Hydrodynamic Parameters
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Bioconjugation Between CdTe Quantum Dots and a Cationic Protein: An Analytical Method to Determine Protamine in Drug and Urine Samples
CdTe quantum dots (QD-CdTe) functionalized with mercaptosuccinic acid (MSA) were synthesized in an aqueous medium, varying synthesis time from 0.5 to 4 h. The nanoprobe were characterized by a direct relationship between synthesis time and QD size (2.61-3.04 nm). The QD-CdTe-MSA interacted with protamine (PT), a cationic protein, forming a bioconjugate, thus
J. Braz. Chem. Soc.. Publicado em: 2021-06
-
2. Liquid-phase RTD studies in a flotation column: an analysis between tanks-in-series and axial dispersion models
Abstract The objective of the present study is to evaluate the fluid dynamics of a flotation column (2" in diameter and 6 m in height) based on gas hold-up measurements and, in particular, by applying the liquid-phase RTD (residence time distribution) technique. Additionally, a comparative study is performed between different methodologies used to determine
REM, Int. Eng. J.. Publicado em: 2021-01
-
3. Analysis of physical mechanisms of human body instability for the definition of hazard zones present in emergency action plans of dams. Case study: Santa Helena Dam, Bahia
RESUMO Os impactos produzidos pelas ondas de cheias decorrentes de ruptura de barragens geralmente causam danos irreversíveis à população residente e a perda do equilíbrio do corpo nas inundações contribui para o agravamento desse cenário. Nesse contexto, esse trabalho teve como objetivo analisar a influência da consideração dos mecanismos físico
RBRH. Publicado em: 07/10/2019
-
4. EFFECT OF DISC-BLADE INTERCEPTING ANGLE ON MIXING PERFORMANCE IN A MULTIPHASE STIRRED VESSEL
Abstract The impeller geometry is a determining factor for mixing efficiency in a stirred vessel. In this study, the effect of disc-blade intercepting angle on power number, just suspended speed and mass transfer coefficient was investigated in a multiphase system under turbulent conditions. The impellers used in this study were fabricated with 3D printing.
Braz. J. Chem. Eng.. Publicado em: 30/09/2019
-
5. Aperfeiçoamento de modelo de estimativa da eficiência de remoção de turbidez da água em floculadores tubulares helicoidais
RESUMO Estudos científicos têm demonstrado que os floculadores tubulares helicoidais (FTHs) têm alta eficiência na formação de flocos e baixo tempo de retenção hidráulica, quando comparados aos floculadores comumente usados em tratamento de água e esgoto. No entanto, sua aplicação prática é limitada, pois ainda existe demanda significativa por
Eng. Sanit. Ambient.. Publicado em: 12/08/2019
-
6. Comportamento hidrodinâmico de sistemas alagados construídos de escoamento horizontal subsuperficial de diferentes proporções geométricas e tempos de operação
RESUMO No presente trabalho, teve-se por objetivo avaliar a influência da proporção geométrica e o tempo de operação na hidrodinâmica do sistema. Para isso, três sistemas alagados construídos de escoamento horizontal subsuperficial (SACs-EHSS) de diferentes razões comprimento:largura (L/B) foram caracterizados no que se refere ao comportamento hidr
Eng. Sanit. Ambient.. Publicado em: 25/04/2019
-
7. Three-dimensional numerical simulation of flow in vertical slot fishways: validation of the model and characterization of the flow
RESUMO As escadas para peixes com ranhuras verticais permitem que ocorra a dissipação da energia do escoamento em função da forma da bacia, dos defletores, da declividade longitudinal e da largura da ranhura vertical. Estas estruturas devem apresentar padrões médios e turbulentos do escoamento compatíveis com os peixes que irão transpô-la. Tipicame
RBRH. Publicado em: 11/04/2019
-
8. Mathematical modeling of manganese adsorption onto bone char in a continuous fixed bed column incorporating backmixing and shriking core approaches
Abstract The present study investigated the dynamics of manganese adsorption onto bone char in a continuous fixed bed column using a mathematical model that incorporates: (i) the backmixing model to describe the fluid flow through the bed and (ii) the shrinking core model to describe the kinetic and mass transfer phenomena within spherical adsorbent particle
Braz. J. Chem. Eng.. Publicado em: 2017-07
-
9. Investigation of Wedge Water-Entry Under Symmetric Impact Loads by Experimental Tests
Abstract One of the main challenges for engineers in designing high-speed crafts is the evaluation of hydrodynamic loads during the impact of hull to wave’s surface. This paper presents an experimental investigation on the pressure distribution on three wedge-sections with 15°, 20° and 30° deadrise during water-entry. Assessment of pressure distribution
Lat. Am. j. solids struct.. Publicado em: 2017-06
-
10. Effect of surface finishing on friction and wear of Poly-Ether-Ether-Ketone (PEEK) under oil lubrication
Abstract The tribological properties of poly-ether-ether-ketone (PEEK) containing 30% of carbon fiber were studied in an oil-lubricated environment and different surface finishing of the metallic counterbody. Four different finishing processes, commonly used in the automotive industry, were chosen for this study: turning, grinding, honing and polishing. The
Polímeros. Publicado em: 08/12/2016
-
11. INFLUENCE OF THE MODEL SCALE ON HYDRODYNAMIC SCALING IN CFB BOILERS
Abstract The paper presents the results of experimental verification of the simplified set of scaling parameters for which the particle density as well as the cold model length scale may be chosen independently. The tests were carried out on two large scale 1/10 and 1/20 geometrically similar cold models of the Lagisza 966 MWth supercritical CFB boiler. The
Braz. J. Chem. Eng.. Publicado em: 2016-12
-
12. Geometry and head loss in Venturi injectors through computational fluid dynamics
ABSTRACT To determine the influence of geometry on the hydrodynamic behavior of Venturi injectors, using computational fluid dynamics techniques, we studied, at the Universitat Politècnica de València, Valencia, Spain, the geometric parameters that exert the most influence on head losses: the relationship between throat diameter and nozzle (β), nozzle ang
Eng. Agríc.. Publicado em: 2016-06