde nas propriedades mecânicas de cerâmicas sinterizadas / Influence of the cutting force of green machining on the mechanical properties of sintered ceramics
The present study deals with the measurement forces of green machining ceramics and their correlation with the mechanical properties after sintering. The green machining is employed in crude compacts either to check raw formats without compromising the extreme dimensional accuracy or to obtain a preform prior to finish machining after sintering, extensively
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/01/2012
-
6. Modeling and optimization of cylindrical grinding of Al/SiC composites using genetic algorithms
The Al/SiC composites have received more commercial attention than other kinds of Metal Matrix Composites (MMCs) due to their high performance. However, a continuing problem with MMCs is that they are difficult to machine, due to the hardness and abrasive nature of the SiC particles. Grinding is often the method of choice for machining Al/SiC composites to a
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2012-03
-
7. Fresamento com ar quente: uma proposta para minimizar a formação de trincas térmicas em ferramentas de metal duro
This work presents the results, analyses and conclusions about a study carried out with objective of minimizing the thermal cracks formation on cemented carbide inserts during face milling. The main focus of investigation was based on the observation that milling process is an interrupted machining process, which imposes cyclic thermal loads to the cutting t
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2011
-
8. Finite element simulations of Ti6Al4V titanium alloy machining to assess material model parameters of the Johnson-Cook constitutive equation
The machining of titanium alloys poses several inherent difficulties owing to their unique mechanical properties and cutting characteristics. Finite element (FE) simulations have reduced the burden of extensive experimental trials in understanding the deformation behavior and optimize the cutting process. The FE code relies on the qualitative nature of input
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-06
-
9. âRevestimento por soldagem MIG/MAG empregando ligas de nÃquel para apliacaÃÃes em componentes do setor de petrÃleo e gÃs naturalâ / Gmaw Welding Overlay Of Nickel-Based Alloys For Applications In Oil And Natural Gas Components
The weld overlay of nickel-based alloys is an alternative often used in oil and gas industry to prevent corrosion in pipes and equipments operating under severe conditions. In many situations the requirements of weld overlays are based in a maximum of 5% iron content in the weld metal to ensure corrosion resistance. The aim of this study was to determine the
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 03/12/2010
-
10. Experimental and theoretical study on workpiece temperature when tapping hardened AISI H13 using different cooling systems
Tapping operations on hardened steels have always been a great challenge. Dry machining and two cooling systems were used when tapping hardened AISI H13 (53 HRC). Embedded thermocouples were used for temperature measurement close to the thread diameter in the radial and axial direction. A FEA model was used to evaluate the heat "Q", and coefficient of convec
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-06
-
11. Wear evaluation of WC inserts coated with TiN/TiAlN multinanolayers
TiN/TiAlN multilayers were deposited by radio frequency, r.f., reactive magnetron sputtering by using titanium and aluminum targets with 10 cm diameter and 99.99% purity in an argon/nitrogen atmosphere, applying a substrate temperature of 300 ºC. WC inserts were used as substrates to improve the mechanical and tribological properties of TiN/TiAlN multilayer
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-06
-
12. Uma contribuição para o estudo das deformações residuais proporcionadas pelo processo de usinagem por fresamento. / A contribution for residual deformation study originated by the face milling machining process.
The face milling operation purpose is providing flat machined surfaces free from residual strains at the cross section of the workpiece. On the other hand, the evidences presented in this thesis are enough to demonstrate that the strain exists and its behavior can be related to technical measurements such as the cutting tool helical profile, the feed rate, t
Publicado em: 2009