Inlet
Mostrando 1-12 de 308 artigos, teses e dissertações.
-
1. SEWAGE PERFORMANCE OF A NEW TYPE OF FLAP FILTER
ABSTRACT The drainage performance of a mesh filter determines the water consumption degree of the filter and the efficiency of the next work cycle. Through analysis, we found that the influent flow rate and the sediment content of the influent were important influencing factors. This experiment focused on the drainage time, pressure difference, and cleanline
Eng. Agríc.. Publicado em: 2021-04
-
2. Numerical and experimental evaluation of the thermally stratified atmospheric boundary layer in wind tunnels
Abstract The atmospheric boundary layer (ABL) flow occurs due to the interaction between the Earth’s surface and atmosphere, and it usually happens under thermal stratification. Therefore, in order to emulate this phenomenon, atmospheric wind tunnels need appropriate devices, such as spires and cubical roughness elements, at the entrance of the wind tunnel
REM, Int. Eng. J.. Publicado em: 2021-01
-
3. Physical and mathematical modeling of inclusion behavior in a tundish with gas curtain
Abstract Gas injection in the tundish has been considered as an alternative to optimizing inclusion removal from steels. In the present study, physical and mathematical modeling were used to investigate the effect of gas injection in the tundish on the inclusion removal efficiency. The physical model is a 1/3 reduced scale of an industrial two-strand tundish
REM, Int. Eng. J.. Publicado em: 2020-12
-
4. Investigation of the Relationship between Cerebral Near-Infrared Spectroscopy Measurements and Cerebrovascular Event in Coronary Artery Bypass Grafting Operation in Patients without Carotid Stenosis and Patients with Carotid Stenosis below Surgical Margins
Abstract Objectives: Stroke is an important cause of mortality and morbidity in surgery. In the present study, we examined the cerebral oximetry values of patients with carotid artery stenosis who did not present surgical indications and those who did not present carotid artery stenosis in coronary artery bypass grafting (CABG) surgery by comparing their ce
Braz. J. Cardiovasc. Surg.. Publicado em: 2020-08
-
5. Coinfection of SARS-CoV-2 and Measles morbillivirus in a front-line health worker in Rio de Janeiro, Brasil
Abstract Objectives: Stroke is an important cause of mortality and morbidity in surgery. In the present study, we examined the cerebral oximetry values of patients with carotid artery stenosis who did not present surgical indications and those who did not present carotid artery stenosis in coronary artery bypass grafting (CABG) surgery by comparing their ce
Rev. Assoc. Med. Bras.. Publicado em: 2020-08
-
6. PREPARATION AND SIMULATION OF THE ON-LINE SiO2/S COATING FOR COKING INHIBITION IN THE INDUSTRIAL CRACKING FURNACE
Abstract Coke formation inside radiant coils is one of the main problems during thermal cracking of hydrocarbons. The on-line preparation of the coating for coking inhibition is a promising technology because it provides more flexibility to the operators on site. The SiO2/S coating was prepared on the inner surface of coils in an 8-year-served GK-VI industri
Braz. J. Chem. Eng.. Publicado em: 13/01/2020
-
7. Double-Inlet Single Ventricle with Malposed Great Arteries
Arq. Bras. Cardiol.. Publicado em: 10/10/2019
-
8. SIMULATION OF THERMAL DECOMPOSITION IN AN OPEN CAVITY: ENTROPY ANALYSIS
ABSTRACT This paper presents a numerical analysis of entropy generation in a two-dimensional rectangular channel where the inlet flow undergoes thermal decomposition resulting from a chemical reaction. The model considered viscosity and thermal conductivity to be dependent of temperature. Irreversibility due to mass transport was included in the entropy gene
Braz. J. Chem. Eng.. Publicado em: 15/07/2019
-
9. Characterization of venturi injector using dimensional analysis
RESUMO Injetores Venturi são comumente empregados para fins de fertirrigação na agricultura, extraindo fertilizante de um tanque para a linha de irrigação. O conhecimento da quantidade de líquido a ser injetado por este dispositivo é útil para assegurar operação e manejo adequados da fertirrigação. Os objetivos desta pesquisa foram: (1) conduzir
Rev. bras. eng. agríc. ambient.. Publicado em: 10/07/2019
-
10. Local head loss caused in connections used in micro-irrigation systems
RESUMO Informações sobre perda de carga localizada em conexões utilizadas em sistemas de microirrigação são difíceis de serem encontradas na literatura. O objetivo desta pesquisa foi determinar experimentalmente as perdas de carga localizada em conexões comumente empregadas nesses sistemas e propor modelos matemáticos utilizando o teorema de Bucking
Rev. bras. eng. agríc. ambient.. Publicado em: 10/07/2019
-
11. Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires
Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and aerospace industry as well as in medical engineering field. Small components and tools with complex geome
Mat. Res.. Publicado em: 03/06/2019
-
12. Head loss in laser-perforated thin-walled polyethylene pipes for irrigation
RESUMO Para reduzir custos fixos e operacionais em sistemas de irrigação pressurizados são produzidos tubos de polietileno com pequena espessura de parede, com orifícios de descarga perfurados a laser, que operam a baixas pressões (até 100 kPa). A caracterização hidráulica desses materiais é essencial para o dimensionamento dos sistemas de irrigaç
Rev. bras. eng. agríc. ambient.. Publicado em: 06/05/2019