Low Power Circuits
Mostrando 1-12 de 37 artigos, teses e dissertações.
-
1. Developing a stepwise approach to simulate a hammer mill through the Whiten model - the adherence for a gold ore
Abstract Comminution represents a large portion of the capital and operating cost of a mineral processing plant. In 1983, Cohen estimated that comminution processes could account for 30% to 50% of the power consumption of the mill, and typically represents 50% of the operating costs of a mine. Therefore, its optimization is directly related to reduction of t
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
2. Low cost system to measure active power in electrosurgical units
Abstract Introduction: The real-time measurement of active power delivered to patients during the electrosurgical act is still an engineering challenge. Besides, there is no electrosurgical unit on the market capable of doing it according to the normative requirement. Methods This work presents the design of an electronic structure capable to probe the ele
Res. Biomed. Eng.. Publicado em: 09/11/2017
-
3. A passive-matched 22 GHz 2.6-dB-NF CMOS front-end with a 70-800 ps delay block
This paper presents a power-efficient RF differential receiver front-end supporting transmitted-reference (TR) communication in a 90 nm CMOS technology. Particularly, it addresses the issues of designing the frontend amplifier with low-noise and passive matching circuits on a silicon process and integrating a low-power delay unit in the front-end with wideba
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2013-06
-
4. Distributed generators performance during short-circuits considering fault ride-through requirements / Desempenho de geradores distribuídos durante curtos-circuitos considerando requisitos de suportabilidade a afundamentos de tensão = : Distributed generators performance during short-circuits considering fault ride-through requirements
The increase of distributed generation penetration in distribution systems not only helps to diversify the electrical matrix but also brings both technical and economic benefits. Yet, it also raises worries related to energy supply reliability. For wind power plants into the medium and high voltage networks there are the grid codes for "Fault Ride-Through" w
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 03/08/2012
-
5. Vibration energy harvesting using piezoelectric transducer and non-controlled rectifiers circuits
Vibration energy harvesting with piezoelectric materials is of practical interest because of the demand for wireless sensing devices and low-power portable electronics without external power supply. For practical use of vibration energy harvester with piezoelectric materials, it is necessary to process the alternating current (AC) by using different rectifie
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012
-
6. Impacto de técnicas de redução do consumo de energia no projeto de SoCs Multimedia / The impact of design techniques in the reduction of power consumption of SoCs Multimedia
A indústria de semicondutores sempre enfrentou fortes demandas em resolver problema de dissipação de calor e reduzir o consumo de energia em dispositivos. Esta tendência tem sido intensificada nos últimos anos com o movimento de sustentabilidade ambiental. A concepção correta de um sistema eletrônico de baixo consumo de energia é um problema de vár
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 16/06/2011
-
7. Modeling of statistical low-frequency noise of deep-submicrometer MOSFETs
The low—frequency noise (LF-noise) of deep-submicrometer MOSFETs is experimentally studied with special emphasis on yield relevant parameter scattering. A novel modeling approach is developed which includes detailed consideration of statistical effects. The model is based on device physics parameters which cause statistical variations in LF-noise behavior
Publicado em: 2011
-
8. Estudo e implementação de lógica adiabática para circuitos integrados com baixo consumo / Study and implementation of adiabatic logic for low-power integrated circuits
Este trabalho está inserido no ramo de microeletrônica, mais especificamente em circuitos integrados de baixo consumo. Trata-se de um campo importante visando diminuir o consumo de energia mundial, possibilitar a utilização de equipamentos com fonte de baterias por mais tempo e diminuir o custo de resfriamento de circuitos, além do consumo de energia do
Publicado em: 2010
-
9. An estimation method for gate delay variability in nanometer CMOS technology
In the nanoscale regime of VLSI technology, circuit performance is increasingly affected by variational effects such as process variations, power supply noise, coupling noise and temperature changes. Manufacturing variations may lead to significant discrepancies between designed and fabricated integrated circuits. Due to the shrinking of design dimensions, t
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2010
-
10. EXPLORAÇÃO DE OPERADORES ARITMÉTICOS NA TRANSFORMADA RÁPIDA DE FOURIER / ARITHMETICS OPERATORS EXPLORATION IN FAST FOURIER TRANSFORM
The power consumption reduction in the fast Fourier transform (FFT) is important because applications in battery-powered embedded systems grows daily. Thus this work focuses on the application of techniques to reduce power in specific projects of FFT algorithms. The goal is to achieve an architectural exploration in the FFT core, the decimation in time butte
Publicado em: 2010
-
11. Projeto de uma rede de alimentação de baixas perdas para um arranjo de antenas utilizando linhas de fita / Design of a power system for a low-loss antena array using striplines
Este trabalho trata do desenvolvimento teórico e computacional de um arranjo de antenas de grande comprimento elétrico com grande aplicabilidade em radares e sistemas de sensoriamento que utilizam distribuições de potência específicas. São abordados a síntese do padrão de radiação do arranjo, a escolha do número de antenas e o desenvolvimento da
Publicado em: 2010
-
12. SYNTHESIS METHODOLOGY FOR SIMPLIFIED ZVT TOPOLOGIES APPLIED TO BIDIRECTIONAL PWM POLES / METODOLOGIA DE SÍNTESE DE TOPOLOGIAS ZVT SIMPLIFICADAS APLICADAS A PÓLOS PWM BIDIRECIONAIS
Among the soft-switching techniques, the zero-voltage-transition (ZVT) technique has been accepted well by the industry due its attractive characteristics, such as simplicity, low losses in the auxiliary commutation circuit (ACC), operation with soft-switching for a wide load range, and closest operation to the PWM converter counterpart. In three-phase volta
Publicado em: 2009